Advertisement
PROGRAMMING THE SKYLINK MODEL #38, #38C
7. Set the connectors num-
6. To move the connectors, slide an
bered 1 through 9 so that
opened paper clip into the side of
the switches on the trans-
a connector and lift. (see diagram
M) When repositioning connec-
mitter match those on the
receiver. Leave the re-
tors, place a connector on the two
maining posts at " 0 ",or
chosen posts, then push down on
the connector with your finger.
the blank position (remove
the connectors). See the
diagram J for details.
Paper
Clip
8. Test the transmitter with
the Universal receiver.
Diagram M
PROGRAMMING THE SKYLINK MODEL #88, #88C
1. To Program Your Keypad
2. Set brand jumper by moving the red plastic
- Open the cover on the
tab to the number 7 jumper. Slide an opened
back. (See diagram Q)
paper clip into the
top of the red plastic
tab, then lift and re-
CLOSE
position.
3. Set the frequency
switch located above
to " D " position (slide
OPEN
the switch as far
right as possible).
(See diagram R)
Diagram Q
PROGRAMMING THE SKYLINK MODEL #88p
4. The connector (See diagram V) has 12 rows of posts, each row
has 3 posts. Each row contains one connector (See diagram
W). Set the code connectors from number 1 through 9 so that
the switches on the transmitter match those on the receiver.
To operate with #UR100, only set the connectors to " + " or "0"
(blank position). Do not set the connectors to " - " position. Leave
the remaining posts at " 0 ", or the blank position (remove the
connectors). See the diagram L for details.
Diagram V
Diagram W
5. Refer to the keypad manual to test the transmitter with the Universal
receiver.
PROGRAMMING THE SKYLINK MODEL #68, #68C, #68B, #68G, #68R
1. Locate frequency switch
on the top of the trans-
mitter and set to position
A. (See diagram N)
Diagram N
4. Use a pen or paper clip
to set the corresponding
DIP switches numbered
Frequency
1 through 9 so that the
Switch
switches on the trans-
mitter match those on
the receiver. Each switch
of the transmitter has 3
positions (" + ", " 0 ",
" - "). To operate with
DIP Switch Location
Skylink #UR-100, only
set the switches to " + "
or " 0 ". Do not use " - "
1 2
3
4 5
6
7 8
position. Leave the re-
Brand Jumper
maining DIP switches in
Diagram R
WARRANTY
WARNING
DO NOT let children
If, within one year from date
use any garage door
of purchase, this product
transmitter without
should become defective
adult supervision.
(except battery), due to
Children can injure
faulty workmanship or
themselves or others
materials, it will be repaired
by the garage door.
or replaced, without charge.
Proof of purchase is
required.
2. To program the model
3. The transmitter has 12 rows
#68, #68C, #68B, #68G,
of posts, each row has 3
posts. (see diagram P)
#68R, open the case
with a coin. (See dia-
gram O)
Diagram O
Diagram P
the transmitter at "0" or
the center position. (See
diagram S)
DIP Switch
Location
Diagram S
5. Refer to the keypad manual
to test the transmitter with
the Universal receiver.
FCC
The Universal Garage Door
WARNING:
Remote Control is approved
Changes or modifications
by the FCC and it complies
to this unit not expressly
with Part 15 of the FCC
approved by the party res-
Rules. Its operation is
ponsible of compliance
subject to the following two
could void the user's
conditions :
authority to operate the
1. This device may not
equipment.
cause harmful inter-
ference.
2. This device must accept
any interference that
may cause undesired
operation.
4. Use an opened paper clip to set the connectors numbered
1 through 9 so that the switches on the transmitter match
those on the receiver. To operate with Skylink #UR100, only
set to " + " or " 0 " position. Do not place the connector to
the middle & bottom posts " - " position. Leave the remaining
posts at " 0 ", or the blank position (remove the connectors).
See the Diagram J for details.
5. Test the transmitter with the Universal receiver.
PROGRAMMING THE SKYLINK MODEL #88p
1. To Program Your Keypad
2. Set brand jumper by moving the red plastic
- Open the cover on the
tab to the number 7 jumper. Slide an opened
back. (See diagram T)
paper clip into the
top of the red plastic
tab, then lift and re-
CLOSE
position.
3. Set the frequency
switch located above
to " D " position
OPEN
(slide the switch
as far right as
possible). (See
Diagram T
diagram U)
Skylink will not be held liable
or responsible for
any misuse or application
of this product other than
for its intended use.
SKYLINK
TECHNOLOGIES INC.
2213 Dunwin Drive,
Mississauga, Ontario
L5L 1X1, CANADA
(905)608-9223
(905)608-8744 FAX
Email:support@skylinkhome.com
(Reply within 24 hrs)
Customer Service : (800)304-1187
http://www.skylinkhome.com
P/N. 101A111-003 Rev.3
Patent no. 382251
Patents Pending
©1999 SKYLINK TECHNOLOGIES INC.
Frequency
Switch
Code connector Location
1 2
3
4 5
6
7 8
Brand Jumper
Diagram U
®
GARAGE DOOR/
GATE OPENER
UNIVERSAL RECEIVER
USER'S INSTRUCTIONS
(Model UR-100)
Advertisement
