HP AlphaServer GS1280 Model 16 Specification page 15

QuickSpecs
GS Options
NOTES:
1. One High Performance I/O Drawer can be used by up to four separate hard partitions. Each of the four I/O
connections (and two associated PCI-X slots) in the High Performance I/O Drawer can be independently controlled
(e.g. power on/off) in conjunction with a separate partition.
2.
A Master I/O Drawer consists of a Standard or High Performance I/O Drawer plus a Combination Adapter in one slot.
The Combination Adapter provides an Ultra3 SCSI connection for two disks and a DVD/CD-RW drive in the drawer,
plus a USB connection for keyboard, mouse, and monitor. The Master I/O Drawer is required for all GS1280 systems
integrated at the manufacturing plant by HP. If the final system configuration does not require these I/O devices, the
Combination Adapter may be removed and replaced with the following alternatives:
System Boot - External storage or network boot can be used in place of the disk storage internal to the I/O
Drawer.
Software Load - Software can be loaded over the network from a disk on another system or directly from a CD
reader attached to another system by using remote mount.
User I/O - User access via a network connection can be used in place of the direct connection via the USB port.
3. The two disks in the Master I/O Drawer can only be connected to the system via the Combination Adapter's Ultra3
SCSI connection. The I/O Drawer design does not permit connection from other storage adapters, such as a RAID
adapter, that might be installed in the I/O Drawer.
4. Each Master I/O Drawer supports up to two, optional, hard disk drives. See the Disks step of the ES/GS Common
Options section of this QuickSpec for the selection of supported disk drives.
Step 6 - Power Distribution Units - Mandatory
Type A North America/Japan 200
Power Distribution -208V, NEMA L21-30P
Units 30A; 3 x C19 outlets plus
Select one variant. 24 x C13 outlets
International 380/415V Y,
IEC 309 32A; 3 x C19
outlets plus 24 x C13
outlets
Type B North America/Japan
Power Distribution 200 - 208V, IEC 309 60A
Units
Select one variant.
International
380/415V Y, IEC 309
32A
NOTES:
1. Select the same power supply voltage variant for both Type A and Type B Power Distribution Units, e.g. both 200-
208V or both 380/415V.
2.
IEC 309 is a general spec that can encompass 3 different pin types. The 3X-H7606-BA PDU uses the Hubbell
460P9W, a 4 pin connector.
3. The 3X-H7606-AA PDU uses an L21-30P 30 amp plug, Hubbell 2811, a 4 pin connector.
3X-H7606-
AA
3X-H7606-
AB
3X-H7606-
BA
3X-H7606-
BB
DA - 11921 Worldwide — Version 24 — July 23, 2007
HP AlphaServer GS1280 Systems
GS1280 Model GS1280 Model
8 16
DA/DY-1280A- DA/DY-1280A-
AA BA
1 required 2 required
(provides (provides
receptacles for receptacles for
power cords power cords
from all system from all system
components) components)
Not applicable Not applicable
GS1280 Model GS1280 Model
32 64
DA/DY-1280A- DA/DY-1280A-
CC BD
2 required 2 required
(provides (provides
receptacles for receptacles for
power cords power cords
from I/O from I/O
Drawers, LAN Drawers, LAN
Hub, and Hub, and
storage storage
shelves) shelves)
2 required 4 required
(for M32/M64 (for M32/M64
Dual AC power Dual AC power
supply supply
exclusively for exclusively for
8P system 8P system
drawers) drawers)
Page 15