Specifications - Samsung SAMTRON 76DF User Manual

Troubleshooting
Check List
Symptom Check List
LED is blinking but no images Is the frequency properly Adjust the frequency properly by
adjusted when checking the referring to the video card manual
on the screen.
Display Timing on the menu? and the Preset Timing Modes.
(The maximum frequency per
resolution may differ from product to
product.)
There are only 16 colors Have the Windows colors been For Windows ME/XP/2000:
set properly? Set the colors properly at the
shown on the screen.
The screen colors have Control Panel, Display, Settings.
changed after changing the
video card.
Has the video card been set Set the video card by referring to the
properly? video card manual.
There is a message that reads Have you installed the monitor Install the monitor driver according to
driver? the Driver Installation Instructions.
"Unrecognized monitor, Plug
& Play (VESA DDC) monitor
See the video card manual to Install the monitor driver according to
found".
see if the Plug & Play (VESA the Driver Installation Instructions.
DDC) function can be supported.
Check the following items if there is trouble with the monitor.
1. Check if the power cord and the cable are properly connected to the computer.
2. Check if the computer beeps more than 3 times when booting.
(If it does, request an after-service for the main board of the computer.)
3. If you installed a new video card or if you assembled the PC, check if the installed the adapter
(video) driver and the monitor driver.
4. Check if the scanning ratio of the video screen is set at 75Hz or 85Hz.
(Do not exceed 60Hz when using the maximum resolution.)
5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove
the Display Adapter at the "Control Panel, System, Device Administrator" and then reboot the computer
to reinstall the adapter (video) driver.
Tips for Highlight Zone
1. To protect CDT against the screen brightness, the Highlight Zone function persists for three hours and then
automatically stops. So please reset it to continue.
2. Once the Highlight Zone has been switched off, you can't select any of the other menus within
the Hightlight Zone.
3. When the Highlight Zone function is operated, the surrounding brightness of screen may become dark.
4. Depending on the video card you use, a color saturation phenomenon may occur in the Highlight Zone.
In this case, slightly lower the contrast of the Highlight Zone and the color saturation will be reduced.
Note If problems repeatedly occur, contact an authorized service center.
26
SAMTRON 76DF
General
Solution Model Name
Picture Tube
Type
Deflection angle
Dot Pitch
Screen type
Maximum Flicker-Free Resolution
1280 Dots, 1024 Lines
Active Display
Horizontal
Verti cal
Synchronization
Horizontal
Vertical
Input Signal Definition
Video Signal
Sync Signal
Display Color
Unlimited
Maximum Pixel Clock
110 MHz
Power Supply
90 ~ 264 VAC rms, 60/50 Hz ± 3 Hz
Power Consumption
90W (Maximum), 80W (Nominal)
Dimensions (WxDxH)
398 x 412 x 400mm (with Stand)
Weight
15.7 kg
Environmental considerations
Operating
Storage
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and
computer systems will provide the best operating conditions and monitor settings. In most cases,
monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Note Design and specifications are subject to change without prior notice.

Specifications

SAMTRON 76DF
17"(43cm) DynaFlat X (40.6cm viewable)
90°
0.20mm (Horizontal)
Aluminized tri-color phosphor dot trio with black matrix.
Anti-doming invar shadow mask.
Multi-layer coated with anti-static.
312 ± 4 mm
234 ± 4 mm
30 ~ 70 kHz
50 ~ 160 Hz
RGB, Analog 0.7 Vpp positive at 75 ohms
Separate H/V sync, TTL level, positive or negative
Temperature 32°F ~ 104°F(0°C ~ 40°C)
Humidity 10% ~ 80%, non-condensing
Temperature -4°F ~113°F (-20°C ~ 45°C)
Humidity 5% ~ 95%, non-condensing
27