Advertisement
Quick Links
PRIMERGY TX150 S4
System configurator and order-information guide
December 2005
Contents
Instructions
Configuration diagram
Configurator
0
System software
II
V
IX Communication/Network
X
System management options
XI Miscellaneous
XII Country specific options
Change report
PRIMERGY Server
Advertisement
Related Manuals for Fujitsu PRIMERGY TX150 S4
Summary of Contents for Fujitsu PRIMERGY TX150 S4
-
Page 1: Table Of Contents
PRIMERGY TX150 S4 System configurator and order-information guide December 2005 Contents Instructions Configuration diagram Configurator System software Basic unit Processor III Memory IV Graphics Accessible drives VI Hard disk drives VII SCSI Controller VIII Disk array IX Communication/Network System management options... - Page 2 This document contains basic product and configuration information that will enable you to configure your system via PC-/ System-Architect. Only these tools will ensure a fast and proper configuration of your PRIMERGY server or your complete PRIMERGY Rack system. You can configure your individual PRIMERGY server in order to adjust your specific requirements.
- Page 3 Configuration diagram PRIMERGY TX150 S4 System unit ( I ) SIDE VIEW Standard Power Supply 1. PSU 2. PSU Redundant power supply option Pentium 4 Processor ( II ) Extension slots SCSI Controller ( VII ) Disk array ( VIII )
- Page 4 Start PRIMERGY TX150 S4 SW Configurator IA32 with OEM-Software for PRIMERGY Server VMware-Software - VCMS VirtualCenter Management Server - GSX Server and GSX Virtual Infrastructure Node - P2V Assistant Enterprise Edition For all SW products please refer to the corresponding software configurator accessible via the Extranet under Configuration &...
- Page 5 Start PRIMERGY TX150 S4 SW Configurator EM64T with OEM-Software for PRIMERGY Server For all SW products please refer to the corresponding software configurator accessible via the Extranet under Configuration & Tools, -All configurations, -Software, URL see below. Microsoft - Software: W...
-
Page 6: I Basic Unit
Start PRIMERGY TX150 S4 Section Basic unit System unit consisting of: * Housing including standard power supply (no redundancy) * Sliding screen with lock (only for floorstand version) Systemboard with: * 7 PCI slots: 1x PCIe x 1 1x PCIe x 4 (x8 Slot) - Page 7 1x per system Enterprise Products - PRIMERGY Server System configurator and order-information guide PRIMERGY TX150 S4 19" Rack version SCSI basic unit (5 U) Pentium 4 processor, memory S26361-K999-V136 PD 820 2.8GHz/800MHz/2x1MB 512MB S26361-K999-V146 PD 820 2.8GHz/800MHz/2x1MB 1GB...
- Page 8 3.) PRIMERGY mounting kit for server racks conforming to EIA standards EIA-310-D for 19" racks. Enterprise Products - PRIMERGY Server System configurator and order-information guide PRIMERGY TX150 S4 "rack-mounting ex factory" This service is to be ordered once per installable server/storage...
-
Page 9: Processor
3x per system max. 3x per system Fujitsu Siemens Computers Enterprise Products - PRIMERGY Server System configurator and order-information guide PRIMERGY TX150 S4 Status 25.11.2005 9 of 18... -
Page 10: Accessible Drives
- 2 x 5.25" bays remaining, can be occupied by 2x accessible drives Setup TX150 S4 by ServerStart is supported with following configurations: no DVD, no CD: remote installation only ( PXE service & DHCP server required) built in CD/DVD: UNC Network share reachable or USB Floppy or MemoryBird connected One of the following USB devices must be used for integrating the drivers during installation process if no automized (e.g. -
Page 11: Hard Disk Drives
SCSI/ RAID controller necessary max. 4x per system Fujitsu Siemens Computers Enterprise Products - PRIMERGY Server System configurator and order-information guide PRIMERGY TX150 S4 Status 25.11.2005 S26361-F3121-E130 Hard disk 300GB in 1" carrier 10000rpm,<5,5ms, 8MB Cache Ultra 320 SCSI (320MB/s) -
Page 12: Scsi Controller
Cable sold separately not mounted in factory. Use this cable only if on-board controller is not used otherwise (eg. S26361-F2814-E6) Fujitsu Siemens Computers Enterprise Products - PRIMERGY Server System configurator and order-information guide PRIMERGY TX150 S4 Status 25.11.2005 12 of 18... -
Page 13: Disk Array
D. LSI - Controller 1-channel Ultra 320 SCSI on-board controller with LSI Integrated Mirroring (IME) Standard SCSI-cabling of a PRIMERGY TX150 S4 basic unit with on-board controller Ultra 320 SCSI controller is connected to the internal hard disks and internal backup devices, if no additional HD/backup device controllers are configured. - Page 14 If internal HDD's are connected at the RAID controller (not IME/ZCR), then for internal accessible drives the cable S26361-F2814-E6 must be ordered additionally! Fujitsu Siemens Computers Enterprise Products - PRIMERGY Server System configurator and order-information guide PRIMERGY TX150 S4 Status 25.11.2005 14 of 18...
- Page 15 RJ45-plug, Cat 5 connection with Cat 5 cabling SW: VLAN, Fast & Gbit Etherchannel max. 4x per system Fujitsu Siemens Computers Enterprise Products - PRIMERGY Server System configurator and order-information guide PRIMERGY TX150 S4 Status 25.11.2005 15 of 18...
- Page 16 In connection with rack configurations the install variant of the modem (S26361-F1652-E4) has to be ordered (see rack configurator) Fujitsu Siemens Computers Enterprise Products - PRIMERGY Server System configurator and order-information guide PRIMERGY TX150 S4 Status 25.11.2005 16 of 18...
- Page 17 A country specific power cord has to be ordered for all floorstand versions: - once per basic unit and an additional second cable - if an second hot plug, redundant power supply modul is ordered. PRIMERGY TX150 S4 Floorstand Power cord for following countries: 1,8 m, grey...
- Page 18 Cange Report Date Order number Changes 2005-11-23 S26361-F1809-E2 ISDN SO Controller PCI Eicon Diva Server BRI-2M 2.0 - now available 2005-03-31 First release Fujitsu Siemens Computers Enterprise Products - PRIMERGY Server System configurator and order-information guide PRIMERGY TX150 S4 Status 25.11.2005...