Page 2
This product, including software and documentation, is the property of Supermicro and/or its licensors, and is supplied only under a license. Any use or reproduction of this product is not allowed, except as expressly permitted by the terms of said license.
Safety Information and Technical Specifi cations Table of Contents Contacting Supermicro ..................iv Returning Merchandise for Service..............v Chapter 1 Safety Guidelines ESD Safety Guidelines ................... 1-1 General Safety Guidelines ................1-1 An Important Note to Users ................1-2 Introduction to the SAS-113TQ Backplane ............. 1-2 Chapter 2 Connectors, Jumpers and LEDs Front Connectors ....................
Super Micro Computer, Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. Tel: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.com (Technical Support) Web Site: www.supermicro.com Europe Address: Super Micro Computer B.V. Het Sterrenbeeld 28, 5215 ML...
For faster service, RMA authorizations may be requested online (http://www. supermicro.com/support/rma/). Whenever possible, repack the backplane in the original Supermicro box, using the original packaging materials. If these are no longer available, be sure to pack the backplane in an anti-static bag and inside the box. Make sure that there is enough packaging material surrounding the backplane so that it does not become damaged during shipping.
Safety Information and Technical Specifi cations Chapter 1 Safety Guidelines To avoid personal injury and property damage, carefully follow all the safety steps listed below when accessing your system or handling the components. ESD Safety Guidelines Electrostatic Discharge (ESD) can damage electronic com ponents. To prevent dam- age to your system, it is important to handle it very carefully.
This manual refl ects SAS-113TQ Revision 1.02, the most current release available at the time of publication. Always refer to the Supermicro Web site at www.supermi- cro.com for the latest updates, compatible parts and supported confi gurations.
SAS-113TQ Backplane User's Guide Front Connector and Pin Defi nitions #1. Backplane Main Power Connectors Backplane Main Power The 4-pin connectors designated JP10, provide 4-Pin Connector power to the backplane. See the table on the Pin# Defi nition right for pin defi nitions. +12V 2 and 3 Ground...
Page 10
Safety Information and Technical Specifi cations #6 and #7. I C Connectors C Connector Pin Defi nitions The I C Connectors, designated JP44 and Pin# Defi nition JP45, are used to monitor HDD activity and Data status. See the table on the right for pin Ground defi...
Safety Information and Technical Specifi cations C and SGPIO Modes and Jumper Settings This backplane can utilize I C or SGPIO. SGPIO is the default mode and can be used without making changes to your jumpers. The following information details which jumpers must be confi...
SAS-113TQ Backplane User's Guide Rear Connectors and LED Indicators SAS #1 SAS #5 SAS #3 ACT#3 ACT#3 27 27 33 33 21 21 FAIL#1 FAIL#1 J2 J2 J4 J4 ACT#0 ACT#0 ACT#2 ACT#2 C106 C106 ACT#6 ACT#6 J1 J1 27 27 33 33 21 21 FAIL#0...
Page 14
Safety Information and Technical Specifi cations Notes...
Page 15
SAS-113TQ Backplane User's Guide Disclaimer (cont.) The products sold by Supermicro are not intended for and will not be used in life sup- port systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical systems whose failure to per- form be reasonably expected to result in signifi...