Fostex DE-10 Owner's Manual page 20

DE-10 Owner's Manual
2 MODE SINGLE1/DUAL SINGLE 2
L G DELAY DISTORTION
L H MISC G.MULTI 1
I CHORUS G.MULTI 2
J PITCH B.MULTI
M K FLANGER VO.MULTI
M
<Front panel settings>
1. Set the MODE switch to "SINGLE 1" or "SINGLE 2".
2. Set the TYPE switch to the desired position.
You can select from among the following eleven types for
each single mode. See page 8~15 for details about each
type.
• When selecting "SINGLE 1".
MODE
SINGLE 1/DUAL SINGLE 2
SW
L. HALL L. HALL
A
B S. HALL S. HALL
C ROOM ROOM
D PLATE
PLATE
E VOCAL MIC SIM
F DELAY + REV AMP SIM
• When selecting "SINGLE 2".
MODE
SINGLE 1/DUAL SINGLE 2
SW
L. HALL
A L. HALL
S. HALL
B S. HALL
C ROOM
ROOM
D
PLATE PLATE
E VOCAL MIC SIM
F AMP SIM
DELAY + REV
3. Set the VARIATION switch to the desired position.
4. Using the ADJUST (PARAM 1 through PARAM 3) controls,
adjust the effect parameters.
In the single mode, you can control three parameters for
each effect, as shown in the table below.
5. Using the MIX control, adjust the mixing balance of dry
and effect signals fed from the appropriate OUTPUT jacks.
TYPE VARIATION ADJUST
PARAM.1
F 6
E G 5 7
D H 4 8
I
C 3 9
B J 2 10
11
A K 1
PEAK
3 4
2
MODE
SINGLE 1/DUAL
SW
G DELAY DISTORTION
H MISC G. MULTI 1
I CHORUS G. MULTI 2
J PITCH
K FLANGER
MODE
SINGLE 1/DUAL
SW
DELAY DISTORTION
G
H MISC G. MULTI 1
I CHORUS G. MULTI 2
J
PITCH
K FLANGER
In the single (1/2) mode, these controls and indi-
cators are not used.
MIX TYPE
DRY+EFF
DLY+REV
MODE
VOCAL DELAY
SINGLE2
PLATE MISC
SINGLE1 DUAL
ROOM CHO
S.HALL PITCH
DRY EFF
L.HALL FLANGE
PEAK
5
1
<About PEAK indicator>
The PEAK indicator on the front panel illuminates when
the input signal to be monitored reaches 6 dB below the
clipping level. Adjust the input level appropriately so
that the PEAK indicator occasionally flickers.
If you hear the output sound distorted though the PEAK
indicator does not steadily light or illuminate so often,
it may be due to the signal level increase in the effect
processing. In such a case, reduce the input level so that
the output sound is not distorted.
SINGLE 2
<Note on changing the switch position>
When you change the position of the MODE, EFFECT TYPE,
or VARIATION switch, the DE-10 resets the internal DSP
B. MULTI
and the output signal disappears momentarily. This is
VO. MULTI
due to not a malfunction.
<Notes on using the ADJUST and MIX controls>
• When you turn the ADJUST or MIX control, a click may
SINGLE 2
be generated with some effect type.
• If the default of a parameter is the maximum or
B. MULTI minimum value, you cannot increase or decrease the
VO. MULTI
value using the ADJUST control, respectively.
20
EFFECT 2
VARIATION ADJUST MIX
PARAM.2 PARAM.3
DRY+EFF
6
7
5
4 8
9
3
10
2
DRY EFF
1 1 1
4 4
EFF MUTE
POWER