Shure ULX-D User Manual page 13

Locking Controls and Settings
Use the feature to prevent accidental or unauthorized changes to the
LOCK
hardware.
Receiver
Menu path: >
DEVICE UTILITIES
Use the control wheel to select and lock any of the following receiver
functions.
• : All menu paths are inaccessible
MENU
• : Gain adjustment is locked
GAIN
• : Power switch is disabled
POWER
• : Cannot perform a Scan and Sync
SCN/SYC
Tip: To unlock, press the
EXIT
, and then press
UNLOCKED ENTER
Transmitter
Menu path: >
UTILITY LOCK
Use the transmitter controls to select and lock any of the following
transmitter functions.
• : All menu paths are inaccessible.
MENU LOCK
• : Power switch is disabled
POWER LOCK
Quick-Lock Option: To turn on the transmitter with its power and menu
navigation buttons locked, press and hold the ▲ button during power-on until
the locked message is displayed.
Tip: To unlock the
MENU LOCK
through the following screens:
UTILITY
To unlock the , set the power switch to the
POWER LOCK
press and hold the ▲ button while resetting the power switch to the
position.
Encryption
ULX-D features Advanced Encryption Standard (AES-256) to ensure that
only the receiver that is keyed to the transmitter can monitor the audio
content.
Note: When enabled, encryption is applied to all receiver channels.
Encryption does not affect Dante audio signals, audio quality, or channel
spacing.
1. Enable encryption on the receiver:
The encryption symbol illuminates and the LCD displays
.
ENCRYPTION
2. Sync the transmitter to the receiver. The encryption symbol displays on
the transmitter.
Note: Any change to the encryption status on the receiver such as enabling/
disabling encryption or requesting a new encryption key, requires a sync
to send the settings to the transmitter.
will display on the receiver LCD panel if the transmitter and receiver do not
share the same encryption key.
LOCK
button, turn the control wheel to select
to save.
, press the button 4 times to pass
ENTER
> >
LOCK MENU UNLOCK
position, then
off
>
DEVICE UTILITIES ENCRYPTION
SYNC NOW FOR
ENCRYPTION MISMATCH
Custom Groups
Use this feature to create and export up to 6 groups of manually selected
frequencies to networked receivers prior to a group scan to simplify system
set up.
Tip: Use Wireless Workbench or Wireless Frequency Finder to select the
best compatible frequencies. See www.shure.com for more information.
To create a custom group:
>
GROUPS SETUP
Use the control wheel to choose group, channel and frequency values.
Press
ENTER
Prior to performing a group scan, export a custom group to networked
receivers:
1. Go to
DEVICE UTILITIES
2. Press the flashing
receivers on the network.
Note: Use the
System Reset
System Reset clears the current receiver settings and restores the factory
default settings.
To restore factory default settings:
1. Go to
DEVICE UTILITIES
2. Scroll to the
3. Press the flashing
settings.
on
RF Cascade Ports
The receiver has 2 RF cascade ports on the rear panel to share the signal
from the antennas with 1 additional receiver.
Use a shielded coaxial cable to connect the RF cascade ports from the first
receiver to the antenna inputs of the second receiver.
Important! The frequency band must be the same for both receivers.
.
Antenna Bias
Antenna ports A and B provide a DC bias to power active antennas. Set the
DC power to off when using passive (non-powered) antennas.
To turn bias off:
warning
DEVICE UTILITIES
to save.
> >
ADVANCED RF
button to export all custom groups to all
ENTER
option to remove all custom group settings.
CLEAR ALL
> >
SYSTEM RESET
option and press
DEFAULT SETTINGS
button to return the receiver to the default
ENTER
>
DEVICE UTILITIES ADVANCED RF
> >
ADVANCED RF CUSTOM
>
CUSTOM GROUPS EXPORT
.
RESTORE
.
ENTER
> >
ANTENNA BIAS OFF
13