Contents Introduction ........2 In brief ..........6 Keys, doors and windows .... 19 Seats, restraints ......33 Storage ........50 Instruments and controls ..... 66 Lighting ........93 Infotainment system ....101 Climate control ......104 Driving and operating ....111 Vehicle care .......
"Service reasonable prices. Experienced ■ Directional data, e.g. left or right, or and maintenance" and "Technical mechanics trained by Vauxhall work front or back, always relate to the data" as well as on the identification according to specific Vauxhall direction of travel.
Page 5
Disregarding this information may lead to vehicle damage. Symbols Page references are indicated with 3. 3 means "see page". Thank you for choosing a Vauxhall. We wish you many hours of pleasurable driving. Your Vauxhall Team...
In brief In brief Vehicle unlocking Seat adjustment Seat positioning Initial drive information Turn the key in the driver's door lock to the front or press button q to Pull handle, slide seat, release unlock the doors and load handle. compartment.
In brief Seat backrests Seat height Head restraint adjustment Turn handwheel. Do not lean on seat Lever pumping motion Press release button, adjust height, backrest when adjusting. engage. = higher Seat adjustment 3 35, Seat position down = lower Head restraints 3 33. 3 34, Folding front passenger seat Seats 3 35, Seat position 3 34.
In brief Seat belt Mirror adjustment Exterior mirrors Setting with four-way switch in Interior mirror version with manual window operation Pull out the seat belt and engage in belt buckle. The seat belt must not be Swivel the lever on the underside to twisted and must fit close against the reduce dazzle.
Page 10
In brief Setting with four-way switch in Steering wheel adjustment version with electronic window operation Unlock lever, adjust steering wheel, then engage lever and ensure it is First select the relevant exterior mirror fully locked. Do not adjust steering then use the control to adjust. wheel unless vehicle is stationary and steering wheel lock has been Electric adjustment 3 27, Convex...
Page 12
In brief Side air vents ...... 109 10 Left heated seat ....36 Heated steering wheel ..67 Light switch ......93 Tyre deflation detection Instrument illumination ..98 system ......... 161 Rear fog light ......97 Parking assist ...... 126 Front fog lights .....
Page 14
In brief Exterior lighting Headlight flash, high beam and Turn and lane-change signals low beam right = lever up Turn light switch: left = lever down headlight flash = pull lever = Off high beam = push lever 8 = Side lights Turn and lane-change signals low beam = push or pull lever...
Page 15
In brief Hazard warning flashers Horn Washer and wiper systems Windscreen wiper Operated with the ¨ button. Press j. Hazard warning flashers 3 96. & = fast % = slow $ = timed interval wipe or automatic wiping with rain sensor §...
Page 16
In brief Windscreen and headlight Rear window wiper and washer Climate control washer systems system Heated rear window, heated exterior mirrors Pull lever. Wiper on = push lever Wiper off = push lever again Windscreen and headlight washer Heating is operated by pressing the Wash = push lever and hold system 3 68, Washer fluid 3 139.
Page 17
In brief Demisting and defrosting the Transmission Manual transmission automated windows Manual transmission N = neutral o = drive Air distribution to l. Reverse: with the vehicle stationary, + = higher gear Set temperature control to warmest wait 3 seconds after depressing = lower gear level.
In brief Automatic transmission Starting off Starting the engine Check before starting off ■ Tyre pressure and condition 3 160, 3 198. ■ Engine oil level and fluid levels 3 137. ■ All windows, mirrors, exterior lighting and number plates are free from dirt, snow and ice and are operational.
Page 19
In brief Parking If the vehicle is on a downhill slope, engage reverse gear or set the ■ Always apply parking brake. selector lever to P before switching Manual parking brake without off the ignition. Turn the front pressing release button. Apply as wheels towards the kerb.
Keys, doors and windows Keys, doors and Keys, locks Key with foldaway key section windows Keys Replacement keys The key number is specified in the Keys, locks ........19 Car Pass or on a detachable tag. Doors ........... 24 The key number must be quoted when ordering replacement keys as it Vehicle security ......
Keys, doors and windows Radio remote control Fault Key with foldaway key section If the central locking system cannot be operated with the radio remote control, it may be due to the following: ■ Range exceeded, ■ Battery voltage too low, ■...
Keys, doors and windows Radio remote control A pull on an interior door handle Central locking system with radio unlocks the entire vehicle and opens remote control synchronisation the door. After replacing the battery, unlock the door with the key in the driver's door Notice lock.
Page 23
Keys, doors and windows Central locking system with key Central locking system with radio Central locking button activation remote control Press button m: the doors are locked Turn the key in the driver's door lock Press button p. or unlocked. rearwards.
Keys, doors and windows Fault in radio remote control Fault in central locking system door. The procedure must be carried out for each door. The driver's door Unlocking Unlocking can also be locked from the outside Turn key in the driver's door lock to with the key.
Keys, doors and windows Doors Notice 9 Warning The installation of certain heavy accessories onto the tailgate may Load compartment Use the child locks whenever affect its ability to remain open. children are occupying the rear Opening Closing seats. Using a key or suitable screwdriver, turn button on rear door lock to the horizontal position: door cannot be opened from inside.
Keys, doors and windows Vehicle security Activating with the remote control Light-emitting diode (LED) Anti-theft locking system 9 Warning Do not use the system if there are people in the vehicle! The doors cannot be unlocked from the inside. The system deadlocks all the doors. All doors must be closed or the system cannot be activated.
Page 27
Keys, doors and windows Seek the assistance of a workshop in ignition on then off, then disconnect If the control indicator illuminates the event of faults. the vehicle's battery within 15 after the engine has started, there is seconds. a fault in the engine electronics or Alarm transmission electronics 3 77, To switch off alarm siren:...
Keys, doors and windows Exterior mirrors First select the relevant exterior mirror Folding then use the control to adjust. Convex shape Setting with four-way switch in The convex exterior mirror reduces version with electronic window blind spots. The shape of the mirror operation makes objects appear smaller, which will affect the abilty to estimate...
Page 29
Keys, doors and windows Manual Heated Corsa VXR: For pedestrian safety, the exterior mirrors of the Corsa VXR The exterior mirrors can be folded in Operated by pressing the Ü button. are released from the holder if they by pressing gently on the outer edge are bumped.
Keys, doors and windows Interior mirrors Windows Automatic anti-dazzle Manual anti-dazzle Manual windows Dazzle from following vehicles at night is automatically reduced. The door windows can be opened or To reduce dazzle, adjust the lever on closed with the window winders. the underside of the mirror housing.
Keys, doors and windows Power windows Operating windows from outside Depending on the equipment level, 9 Warning the windows can be operated remotely from outside the vehicle. Take care when operating the power windows. Risk of injury, particularly to children. Keep a close watch on the windows when closing them.
Keys, doors and windows Roof Fault Operated by pressing the Ü button. If the windows cannot be opened or Heating functions with the engine Sunroof closed automatically, activate the running and is switched off window electronics as follows: automatically after a short time. 9 Warning 1.
Page 33
Keys, doors and windows Overload Caution If the system is overloaded, the power supply is automatically cut off for When using a roof rack, check the a short time. The system is protected free movement of the sunroof in by fuses in the fuse box 3 154. order to avoid damage.
Seats, restraints Seats, restraints Head restraints Adjustment Head restraints on front seats Position Head restraints ......33 9 Warning Front seats ........34 Seat belts ........37 Only drive with the head restraint set to the proper position. Airbag system ......39 Child restraints ......
Seats, restraints Front seats Head restraints on rear seats ■ Sit with shoulders as far back against the backrest as possible. Set the backrest rake so that it is Seat position possible to reach the steering wheel with arms slightly bent. 9 Warning Maintain contact between shoulders and the backrest when...
Page 36
Seats, restraints Seat adjustment Pull handle, slide seat, release Seat height handle. 9 Danger Seat backrests Do not sit nearer than 25 cm (10 inches) from the steering wheel, to permit safe airbag deployment. 9 Warning Never adjust seats while driving as they could move uncontrollably.
Folding the backrest forwards is backrest with backrest tilted forward. possible only when the backrest is in an upright position. Corsa VXR Do not operate handwheel to adjust backrest with backrest tilted forward. Heating Lift release lever and tilt backrest forwards.
Seats, restraints Seat belts Seat belt reminder X 3 76. Belt tensioners Seat belts are only designed for use by one person at a time. They are not suitable for people younger than 12 years of age or smaller than 150 cm (5 ft).
Notice your clothing. With the Corsa VXR: Feed seat belt Do not affix or install accessories or through belt mount on backrest when other objects that may interfere with Height adjustment fastening seat belt.
Seats, restraints Airbag system Removing Using the seat belt while pregnant 9 Warning The airbag system consists of a number of individual systems. The lap belt must be positioned as When triggered the airbags inflate low as possible across the pelvis within milliseconds.
Seats, restraints Notice Front airbag system The airbag systems and belt tensioner control electronics are located in the centre console area. Do not put any magnetic objects in this area. Do not stick anything on the airbag covers and do not cover them with other materials.
Seats, restraints The front airbag system is triggered in The side airbag system consists of an 9 Warning the event of an accident of a certain airbag in each front seat backrest and severity in the depicted area. The in the rear outboard seat backrests. Optimum protection is only ignition must be on.
Seats, restraints Curtain airbag system The risk of injury to the upper body The curtain airbag system is triggered and pelvis in the event of a side-on in the event of an accident of a certain The curtain airbag system consists of collision is considerably reduced.
Seats, restraints Airbag deactivation Control indicator W and LEDs in button on: Front airbag and side airbag systems Front passenger airbags are for the front passenger seat have to deactivated and will not inflate in the be deactivated if a child restraint event of a collision.
Seats, restraints Child restraints Deactivation: Control indicator for airbag deactivation 3 76. ■ switch on ignition, control indicator Child restraint systems W flashes, Starting the engine terminates changing of the setting. When a child restraint system is being ■ press button W within 15 seconds The setting can then only be changed used, pay attention to the following and hold down,...
Page 46
Seats, restraints Selecting the right system Only allow children to enter and exit the vehicle at the side facing away Children should travel facing from the traffic. backwards in the vehicle, until as old as possible. It is appropriate to When the child restraint system is not change the system when the child's in use, secure the seat with a seat belt...
Page 47
= Seat available with ISOFIX and Top-tether mounting brackets (Not available on the front passenger seat in the Corsa VXR).
Page 48
Seats, restraints Permissible options for fitting an ISOFIX child restraint system Weight class Size class Fixture On front passenger seat On rear outboard seats On rear centre seat Group 0: up to 10 kg ISO/R1 Group 0+: up to 13 kg ISO/R1 ISO/R2 ISO/R3...
Page 49
Seats, restraints ISOFIX size class and seat device A – ISO/F3 = Forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kg. B – ISO/F2 = Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg. B1 –...
Seats, restraints Isofix child restraint systems Top-tether child restraint systems On the pillar trim of the rear roof and on the attachment points are symbols Fasten vehicle-approved ISOFIX indicating the attachment eyes on child restraint systems to the Fasten Top-tether child restraint which to mount the child restraint mounting brackets.
Storage Storage Storage compartments Cupholders Glovebox Storage compartments ....50 Load compartment ....... 59 Roof rack system ......64 Loading information ..... 64 A cupholder is located in the front of the centre console. The glovebox features: In the 3-door Hatchback, a cupholder is also located at the side of the rear ■...
Storage Underseat storage Rear carrier system Extending Open the tailgate. 9 Warning No people may remain in the extension zone of the rear carrier system, risk of injury. Lift at recessed edge and pull out. The rear carrier system (Flex-Fix Maximum load: 1.5 kg.
Page 53
Storage Install the tail lamps Completely pull out the rear carrier Open out the bulb holder on the back system until you hear it engage. of the tail lamp completely. First remove the rear tail lamp (1), Ensure that it is not possible to push then the front tail lamp (2) from their in the rear carrier system without recesses.
Page 54
Storage Push the clamping lever down and Lock the rear carrier system Unfold pedal crank recesses push the bulb holder into the retainer until it hits the stop. Perform this procedure for both tail lamps. Swivel the left clamping lever (1) back Fold one or both pedal crank first, followed by the right clamping recesses upwards until the diagonal...
Page 55
Storage Adapting the rear carrier system to a bicycle Remove the pedal crank mounts from If the bicycle has curved pedal the pedal crank recesses. cranks, screw in the pedal crank unit all the way (position 1). With the rotary lever on the pedal crank recess, roughly adapt the adjustable pedal crank unit to the protrusion of the pedal crank.
Page 56
Storage Press the release lever and withdraw Prepare the bicycle for Attaching a bicycle to the rear the wheel recesses. attachment carrier system Push the release lever on the strap Rotate the left pedal (opposite the Put on the bicycle. The pedal crank retainer and remove the strap chain cog) vertically downwards.
Page 57
Storage Attach the pedal crank by rotating the attachment screw on the pedal crank mount. Insert pedal crank mount into outer Align the bicycle in the longitudinal rail of each pedal crank recess from direction of the vehicle: Slightly above and slide downwards as far as loosen the pedal mount.
Page 58
Storage Removing a bicycle from the rear Retracting the rear carrier system carrier system Tighten the attachment screw for the pedal bearing mount to its maximum Push the pedal crank mounts into the point. pedal crank recess. Undo strap retainers on both bicycle Secure both bicycle wheels to wheel tyres.
Page 59
Storage Insert the strap retainer and pull tightly downwards as far as possible. Disengage the locking lever on the Swivel first the right clamping lever diagonal support and fold both pedal (1) forwards, followed by the left crank recesses down. clamping lever (2), until they can be Press release lever and slide in wheel engaged in their respective recesses.
Storage Load compartment Push the clamping lever down and pull both bulb holders out of their recesses. Load compartment extension The angle of the rear backrest, in a single unit or split, can be locked in a vertical rather than raked position, for transporting bulky items.
Storage If the backrest is split, unlock the relevant side, and unlock at both sides if it is a single unit. Folding down rear backrests Remove load compartment cover as necessary. Push head restraints down by pressing the catch. Disengage the backrest (single or Move rear seat backrests upright and split) using the release lever and fold allow locking mechanisms to engage...
Page 62
Storage 5-door Hatchback 3-door Hatchback Lift the cover rearwards, until it Lift the cover rearwards until it The load compartment cover consists unlatches, then remove. unlatches, set at an angle, then of four segments which can be remove. individually removed and inserted. Fit in reverse order.
Storage Rear floor storage cover To remove the three other segments If mounted in the upper position, the (order 2 to 4) lift at the rear, space between the load-bay floor and The double load-bay floor can be disengage, twist and remove. the spare wheel well cover can be inserted in the load compartment in used as a stowage compartment.
Storage Lashing eyes Warning triangle First aid kit The lashing eyes are designed to Store warning triangle in rear load Stow the first-aid kit (cushion) in the secure items against slippage, e.g. compartment wall: first fit warning compartment in the left wall of the using lashing straps or luggage net.
Storage Roof rack system Loading information Fitting on model with sunroof Disengage covers concealing roof Roof rack rack mounts by pushing sliders in direction of arrow (e.g. with a coin) For safety reasons and to avoid and remove upwards. To close roof damage to the roof, the vehicle rack mounts, first insert covers at approved roof rack system is...
Page 66
Storage ■ When transporting objects in the To calculate the EC kerb weight, load compartment, the backrests of enter the data for your vehicle in the the rear seats must not be folded Weights table 3 3. forward. The EC kerb weight includes ■...
Instruments and controls Instruments and Controls Steering wheel controls controls Steering wheel adjustment Controls ........66 Warning lights, gauges and indicators ........72 Information displays ..... 81 Vehicle messages ......85 Trip computer ....... 87 Vehicle personalisation ....90 The Infotainment system and the Info-Display can be operated via the controls on the steering wheel.
Instruments and controls Heated steering wheel Horn The steering wheel is heated with the engine running in the area shown in Activate steering wheel heating in Press j. the illustration above. combination with the seat heating by pressing the ß *button with the ignition on until the desired setting is reached.
Instruments and controls Windscreen wiper/washer Run through the windscreen wiper Automatic wiping with rain sensor stages by pushing the lever past the Windscreen wiper resistance point and holding. An acoustic signal sounds at §. Do not use if the windscreen is frozen. Switch off in car washes.
Instruments and controls Pull lever. Washer fluid is sprayed is engaged. Activation or deactivation onto the windscreen and the wiper of this function can be changed. swipes for a few strokes. Vehicle personalisation 3 90. Rear window wiper/washer Outside temperature Keep the sensor free from dust, dirt and ice.
Page 71
Instruments and controls Clock Automatic time synchronisation The RDS signal of most VHF Date and time are shown in the transmitters automatically sets the Info-Display. time, identified by } in the display. Graphic-Info-Display, Some transmitters do not send Color-Info-Display 3 81. a correct time signal.
Instruments and controls Power outlets Electrical accessories that are Ashtrays connected must comply with the electromagnetic compatibility Caution requirements laid down in DIN VDE 40 839. To be used only for ash and not for combustible rubbish. If the tyre repair kit is in operation, no consumers may be connected to the auxiliary power outlet.
Instruments and controls Warning lights, gauges Speed warning To reset, hold the reset knob depressed for a few seconds with the and indicators With the "Personalised key" function ignition on. (P6), a particular maximum speed can be assigned to each vehicle key. Instrument cluster Tachometer When this speed is exceeded,...
Instruments and controls Fuel gauge Service display Transmission display The message InSP appears when it The mode or selected gear is shown Displays the fuel level in the tank. is time for servicing. Further in the transmission display. If the fuel level is too low, Y information 3 175.
Instruments and controls Control indicators The control indicators described are not present in all vehicles. The description applies to all instrument versions. When the ignition is switched on, most control indicators will illuminate briefly as a functionality test. The control indicator colours mean: = danger, important reminder yellow = warning, information, fault...
Page 76
Instruments and controls Control indicators in the instrument cluster...
Instruments and controls Turn signal Fastening the seat belt 3 38. Airbag deactivation O illuminates or flashes green. V illuminates together with the LEDs Airbag and belt tensioners in button W: airbag deactivated Illuminates 3 43. v illuminates red. The control indicator illuminates V flashes: the system can be When the ignition is switched on, the briefly when the parking lights are...
Instruments and controls Flashes during or after engine Service vehicle soon Illuminates start Illuminates when the parking brake is A illuminates or flashes yellow. released if the brake and clutch fluid Battery voltage too low. Have Illuminates when the engine is level is too low 3 139.
Instruments and controls Illuminates for a few seconds after the Fault in power steering system. The Flashing during driving ignition is turned on. The system is power steering may have failed. The The system is actively engaged. ready for operation when the control vehicle can be steered but Engine output may be reduced and indicator goes out.
Instruments and controls Check coolant level 3 138. Deflation detection system Illuminates when the engine is running If there is sufficient coolant, consult w illuminates red or yellow. a workshop. Illuminates red Caution Tyre deflation detected. Stop Preheating and diesel particle Engine lubrication may be immediately and check tyre pressure.
Page 81
Instruments and controls Illuminates Illuminated when high beam is on and 9 Warning during headlight flash 3 94. Level in fuel tank too low. When the engine is off, Flashes Adaptive forward lighting considerably more force is needed Fuel used up. Refuel immediately. to brake and steer.
Instruments and controls Information displays Illuminated when the rear fog light is Graphic-Info-Display, Color- on 3 97. Info-Display Triple-Info-Display Cruise control m illuminates or flashes green. Illuminates Illuminates when the system is on 3 125. Flashes Cruise control was enabled without depressing the brake pedal beforehand.
Page 83
Instruments and controls Selecting functions Select menu items via the menus and Press the multifunction control to using the Infotainment system select the highlighted item or confirm Functions and settings of the buttons. The OK button is used to a command. Infotainment system and electronic select the highlighted item or confirm climate control system are accessed...
Page 84
Instruments and controls Function areas System settings Setting date and time Select menu item Time, Date from the For each function area there is a main Press the Main button of the Settings menu. page (Main), which is selected at the Infotainment system.
Page 85
Instruments and controls On Infotainment systems with Setting units of measure navigation, time and date are also harmonised upon receipt of a GPS satellite signal. The function is activated by highlighting the field in front of Synchron. clock automatical. in the Time, Date menu.
Instruments and controls Vehicle messages Adjusting contrast Always day design: black or coloured (Graphic-Info-Display) text on light background. Always night design: white or Messages are given via the coloured text on dark background. instrument panel display or as warning and signal buzzers. Check Selection is indicated by a o in front control messages appear on the of the menu item.
Instruments and controls engine is running, a gear is Brake light switch engaged and the foot brake is not Brake light does not come on during depressed. braking. Have the cause of the fault ■ Warning signal sounds three times remedied immediately by if the rear carrier system is a workshop.
Instruments and controls Trip computer Range Range is calculated from current fuel tank content and instantaneous consumption. The display shows average values. After refuelling, the range is updated automatically after a brief delay. When the fuel level in the tank is low, a message appears on the display.
Page 89
Instruments and controls Average consumption Trip computer in Graphic-Info- Range is calculated from current fuel tank content and instantaneous Display or Color-Info-Display Display of average consumption. consumption. The display shows The main page of the trip computer Stop watch average values. provides information on range, Measurement of the time from After refuelling, the range is updated...
Page 90
Instruments and controls Instantaneous consumption Average consumption The information of the two trip computers can be reset separately, Displays the instantaneous Displays average consumption. making it possible to evaluate data consumption. At low speeds, Restart trip computer from different time periods. consumption per hour is displayed.
Instruments and controls Vehicle personalisation Stop watch Driving Time incl. Stops The time the vehicle is in motion is recorded. The time the vehicle is The vehicle-specific functions P1 to stationary with the ignition switched P7 can be activated and deactivated. on is included.
Page 92
Instruments and controls ■ Push the wiper lever (right) up or down and select status On or OFF, or input a value for speed (P6) or value for volume (P7). ■ Pull turn signal lever (left) and wiper lever (right) simultaneously to the steering wheel until you hear a confirmation signal (approx.
Page 93
Instruments and controls P4: Automatic locking 3 23. P5: Selective unlocking 3 21. P6: Speed warning 3 72. P7: Volume of the acoustic turn signal 3 96.
Lighting Lighting Exterior lighting Automatic light control Light switch Exterior lighting ......93 Interior lighting ......98 Lighting features ......99 Light switch set to A: When the engine is running, headlights are switched on when external light conditions are Turn light switch: poor.
Lighting High beam Headlight range adjustment 2 = All seats occupied and load compartment laden Manual headlight range 3 = Driver's seat occupied and load adjustment compartment laden Headlights when driving abroad The asymmetrical headlight beam extends visibility at the edge of the road at the passenger side.
Lighting Vehicles with adaptive forward The daytime running lights switch off Corner lighting (2) when the ignition is switched off. lighting On tight bends or when turning off, depending on the steering angle or Adapting the aim of the headlight Adaptive forward lighting the turn signal, an additional left or beam:...
Lighting Hazard warning flashers Turn and lane-change signals Move the lever to the resistance point and hold for longer indication. Switch the turn signal off manually by moving the lever slightly. Short turn signal Push lever to resistance point and release.
Lighting Front fog lights Parking lights Reversing lights The reversing lights come on when the ignition is on and reverse gear is selected. Misted light covers The inside of the light covers may mist up briefly in poor, wet and cold weather conditions, in heavy rain or after washing.
Lighting Interior lighting Interior lights Front courtesy light with reading lights During entry and exit of the vehicle, Instrument panel illumination the front and centre courtesy lights control automatically come on and then switch off after a delay. Front courtesy light Operated with the c button when the doors are closed.
Lighting Lighting features Rear courtesy lights Reading lights Centre console lighting Spotlight in interior mirror housing. Daylight-dependent, automatically regulated centre console lighting. Entry lighting After unlocking the vehicle, the instrument panel lighting, the front and rear foot well lighting and the information display come on for a few seconds.
Lighting Activating Activating with the radio remote control To activate, press button q on the radio remote control twice when the vehicle is locked. Country-specific version: To switch on the function, press button q on the radio remote control once the vehicle is locked.
Infotainment system Infotainment system Introduction Radio Operation Radio reception The Infotainment system is operated Radio reception may be disrupted by Introduction ........ 101 as described in the Infotainment static, noise, distortion or loss of Radio ......... 101 system manual. reception due to Audio players ......
Infotainment system Audio players Phone Seek advice on predetermined installation points for the external antenna or equipment holder and Auxiliary devices Mobile phones and CB radio ways of using devices with equipment The AUX input is located in the centre a transmission power exceeding 10 console in front of the gearshift lever.
Page 104
Infotainment system Caution Mobile telephones and radio equipment may lead to malfunctions in the vehicle electronics when operated inside the vehicle with no exterior antenna, unless the above mentioned regulations are observed.
Climate control Climate control Climate control systems Heating will not be fully effective until engine has reached normal operating temperature. Heating and ventilation system Fan speed Climate control systems ..... 104 Adjust the air flow by switching the fan Air vents ........109 to the desired speed.
Climate control ■ Open side air vents as required and Cooling n Air distribution to l: Air recirculation direct them towards door windows. is deactivated. Operated with the n button and is functional only when the engine and ■ For simultaneous warming of the Maximum cooling fan are running.
Climate control Demisting and defrosting the Electronic climate control The preselected temperature is automatically regulated. In the windows system automatic mode the fan speed and air distribution automatically regulate the air flow. The system can be manually adapted via the use of air distribution and air flow controls.
Page 108
Climate control The electronic climate control system Fan speed Individual menu items are marked by is only fully operational when the turning the centre control and The selected fan speed is indicated engine is running. selected by pressing it. with x and the number in the display. For correct operation do not cover the To exit a menu, turn the centre control If the fan is switched off the air...
Climate control Cooling Select menu item Automatic blower Coolant heater from the Climate menu and select the Diesel-engined vehicles have a fuel- desired fan regulation. powered auxiliary heater. Manual air recirculation mode The manual air recirculation mode is operated with the 4 button. 9 Warning The exchange of fresh air is reduced in air recirculation mode.
Climate control Air vents Maintenance Adjustable air vents Air intake At least one air vent must be open while cooling is on in order to prevent the evaporator from icing up due to lack of air movement. To close the vent, turn the adjuster wheel to turn the adjuster wheel left or right to its stop.
Climate control Air conditioning regular operation In order to ensure continuously efficient performance, cooling must be operated for a few minutes once a month, irrespective of the weather and time of year. Operation with cooling is not possible when outside temperature is too low.
Driving and operating Driving and Driving hints Starting and operating operating Control of the vehicle New vehicle running-in Do not brake unnecessarily hard for Never coast with engine not the first few journeys. running Driving hints ....... 111 During the first drive, smoke may Many systems will not function in this occur because of wax and oil Starting and operating ....
Driving and operating Ignition switch positions Starting the engine Overrun cut-off The fuel supply is automatically cut off during overrun, i.e. when the vehicle is driven with a gear engaged but accelerator is released. Overrun cut- off is deactivated if catalytic converter temperature is high.
Driving and operating Engine exhaust switching off the ignition. On an take up to 25 minutes. Fuel uphill slope, turn the front wheels consumption may be higher during away from the kerb. this period. The emission of smells and smoke during this process is 9 Danger If the vehicle is on a downhill slope, normal.
Driving and operating Caution Fuel grades other than those listed on pages 3 127, 3 186 could damage the catalytic converter or electronic components. Unburnt petrol will overheat and damage the catalytic converter. Therefore avoid excessive use of the starter, running the fuel tank dry and starting the engine by pushing or towing.
Driving and operating Automatic transmission Selector lever The engine can only be started with lever in position P or N. When position N is selected, press brake pedal or The automatic transmission permits apply parking brake before starting. automatic gearshifting. Do not accelerate while engaging a gear.
Page 117
Driving and operating Rocking the vehicle Electronic driving programmes Activate the Winter programme to assist starting off on a slippery road Rocking the vehicle is only ■ Following a cold start, the operating surface. permissible if the vehicle is stuck in temperature programme increases sand, mud or snow.
Page 118
Driving and operating Kickdown 2nd gear is not available. Manual shifting: = 1st gear = 3rd gear 3, D = 4th gear Have the cause of the fault remedied by a workshop. Interruption of power supply In the event of an interruption of power supply, the selector lever 2.
Driving and operating Manual transmission Caution It is inadvisable to drive with hand resting on the selector lever. 3. Push the yellow catch forward with a screwdriver and move the selector lever out of P. If P is To engage reverse, with the vehicle engaged again, the selector lever stationary wait 3 seconds after will be locked in position again.
Driving and operating Manual transmission Starting the engine Always move the selector lever in the appropriate direction as far as it will automated Depress the foot brake when starting go. Upon release, it automatically the engine. If the foot brake is not returns to the centre position.
Driving and operating If neither the accelerator nor the Rocking the vehicle If engine speed is too high, the brake pedal are depressed, no gear transmission only switches to a higher Rocking the vehicle is only is engaged and A or R flashes for gear via kickdown.
Page 122
Driving and operating Sport mode Deactivation Deactivation The Sport mode is switched off by: The Winter mode is switched off by: ■ pressing the S button again, ■ pressing the T button again, ■ turning off the ignition, ■ turning off the ignition, ■...
Driving and operating Fault 5. Using a flat-head screwdriver, turn the adjusting screw under the To prevent damage to the manual cap clockwise until clear transmission automated, the clutch is resistance can be felt. The clutch engaged automatically at high clutch has now been disengaged.
Driving and operating Brakes ABS starts to regulate brake pressure Fault as soon as a wheel shows a tendency to lock. The vehicle remains 9 Warning The brake system comprises two steerable, even during hard braking. independent brake circuits. If there is a fault in the ABS, the ABS control is made apparent If a brake circuit fails, the vehicle can wheels may be liable to lock due...
Driving and operating Ride control systems Parking brake Brake assist If the brake pedal is depressed Electronic stability program quickly and forcefully, maximum brake force is automatically applied Electronic stability program (full braking). (ESP® Plus ) improves driving stability when necessary, regardless of the Maintain steady pressure on the type of road surface or tyre grip.
Driving and operating Cruise control When ESP® Plus is deactivated the 9 Warning control indicator v illuminates. ESPoff also appears in the service The cruise control can store and Do not let this special safety display. maintain speeds of approx. 30 (20) to feature tempt you into taking risks 200 km/h (120 mph).
Driving and operating Object detection systems With automatic transmission or When switch m is released the manual transmission automated, only current speed is stored and activate cruise control in automatic maintained. Parking assist mode. Reduce speed Control indicator m 3 81. With cruise control active, turn switch g downwards and hold, or turn briefly Activation...
Driving and operating Fuel Activation 9 Warning Fuel for petrol engines Under certain circumstances, Only use unleaded fuel that complies various reflective surfaces on with DIN EN 228. objects or clothing as well as external noise sources may cause Fuels with ethanol content greater the system to fail to detect than 5 % may only be used if the obstacles.
Page 129
Driving and operating a biodiesel (= FAME according to Refuelling 9 Danger EN14214) content of max. 7 % by volume (like DIN 51628 or equivalent Fuel is flammable and explosive. standards) may be used. No smoking. No naked flames or Do not use marine diesel oils, heating sparks.
Page 130
Driving and operating Fuel consumption - CO equipment may result in slightly higher fuel consumption and CO Emissions emission levels and a lower maximum The determination of fuel speed. consumption is regulated by Fuel consumption, CO emissions European directive 80/1268/EEC 3 190.
Driving and operating Towing If the trailer starts snaking, drive more level. Since engine power decreases slowly, do not attempt to correct the as altitude increases due to the air steering and brake sharply if becoming thinner, therefore reducing General information necessary.
Driving and operating the case of heavy trailers. The vertical national maximum speeds are When inserting, fit protective cap over coupling load should never fall below specified for trailer operation, they rotary knob with key. 25 kg. must be complied with. Fitting the coupling ball bar Rear axle load Towing equipment...
Page 133
Driving and operating Checking the tensioning of the coupling ball bar Disengage and fold down the socket. ■ Place the key in the lock and unlock Remove the sealing plug from the the coupling ball bar. opening for the coupling ball bar and ■...
Page 134
Driving and operating Inserting the coupling ball bar Eye for break-away stopping cable Attach breakaway stopping cable to eye. Check that the coupling ball bar is correctly installed ■ Green marking on rotary knob is visible. ■ There must be no gap between the rotary knob and the coupling ball bar.
Page 135
Driving and operating Dismounting the coupling ball bar Insert the key in the lock and unlock the coupling ball bar. Push the rotary knob onto the coupling ball bar and rotate right while pressed down until it engages. Pull out the ball bar downwards. Insert sealing plug in opening for coupling ball bar.
Vehicle care Vehicle care General Information ■ Drain washer fluid reservoir. ■ Check coolant antifreeze and Accessories and vehicle corrosion protection. modifications ■ Adjust tyre pressure to the value General Information ....135 specified for full load. We recommend using Genuine Parts Vehicle checks ......
Vehicle care Vehicle checks ■ Check the engine oil level. 9 Danger ■ Check the coolant level. Performing work ■ Fit the number plate if necessary. The ignition system and Xenon headlights use extremely high voltage. Do not touch. End-of-life vehicle recovery Information on end-of-life vehicle The caps for topping up the engine oil, recovery centres and the recycling of...
Vehicle care Pull the release lever and return it to Check with the vehicle on a level its original position. surface. The engine must be at operating temperature and switched off for at least 5 minutes. Pull out the dipstick, wipe it clean, insert it to the stop on the handle, pull out and read the engine oil level.
Vehicle care We recommend to use the same engine oil that is filled in. The engine oil level must not exceed the MAX mark on the dipstick. Caution Overfilled engine oil must be drained or suctioned out. Capacities 3 197. Fit the cap on straight and tighten it.
Vehicle care concentration checked and have the Brakes cause of the coolant loss remedied by A squealing noise indicates that the a workshop. brake lining is at its minimum thickness. Continued driving is Washer fluid possible but have the brake lining replaced as soon as possible.
Vehicle care Batteries do not belong in household We recommend that you have the Wiper blade replacement waste. They must be disposed of at battery replaced by a workshop. Service setting for front an appropriate recycling collection windscreen wipers point. Diesel fuel system bleeding Laying up the vehicle for more than If the tank has been run dry, the diesel...
Vehicle care Bulb replacement Wiper blades on the windscreen Wiper blade on the rear window Switch off the ignition and switch off the relevant switch or close the doors. Only hold a new bulb at the base! Do not touch the bulb glass with bare hands.
Vehicle care system reservoir filler neck from Low beam 2. Press base to the side and above. Washer fluid may escape if remove from reflector. the reservoir is full to the top. Halogen headlights 1. Disengage wire clip and remove 3.
Page 144
Vehicle care High beam Side lights 3. Disengage spring clip from retainer by moving and swivelling 1. Rotate protective cover 2 1. Rotate protective cover 2 to the side. anticlockwise and remove. anticlockwise and remove. 4. Remove bulb from reflector 2.
Page 145
Vehicle care 3. Remove bulb from socket and Low beam renew bulb. 4. Insert holder in reflector. Install the protective cover. Adaptive forward lighting 2. Withdraw side light bulb holder from reflector. 1. Disengage wire clip and remove protective cover 1. Headlights have separate systems for low beam 1 (outer bulbs) and high beam 2 (inner bulbs).
Page 146
Vehicle care 4. Insert new bulb in reflector so that the locating tab of the bulb holder aligns with the reflector recess. Attach the bulb holder so that the locating tab is on the side. 5. Engage bulb. 6. Attach connector to bulb. 7.
Page 147
Vehicle care Cornering light 2. Detach wiring connector from bulb. 3. Disengage spring clip from retainer by moving and swivelling 1. Rotate protective cover 2 to the side. 3. Disengage spring clip from anticlockwise and remove. 4. Remove bulb from reflector retainer by moving and swivelling housing.
Vehicle care Side lights 2. Withdraw side light bulb holder Front turn signal lights from reflector. 1. Rotate protective cover 2 1. Rotate bulb holder anti-clockwise 3. Remove bulb from socket and anticlockwise and remove. to disengage. renew bulb. 4. Insert holder in reflector. Install the protective cover.
Page 149
Vehicle care Tail lights 2. Remove plug connector by pressing on bulb holder tab. 5-door Hatchback 3. Hold bulb housing from the outside; unscrew two retaining nuts. 2. Push bulb into socket slightly, rotate anti-clockwise, remove and renew bulb. 3. Insert bulb holder in reflector, 1.
Page 150
Vehicle care 6. Push bulb into socket slightly, rotate anti-clockwise, remove and renew bulb. Tail light (1) Reverse light (2) Turn signal light (3) Tail light/brake light (4) Rear fog light, may be only on one side (5) 7. Engage bulb holder in bulb housing, ensuring that it properly 5.
Page 151
Vehicle care 3-door Hatchback, van 2. Remove plug connector by pressing on bulb holder tab. 3. Hold bulb housing from the outside; unscrew two retaining nuts. 5. Gently press the three locking lugs on the outside of the bulb 1. Open side cover. holder outwards and remove bulb holder.
Vehicle care Number plate light 6. Push bulb into socket slightly, 8. Ensure that the bulb holder seal is rotate anti-clockwise, remove and positioned as illustrated. Fit the 1. Insert screwdriver in bulb renew bulb. round seal on the fastening bolt. housing, press to the side and Reverse light (right side), rear fog 9.
Page 153
Vehicle care Interior lights Front courtesy light 4. Rotate bulb holder anti-clockwise 2. Remove bulb housing to disengage. downwards, taking care not to pull on the cable. 5. Remove bulb from holder and renew bulb. 1. Disengage and remove lens at the 3.
Page 154
Vehicle care Front courtesy light, reading lights Glovebox light, foot well light 2. Press bulb slightly towards spring clip and remove. 3. Insert new bulb. 4. Install lamp. 1. Disengage lens, press it 1. Prise the lamp out with downward slightly and remove at a screwdriver.
Vehicle care Electrical system Engine compartment fuse box Fuses Data on the replacement fuse must match the data on the defective fuse. There are three fuse boxes in the vehicle: ■ in the front left of the engine compartment, ■ in the interior behind the light switch, or, in right-hand drive vehicles, behind the glovebox, ■...
Page 156
Vehicle care No. Circuit No. Circuit Starter 14 Manual transmission automated Air conditioning system 15 High beam (right) Diesel fuel filter heater 16 High beam (left) Horn 17 Main relay Manual transmission automated, automatic 18 Engine control unit transmission 19 Airbags Engine control unit 20 Main relay Fog lights...
Vehicle care The fuse box is behind the the light No. Circuit switch. Pull the top edge of the panel 30 Air conditioning system and fold down. 31 Power window (left) 32 Power window (right) 33 Heated exterior mirrors 34 – 35 –...
Vehicle care Vehicle tools Vehicles with spare wheel Vehicles with tyre repair kit Tools The jack and the vehicle tools are in The vehicle tools are in the right-hand the right-hand compartment in the compartment in the load load compartment. To open the compartment, disengage compartment, together with the tyre the cover and open it.
Vehicle care Wheels and tyres Winter tyres Caution Winter tyres improve driving safety at temperatures below 7 °C and should Tyre condition, wheel condition Check tyre pressures regularly therefore be fitted on all wheels. even if run-flat tyres are fitted. Drive over edges slowly and at right Tyres of size 195/60 R 15, angles if possible.
Vehicle care Driving with a damaged tyre = Load index e.g. 88 is equivalent to 567 kg A loss in tyre pressure is indicated by = Speed code letter the deflation detection system. If a tyre has no pressure, continued Speed code letter: driving is possible Q = up to 160 km/h (100 mph)
Vehicle care System initialisation 9 Warning If the pressure is too low, this can result in considerable tyre warm- up and internal damage, leading to tread separation and even to tyre blow-out at high speeds. Tyre deflation detection system The tyre deflation detection system The legally permissible minimum continually checks the rotation speed tread depth (1.6 mm) has been...
Vehicle care Changing tyre and wheel size Wheel covers must not impair brake Always use fine mesh chains that add cooling. no more than 10 mm to the tyre tread If tyres of a different size than those and the inboard sides (including chain fitted at the factory are used, it may be 9 Warning lock).
Page 164
Vehicle care Tyre damage exceeding 4 mm or that The tyre repair kit is in the stowage is at tyre's sidewall near the rim compartment in the load cannot be repaired with the tyre repair compartment. kit. To open the compartment, disengage the cover and open it.
Page 165
Vehicle care 4. Unscrew valve cap from defective 9. The compressor pressure gauge tyre. briefly indicates up to 6 bar whilst the sealant bottle is emptying 5. Screw tyre inflation hose to valve. (approx. 30 seconds). Then the 6. Screw air hose onto compressor pressure starts to drop.
Page 166
Vehicle care 12. Push catch on bracket to remove If the tyre pressure has fallen Notice sealant bottle from bracket. Screw below 1.3 bar, the vehicle must The driving characteristics of the tyre inflation hose to free not be used. Seek the assistance repaired tyre is severely affected, connection of sealant bottle.
Vehicle care Wheel changing ■ Never crawl under a jacked-up Alloy wheels: Disengage wheel vehicle. bolt caps with a screwdriver and Some vehicles are equipped with remove. To protect the wheel, ■ Do not start the vehicle when it is a tyre repair kit instead of a spare place a soft cloth between the raised on the jack.
Page 168
10. Align the valve hole in the wheel cover with the tyre valve before With versions of the Corsa VXR installing. with sill panelling or retrofitted sill panelling no jack must be used. Install wheel bolt caps.
In the Corsa van the spare wheel is The spare wheel can be classified as screwed down together with the floor Only mount one temporary spare a temporary spare wheel depending cover.
Vehicle care Jump starting ■ Wear eye protection and protective clothing when handling a battery. ■ Use a booster battery with the Do not start with quick charger. same voltage (12 Volts). Its A vehicle with a discharged battery capacity (Ah) must not be much can be started using jump leads and less than that of the discharged the battery of another vehicle.
Vehicle care Towing 4. Connect the other end of the black To start the engine: lead to a vehicle grounding point, 1. Start the engine of the vehicle such as the engine block or an Towing the vehicle providing the jump. engine mounting bolt.
Vehicle care Screw in the towing eye as far as it will Vehicles with automatic transmission go until it stops in a horizontal must be towed facing forwards, not position. faster than 80 km/h (50 mph) nor further than 100 km (60 miles). In all Attach a tow rope –...
Vehicle care Appearance care Disengage cap at bottom and remove Caution downwards. Exterior care The towing eye is stowed with the Drive slowly. Do not drive jerkily. vehicle tools 3 158. Excessive tractive force can Locks damage the vehicle. The locks are lubricated at the factory using a high quality lock cylinder After towing, unscrew the towing eye grease.
Page 174
Vehicle care window wiper must be switched off. Polishing and waxing Clean smearing wiper blades with Remove antenna and external a soft cloth and window cleaner. Wax the vehicle regularly (at the accessories such as roof racks etc. latest when water no longer beads). Sunroof Otherwise, the paintwork will dry out.
Vehicle care Underbody The instrument panel should only be cleaned using a soft damp cloth. Some areas of the vehicle underbody have a PVC undercoating while other Clean fabric upholstery with critical areas have a durable a vacuum cleaner and brush. protective wax coating.
Service and maintenance Service and General information Fixed service interval When service is due, InSP appears in maintenance Service information the odometer display for approximately 10 seconds when the In order to ensure economical and ignition is switched on. Have the next safe vehicle operation and to service performed by a workshop maintain the value of your vehicle, it...
Page 177
Service and maintenance Display of remaining distance: 1. Switch off ignition. 2. Briefly press the trip odometer reset button. The odometer reading is shown. 3. Press and hold the reset button for approx. 2 seconds. InSP and the remaining distance are displayed.
Service and maintenance Scheduled maintenance Service schedules Service schedule by year km (x 1000) Service operations miles (x 1000) Check visually control unit, lighting unit and signalling equipment as well as airbag, check steering wheel lock and ignition switch Replace batteries for radio remote control (Do not forget the second key) Every 2 years Check windscreen wipers, windscreen washer system and headlight washer system...
Service and maintenance by year km (x 1000) Service operations miles (x 1000) Replace air cleaner insert Every 4 years / 60,000 km / 40,000 mls Replace spark plugs Every 4 years / 60,000 km / 40,000 mls Visually inspect ribbed V-belt Replace ribbed V-belt, Every 10 years / 150,000 km / 100,000 mls Z 13 DTJ, Z 13 DTH, Z 13 DTR, Z 13 DTI, Z 17 DTR...
Page 180
Service and maintenance by year km (x 1000) Service operations miles (x 1000) Check exterior of body/underbody corrosion protection and note any damage in the Service and Warranty Booklet Visually inspect front and rear wheel brakes Annual service if annual mileage exceeds 20,000 km / 12,000 mls. Engine, transmission (AT, MT), inspect air-conditioning compressor for leaks Remove brake drum, clean, visually check...
Page 181
Service and maintenance by year km (x 1000) Service operations miles (x 1000) Undo wheel fastening (take care if tyre pressure monitoring system is present) and tighten to torque: 110 Nm. The wheel bolt taper should be greased or oiled lightly during assembly. Check tyre condition.
Page 182
Service and maintenance +: Additional operations. o: Under extreme operating conditions and if required by country-specific conditions, the intervals are reduced.
Service and maintenance Recommended fluids, Additional servicing Police vehicles, taxis and driving school vehicles are also classified as lubricants and parts Additional operations + operating under extreme conditions. Additional operations are not required Under extreme operating conditions, Recommended fluids and every service but can be performed in it may be necessary to have certain lubricants...
Page 184
Service and maintenance = General Motors Europe Engine oil additives function problems. Liability for = Longlife consequences resulting from the use The use of engine oil additives could A or B = Engine oil quality of coolant additives will be rejected. cause damage and invalidate the specification warranty.
Technical data Technical data Vehicle identification Identification plate Vehicle Identification Number Vehicle identification ....184 Vehicle data ....... 186 The identification plate is located on the front right door frame. The Vehicle Identification Number is stamped on the identification plate and on the floor pan, under the floor covering, visible under a cover.
Page 186
Technical data Information on identification plate: 1 = Manufacturer 2 = Type approval number 3 = Vehicle Identification Number 4 = Permissible gross vehicle weight rating 5 = Permissible gross train weight 6 = Maximum permissible front axle load 7 = Maximum permissible rear axle load 8 = Vehicle-specific or countryspecific data...
Technical data Vehicle dimensions 5-door Hatchback 3-door Hatchback VXR Van Length [mm] 3999 3999 4040 3999 Width without exterior mirrors [mm] 1737 1713 1713 1713 Width with two exterior mirrors [mm] 1944 1944 1924 1944 Height (without antenna) [mm] 1488 1488 1488 1488 Length of load compartment floor [mm]...
Page 198
Technical data Capacities Engine oil Z12XEP, Z16LEL, Z13DTJ, Z13DTI, Engine Z10XEP Z14XEP Z16LER Z13DTH Z13DTR Z13DTJ ECO Z17DTR including Filter [l] between MIN and MAX [l] Fuel tank Z12XEP, Z16LEL, Z13DTJ, Z13DTI, Engine Z10XEP Z14XEP Z16LER Z13DTH Z13DTR Z13DTJ ECO Z17DTR Petrol/diesel, nominal capacity [l]...
Page 199
Technical data Tyre pressures Comfort with up to With full load 3 people ECO with up to 3 people Engine Tyres front rear front rear front rear [kPa/bar] [kPa/bar] [kPa/bar] [kPa/bar] [kPa/bar] [kPa/bar] (psi) (psi) (psi) (psi) (psi) (psi) Z10XEP 185/70 R14, 200/2.0 180/1.8...
Page 200
Technical data Comfort with up to With full load 3 people ECO with up to 3 people Engine Tyres front rear front rear front rear [kPa/bar] [kPa/bar] [kPa/bar] [kPa/bar] [kPa/bar] [kPa/bar] (psi) (psi) (psi) (psi) (psi) (psi) Z12XEP, 185/70 R14, 200/2.0 180/1.8 270/2.7 (39) 250/2.5 (36) 260/2.6...
Page 201
Technical data Comfort with up to With full load 3 people ECO with up to 3 people Engine Tyres front rear front rear front rear [kPa/bar] [kPa/bar] [kPa/bar] [kPa/bar] [kPa/bar] [kPa/bar] (psi) (psi) (psi) (psi) (psi) (psi) Z16LEL, Z16LER 195/55 R16 240/2.4 220/2.2 270/2.7 (39) 250/2.5 (36) 260/2.6...
Page 202
Technical data Comfort with up to With full load 3 people ECO with up to 3 people Engine Tyres front rear front rear front rear [kPa/bar] [kPa/bar] [kPa/bar] [kPa/bar] [kPa/bar] [kPa/bar] (psi) (psi) (psi) (psi) (psi) (psi) Z13DTJ 185/70 R14 200/2.0 180/1.8 270/2.7 (39) 250/2.5 (36) 260/2.6...
Page 203
Technical data Comfort with up to With full load 3 people ECO with up to 3 people Engine Tyres front rear front rear front rear [kPa/bar] [kPa/bar] [kPa/bar] [kPa/bar] [kPa/bar] [kPa/bar] (psi) (psi) (psi) (psi) (psi) (psi) Z13DTI, 185/65 R 15, 220/2.2 200/2.0 270/2.7 (39) 250/2.5 (36) 260/2.6...
Page 204
Technical data Comfort with up to With full load 3 people ECO with up to 3 people Engine Tyres front rear front rear front rear [kPa/bar] [kPa/bar] [kPa/bar] [kPa/bar] [kPa/bar] [kPa/bar] (psi) (psi) (psi) (psi) (psi) (psi) 185/60 R15 260/2.6 220/2.2 270/2.7 (39) 250/2.5 (36) 270/2.7 320/3.2...
Page 205
Technical data Towing hitch installation dimensions...
Customer information Customer Vehicle data recording manufacturer will not access information about a crash event or and privacy information share it with others except ■ with the consent of the vehicle Event data recorders owner or, if the vehicle is leased, The vehicle has a number of with the consent of the lessee, Vehicle data recording and...