Page 1
HP Mini 110 and Compaq Mini CQ10 User Guide...
Page 2
Bluetooth is a trademark owned by its common to most models. Some features otherwise using any software product proprietor and used by Hewlett-Packard may not be available on your computer. preinstalled on this computer, you agree to Company under license. SD Logo is a...
Page 3
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
Table of contents 1 Welcome ................................1 Finding information ..........................2 2 Getting to know your computer ........................3 Top ............................... 3 TouchPad ..........................3 Lights ........................... 4 Buttons ..........................5 Keys ............................. 6 Front ..............................7 Right side ............................. 8 Left side ..............................
Page 6
4 Keyboard and pointing devices ........................19 Using the keyboard ..........................20 Identifying the hotkey ......................20 Using the action keys ......................20 Using the TouchPad ........................... 22 Setting pointing device preferences ................... 22 Navigating .......................... 22 Selecting ..........................22 Using TouchPad gestures ....................
Page 7
Resolving a low battery level when a charged battery is available ... 34 Resolving a low battery level when no power source is available ..34 Resolving a low battery level when the computer cannot exit Hibernation ..................34 Conserving battery power ....................34 Storing a battery ........................
Page 8
11 Backup and Recovery ..........................54 Performing a system recovery ......................55 Creating the restore DVDs ....................55 Creating a restore image on a USB device ............... 55 Performing recovery using the restore DVD ..............56 Backing up your information ....................... 57 12 Setup Utility (BIOS) and Advanced System Diagnostics ................
Page 9
The process of burning a disc does not begin, or it stops before completion ....70 Contacting customer support ......................70 Labels ..............................71 Appendix B Cleaning your computer ......................72 Cleaning products ..........................72 Cleaning procedures .......................... 73 Cleaning the display ......................73 Cleaning the sides and cover ....................
Welcome The following sections are included in this chapter: ● Finding information After you set up and register the computer, take the following steps: ● Connect to the Internet—Set up your wired or wireless network so that you can connect to the Internet.
North America: Hewlett-Packard, MS POD, 11311 Chinden Blvd, Boise, ID 83714, USA ● Europe, Middle East, Africa: Hewlett-Packard, POD, Via G. Di Vittorio, 9, 20063, Cernusco s/Naviglio (MI), Italy ● Asia Pacific: Hewlett-Packard, POD, P.O. Box 200, Alexandra Post Office, Singapore 911507 Please include your product number, warranty period (found on your serial number label), name, and postal address.
Getting to know your computer ● ● Front ● Right side ● Left side ● Display ● Bottom TouchPad Component Description TouchPad zone Moves the pointer and selects or activates items on the screen. Left TouchPad button Functions like the left button on an external mouse. Right TouchPad button Functions like the right button on an external mouse.
Lights Component Description Caps lock light On: Caps lock is on. ● Power light White: The computer is on. ● Blinking white: The computer is in the Suspend state. ● Off: The computer is off or in Hibernation. ● Mute light Amber: Computer sound is off.
Buttons Component Description ● Power button When the computer is off, press the button to turn on the computer. ● When the computer is on, press the button briefly to initiate Suspend. ● When the computer is in the Suspend state, press the button briefly to exit Suspend.
Keys Component Description Action keys Execute frequently used system functions. Displays system information when pressed in combination with the key. Operating system logo key Displays the operating system menu. Operating system applications key Displays a shortcut menu for items beneath the pointer. Chapter 2 Getting to know your computer...
Right side Component Description Digital Media Slot Supports the following digital card formats: ● MultiMediaCard ● Secure Digital (SD) Card ● Secure Digital High Capacity Card (SDHC) ● Secure Digital Extended Capacity (SDxC) Supports mini versions by use of an adapter (adapter is not included).
Left side Component Description External monitor port Connects an external VGA monitor or projector. Power connector Connects an AC adapter. ● AC/battery light White: The computer is connected to external power and the battery is fully charged. ● Amber: The computer is connected to external power and the battery is charging.
Display Component Description WLAN antennas (2)* Send and receive wireless signals to communicate with wireless local area networks (WLANs). WWAN antennas (2)* Send and receive wireless signals to communicate with wireless wide-area networks (WWANs). Internal microphone Records sound. Webcam Records video and captures still photographs. To use the webcam, select Computer >...
Bottom Component Description Battery bay Holds the battery. Battery/service door latch Releases the battery from the battery bay and the service door from the computer. Service door Provides access to the hard drive bay, a memory module slot, the subscriber identity module (SIM) slot, and the wireless local area network (WLAN) module.
Networking The following sections are included in this chapter: ● Using an Internet service provider (ISP) ● Identifying wireless and network status icons ● Creating a wireless connection ● Using a WLAN ● Using Bluetooth wireless devices ● Connecting to a wired network Your computer may support one or both of the following types of Internet access: ●...
Using an Internet service provider (ISP) Before you can connect to the Internet, you must establish an ISP account. Contact a local ISP to purchase Internet service and a modem. The ISP can help set up the modem, install a network cable to connect your wireless computer to the modem, and test the Internet service.
Using a WLAN A wireless connection connects the computer to Wi-Fi networks, or WLANs. A WLAN is composed of other computers and accessories that are linked by a wireless router or a wireless access point. NOTE: When creating a wireless connection or allowing access to users in a network, you are prompted for the root password.
Setting up a new WLAN Required equipment: ● A broadband modem (either DSL or cable) (1) and high-speed Internet service purchased from an Internet service provider (ISP) ● A wireless router (purchased separately) (2) ● The wireless computer (3) The illustration below shows an example of a wireless network installation that is connected to the Internet.
NOTE: HP recommends that you select WPA2, which is the most advanced of the three encryption protocols. The use of WEP encryption is not recommended, because it can be overcome with little effort. ● Wi-Fi Protected Access (WPA) and Wi-Fi Protected Access II (WPA2) use security standards to encrypt and decrypt data transmitted over the network.
Using Bluetooth wireless devices A Bluetooth device provides short-range wireless communications that replace the physical cable connections that traditionally link electronic devices such as the following: ● Computers ● Phones ● Audio devices The strength of Bluetooth is in synchronizing information transfers between your computer and wireless devices.
Page 28
Plug the other end of the cable into a network wall jack (2) or a router (not illustrated). Chapter 3 Networking...
Using the keyboard Identifying the hotkey A hotkey is a combination of the key (1) and the key (2). To use a hotkey: ▲ Briefly press the key, and then briefly press the second key of the hotkey combination. Description fn+esc Displays system information.
Page 31
Icon Description Opens Help. Help provides tutorials, answers to questions, and product updates. Decreases the screen brightness level incrementally when you hold down this key. Increases the screen brightness level incrementally when you hold down this key. Switches the screen image among display devices connected to the system. For example, if a monitor is connected to the computer, pressing this key alternates the screen image from computer display to monitor display to simultaneous display on both the computer and the monitor.
Using the TouchPad To move the pointer, slide one finger across the TouchPad in the direction you want the pointer to go. Use the left and right TouchPad buttons like the buttons on an external mouse. Setting pointing device preferences To customize settings for pointing devices, such as button configuration, click speed, and pointer options, select Computer >...
Using TouchPad gestures The TouchPad supports a variety of gestures. To use TouchPad gestures, place two fingers on the TouchPad at the same time. NOTE: TouchPad gestures are not supported in all programs. To turn the gestures on and off: Select Computer >...
Pinching/Zooming Pinching allows you to zoom in or out on images or text. ● Zoom in by placing two fingers together on the TouchPad, and then moving them apart. ● Zoom out by placing two fingers apart on the TouchPad, and then moving them together. NOTE: Pinching/zooming is enabled at the factory.
Multimedia The following sections are included in this chapter: ● Using the audio features ● Using the Webcam ● Using video devices Your computer may include the following: ● Integrated speakers ● Integrated microphones ● Integrated webcam ● Preinstalled multimedia software ●...
Adjusting the volume You can adjust the volume using the action keys. WARNING! To reduce the risk of personal injury, adjust the volume before putting on headphones, earbuds, or a headset. For additional safety information, refer to the Regulatory, Safety and Environmental Notices.
Page 37
▲ To connect a VGA display device, connect the device cable to the external monitor port. Press to switch the image between the display devices connected to the computer. If the computer screen image is not switched to your external monitor after you press f4, follow these steps: Click the Gnome Display Applet icon in the notification area at the far right of the taskbar.
Power management The following sections are included in this chapter: ● Shutting down the computer ● Setting power options ● Using battery power ● Using external AC power Shutting down the computer CAUTION: Unsaved information will be lost when the computer is shut down. The shutdown command closes all open programs, including the operating system, and then turns off the display and computer.
Setting power options Using power-saving states The computer has two power-saving states enabled at the factory: Suspend and Hibernation. When Suspend is initiated, the power lights blink and the screen clears. Your work is saved to memory, letting you exit the Suspend state faster than exiting Hibernation. If the computer is in the Suspend state for an extended period or if the battery reaches a critical battery level while in the Suspend state, the computer initiates Hibernation.
With the computer on, you can initiate Hibernation in any of the following ways: ● Briefly press the power button. ● Select Computer > Shutdown > Hibernate. ● Click the Power icon, located on the far right of the taskbar, and then click Hibernate. To exit Hibernation: ▲...
NOTE: When you disconnect AC power, the display brightness is automatically decreased to save battery life. For information on increasing or decreasing display brightness, refer to Keyboard and pointing devices on page You can keep a battery in the computer or in storage, depending on how you work. Keeping the battery in the computer whenever the computer is plugged into AC power charges the battery and also protects your work in case of a power outage.
Removing the battery CAUTION: Removing a battery that is the sole power source for the computer can cause loss of information. To prevent loss of information, save your work and initiate Hibernation or shut down the computer before removing the battery. Slide the battery/service door latch (1) to release the battery.
To prolong battery life and optimize the accuracy of battery charge displays, follow these recommendations: ● If you are charging a new battery, charge it fully before turning on the computer. NOTE: If the computer is on while the battery is charging, the battery meter in the notification area may show 100 percent charge before the battery is fully charged.
Resolving a low battery level Resolving a low battery level when external power is available Connect one of the following devices: ▲ ● AC adapter ● Optional power adapter purchased as an accessory from HP Resolving a low battery level when a charged battery is available Turn off the computer or initiate Hibernation.
Calibrate a battery before using it if it has been stored for one month or more. Disposing of a used battery WARNING! To reduce the risk of fire or burns, do not disassemble, crush, or puncture; do not short external contacts; do not dispose of in fire or water. Refer to the Regulatory, Safety and Environmental Notices for battery disposal information.
Testing an AC adapter Test the AC adapter if the computer exhibits any of the following symptoms when it is connected to AC power: ● The computer does not turn on. ● The display does not turn on. ● The power lights are off. To test the AC adapter: Shut down the computer.
Drives The following sections are included in this chapter: ● Handling drives ● Replacing or upgrading the hard drive Handling drives CAUTION: Drives are fragile computer components that must be handled with care. Refer to the following cautions before handling drives. Additional cautions are included with the procedures to which they apply.
● If a drive must be mailed, place the drive in a bubble-pack mailer or other suitable protective packaging and label the package “FRAGILE.” ● Avoid exposing a drive to magnetic fields. Security devices with magnetic fields include airport walk-through devices and security wands. Airport conveyer belts and similar security devices that check carry-on baggage use X-rays instead of magnetism and do not damage drives.
Page 49
Maintain the angle as you remove the hard drive (4) from the hard drive bay. Replacing or upgrading the hard drive...
Installing the hard drive Insert the rubber spacers on the drive into the openings (1) in the hard drive bay. Lower the hard drive (2) into the hard drive bay. Replace the Phillips screw (3). Connect the hard drive connector cable (4) to the computer. Lower the service door onto the computer (1) and then slide the door (2) toward the battery bay until the battery/service door latch snaps into place.
Page 51
Reconnect external power and external devices. Turn on the computer. Replacing or upgrading the hard drive...
External cards and devices The following sections are included in this chapter: ● Using Media Card Reader cards ● Using a USB device ● Using optional external devices Using Media Card Reader cards Optional digital cards provide secure data storage and convenient data sharing. These cards are often used with digital media-equipped cameras and PDAs as well as with other computers.
Removing a digital card CAUTION: To reduce the risk of loss of data or an unresponsive system, use the following procedure to safely remove the digital card. Save your information and close all programs associated with the digital card. To remove a digital card: Open File Browser by selecting Computer >...
Connecting a USB device CAUTION: To prevent damage to a USB connector, use minimal force to connect a USB device. ▲ To connect a USB device to the computer, connect the USB cable for the device to the USB port. NOTE: When you connect a USB storage device, you may see a message in the notification area to let you know that the device is recognized by the system.
Using optional external devices NOTE: For more information about required software and drivers, or to learn which computer port to use, refer to the manufacturer's instructions. To connect an external device to the computer: CAUTION: To reduce the risk of damage to the equipment when connecting a powered device, be sure that the device is turned off and the AC power cord is unplugged.
Memory modules The computer has one memory module compartment. The capacity of the computer can be upgraded by upgrading the existing memory module in the memory module slot. WARNING! To reduce the risk of electric shock and damage to the equipment, unplug the power cord and remove all batteries before installing a memory module.
Page 57
Grasp the edge of the memory module (2), and then gently pull the memory module out of the memory module slot. CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module. To protect a memory module after removal, place it in an electrostatic-safe container.
Page 58
Gently press the memory module (3) down, applying pressure to both the left and right edges of the memory module, until the retention clips snap into place. CAUTION: To prevent damage to the memory module, be sure that you do not bend the memory module.
10 Security The following sections are included in this chapter: ● Protecting the computer ● Using passwords ● Using firewall software ● Installing an optional security cable Protecting the computer NOTE: Security solutions are designed to act as deterrents, but they may not deter software attacks or prevent the computer from being mishandled or stolen.
Using passwords A password is a group of characters that you choose to secure your computer information. Several types of passwords can be set, depending on how you want to control access to your information. Passwords can be set in the operating system or in Setup Utility, which is preinstalled on the computer.
Managing an administrator password To set, change, or delete this password, follow these steps: Open Setup Utility by turning on or restarting the computer. While the “Press the ESC key for Startup Menu” message is displayed in the lower-left corner of the screen, press esc. When the Startup Menu is displayed, press f10.
Entering a power-on password At the Enter Password prompt, type your password, and then press enter. After 3 unsuccessful attempts to enter the password, you must restart the computer and try again. Using firewall software Firewalls are designed to prevent unauthorized access to a system or network. A firewall can be a software program you install on your computer and/or network, or it can be a solution made up of both hardware and software.
Installing an optional security cable NOTE: A security cable is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen. NOTE: The security cable slot on your computer may look different from the illustration in this section.
11 Backup and Recovery The following sections are included in this chapter: ● Performing a system recovery ● Backing up your information Recovery after a system failure is as good as your most recent backup. As you add new software and data files, you should continue to back up your system on a regular basis to maintain a reasonably current backup.
Performing a system recovery Recovery allows you to repair or restore the computer to its original factory state. You can create an HP factory image restore DVD, using an external DVD±RW optical drive. You can also create an HP factory restore image on a USB storage device. CAUTION: Using Recovery completely erases hard drive contents and reformats the hard drive.
Performing recovery using the restore DVD If possible, back up all personal files. Shut down the computer. Be sure the restore DVD or USB device is connected to the computer. Restart the computer. Using the arrow keys, select Recovery, and then press enter. Follow the on-screen instructions.
Backing up your information You should back up your computer files on a regular schedule to maintain a current backup. You can manually back up your information to an optional external drive, a network drive, or discs. Back up your system at the following times: ●...
12 Setup Utility (BIOS) and Advanced System Diagnostics Setup Utility, or Basic Input/Output System (BIOS), controls communication between all the input and output devices on the system (such as disk drives, display, keyboard, mouse, and printer). Setup Utility includes settings for the types of peripherals installed, the startup sequence of the computer, and the amount of system and extended memory.
● To select an item, press enter. ● To close a text box or return to the menu display, press esc. ● To display additional navigation and selection information while Setup Utility is open, press f1. Displaying system information Start Setup Utility. Select the Main menu.
Determining the BIOS version To determine whether available BIOS updates contain later BIOS versions than those currently installed on the computer, you need to know the version of the system BIOS currently installed. BIOS version information (also known as ROM date and System BIOS) can be displayed by pressing fn+esc or by using Setup Utility.
Using Advanced System Diagnostics Advanced System Diagnostics allows you to run diagnostic tests to determine if the computer hardware is functioning properly. The following diagnostic tests are available in Advanced System Diagnostics: ● Start-up test—This test analyzes the main computer components that are required to start the computer.
13 MultiBoot About the boot device order As the computer starts, the system attempts to boot from enabled boot devices. The MultiBoot utility, which is enabled at the factory, controls the order in which the system selects a boot device. Boot devices can include optical drives, diskette drives, a network interface card (NIC), hard drives, and USB devices.
Enabling boot devices in Setup Utility The computer will boot to a USB device or a NIC device only if the device has first been enabled in Setup Utility. To start Setup Utility and enable a USB device or a NIC device as a boot device, follow these steps: Turn on or restart the computer, and then press while the “Press the ESC key for Startup Menu”...
Considering boot order changes Before changing the boot order, note the following considerations: ● When the computer restarts after the boot order has been changed, the computer attempts to start using the new boot order. ● If there is more than one type of boot device, the computer attempts to boot using the first device of each type of boot device (except for optical devices).
Choosing MultiBoot preferences You can use MultiBoot in the following ways: ● To set a new boot order that the computer uses each time it is turned on, by changing the boot order in Setup Utility. ● To dynamically choose the boot device, by pressing while the “Press the ESC key for Startup Menu”...
Setting a MultiBoot Express prompt To start Setup Utility and set the computer to display the MultiBoot startup location menu each time the computer is started or restarted, follow these steps: Turn on or restart the computer, and then press while the “Press the ESC key for Startup Menu”...
Troubleshooting and support The following sections are included in this appendix: ● Troubleshooting ● Contacting customer support ● Labels Troubleshooting The following sections describe several common issues and solutions. The computer is unable to start up If the computer does not turn on when you press the power button, the following suggestions may help you determine why the computer does not start up: ●...
repeatedly, the image alternates among the computer display, one or more external displays, and simultaneous display on all devices. Software is functioning abnormally If the software is unresponsive or responds abnormally, restart the computer by selecting Computer > Shutdown > Restart. If you cannot restart the computer using this procedure, refer to the next section, The computer is on but not responding on page The computer is on but not responding...
The wireless network connection is not working If a wireless network connection is not working as expected, follow these suggestions: ● To enable or disable a wireless or wired network device, right-click the Network Connection icon in the notification area, at the far right of the taskbar. To enable devices, select the check box from the menu option.
The process of burning a disc does not begin, or it stops before completion ● Be sure that all other programs are closed. ● Turn off Suspend mode and Hibernation. ● Be sure that you are using the right kind of disc for your drive. ●...
Labels The labels affixed to the computer provide information you may need when you troubleshoot system problems or travel internationally with the computer: ● Serial number label—Provides important information, including the following: Component Product name Serial number (s/n) Part number/Product number (p/n) Warranty period Model description Have this information available when you contact technical support.
Cleaning your computer ● Cleaning products ● Cleaning procedures Cleaning products Use the following products to safely clean and disinfect your computer: ● Dimethyl benzyl ammonium chloride 0.3 percent maximum concentration (For example: germicidal disposable wipes. These wipes come in a variety of brand names.) ●...
Cleaning procedures Follow the procedures in this section to safely clean your computer. WARNING! To prevent electric shock or damage to components, do not attempt to clean your computer while it is turned on: Turn off the computer. Disconnect external power. Disconnect all powered external devices.
Specifications The following sections are included in this appendix: ● Input power ● Operating environment Input power The power information in this section may be helpful if you plan to travel internationally with the computer. The computer operates on DC power, which can be supplied by an AC or a DC power source. The AC power source must be rated at 100–240 V, 50–60 Hz.
Operating environment Factor Metric U.S. Temperature Operating 5°C to 35°C 41°F to 95°F Nonoperating -20°C to 60°C -4°F to 140°F Relative humidity (noncondensing) Operating 10% to 90% 10% to 90% Nonoperating 5% to 95% 5% to 95% Maximum altitude (unpressurized) Operating -15 m to 3,048 m -50 ft to 10,000 ft...
Electrostatic discharge Electrostatic discharge is the release of static electricity when two objects come into contact—for example, the shock you receive when you walk across the carpet and touch a metal door knob. A discharge of static electricity from fingers or other electrostatic conductors may damage electronic components.
Index battery bay, identifying 11 AC battery light, identifying 9 battery, inserting 31 DC plug of external HP power action keys battery, removing 32 supply 74 decrease screen brightness battery/service door latch, default settings, restoring 59 identifying 11 Digital Media Slot, identifying 8 Help 21 BIOS drive light, identifying 9...
Page 88
hotkeys mute 4 optional security cable 53 description 20 power 4 using 20 webcam 10 passwords hubs 43 wireless 4 set in operating system 50 local area network (LAN) set in Setup Utility 50 cable required 17 icons pinching TouchPad gesture 24 connecting cable 17 network 13 ports...