Programming Universal Remote Controls; Programming Your Insignia Universal Remote Control - Insignia NS-42E760A12 User Manual

Insignia 42" LED-LCD HDTV, 1080p
Power
Power consumption
Power input
Miscellaneous
OSD languages
INlink
Game Mode
ENERGY STAR qualified
Internet connectable
TV base screws
V-Chip (version 2.0)
Sleep timer
Channel labeling
VESA mount (mm)
(horizontal × vertical)
Note
The length of the wall-mount screws vary depending
on the wall-mount bracket you purchased. See the
instructions that came with the wall-mount bracket
for screw lengths.
Programming universal
remote controls
Programming your Insignia universal remote
control
To program your remote control:
1 Find the codes for the devices you want to
program in "Manufacturers' codes" on page 58
and write them down or highlight them.
2 Turn on the device (for example, a DVD player)
and, if needed, load media such as a DVD.
3 Press the device button on the TV remote for the
device that you want to program (TV, DVD, STB,
or AUX).
4 Press and hold SET until the red LED blinks
twice, then release.
5 Enter the first five-digit code for the device and
brand that you want to program. The LED blinks
once as each digit is entered. If the code is valid,
the LED blinks twice.
Note
If the LED does not blink twice, repeat steps 2 to 4
and try entering the code again.
6 Aim the remote at the device and press
(power). The device should turn off. If it does
not, repeat Steps 3 through 5, trying each code
for your brand until you find one that works. If
you cannot find a code that works, see
"Searching for your code" below.
7 Repeat Steps 1 to 5 for the other devices you
want to control. For future reference, write down
each working device code.
On: 100W
Standby: <1 W
120V/60Hz
English, French, Spanish
Yes
No
Yes
No
M6 type (12 mm length) (4 pcs)
Yes
Yes
Yes
400 × 400
www.insigniaproducts.com
Searching for your code
If your device does not respond to the remote
control after trying all codes listed for your brand, or
if your brand is not listed, try searching for your
code.
To search for your code:
1 Turn on the device you want to control.
2 Press the device button on your TV remote
control (TV, BD/DVD, DVD, STB, or AUX) once.
3 Press and hold SET until the red LED blinks
twice, then release.
4 Enter 9 9 1. The LED blinks twice.
5 Press the number that matches your device
type.
• 0—Cable converters, video accessories,
satellite receivers
• 1—TVs
• 2—VCRs, DVD players, Blu-ray Disc players
• 3—Audio amplifiers, audio amplifiers/tuners,
CD players
6 Aim the remote at the device and press
(power). The remote sends IR codes from its
library to the selected device, starting with the
most popular code first. If the device responds,
go to Step 8.
7 If the device does not respond, press CH and
the remote tests the next code for that device
type. Continue to press CH until the device
turns off.
Note
Press CH to try the previous code.
8 Now that you have found the correct code, press
SET to save the code that worked for your
device. The LED blinks twice to indicate that the
code has been saved.
9 To search for other device codes, repeat Steps 1
to 8.
Checking the codes
If you have set up the remote using the procedure
in "Searching for your code" on page 53, you may
need to find out which five-digit code is operating
your equipment.
To find out which code is assigned to your TV
(for example):
1 Press TV once.
2 Press and hold SET until the red LED blinks
twice, then release.
3 Enter 9 9 0. The LED blinks twice.
4 To view the code for the first digit, press 1.
Count the red LED blinks (for example, three
blinks = 3), then write down the number in the
appropriate code listing at the top of this
column.
Note
If the LED does not blink, the code digit is 0.
53