Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for AOpen AOI-892
Summary of Contents for AOpen AOI-892
-
Page 1: Quick Installation Guide
Quick Installation Guide AOI-892 IEEE 802.11g Wireless Broadband Router... -
Page 2: Getting Started
Quick Installation Guide Getting started This is a step-by-step instruction on how to start using the router and get connected to the Internet. 1) Setup your network as shown in the setup diagram below. 2) You then need to set your LAN PC clients so that it can obtain an IP address automatically. By default the Broadband Router’s DHCP server is enabled so that you can obtain an IP address automatically. -
Page 3: Quick Setup
<OK> to login. Note: By default the user name is “admin” and the password is “1234”. For security reasons it is recommended that you change the password as soon as possible (in General setup/system/password, see chapter 2) Select the section (Quick Setup Wizard, General Setup, Status Information and Tools) you wish to configure and proceed to the corresponding chapter. - Page 4 Parameter Description Set Time Zone Select the time zone of the country you are currently in. The router will set its time based on your selection. Time Server Address You can manually assign time server address if the default time server does not work. Enable Daylight Savings The router can also take Daylight savings into account.
-
Page 5: Step 2) Broadband Type
Click on NEXT to proceed to the next page (step 2) Broadband Type. Step 2) Broadband Type In this section you have to select one of the four types of connections that you will be using to connect your broadband router’s WAN port to your ISP (see screen below). Note: Different ISPs require different methods of connection to the Internet. - Page 6 1.4 PPTP Your ISP requires you to use a Point-to-Point Tunneling Protocol (PPTP) connection. 1.5 L2TP Your ISP requires you to use a Layer Two Tunneling Protocol (L2TP) connection. 1.6 Telstra Big Pond This Protocol only used for Australia’s ISP connection. Click on one of the WAN types and then proceed to the manual’s relevant sub-section .
-
Page 7: Parameters Description
Parameters Description Host Name If your ISP requires a Host Name, type in the host name provided by your ISP. Otherwise leave it blank if your ISP does not require a Host Name. MAC Address Your ISP may require a particular MAC address in order for you to connect to the Internet. - Page 8 1.2 Fixed-IP xDSL Select Fixed-IP xDSL if your ISP has given you a specific IP address for you to use. Your ISP should provide all the information required in this section. Parameters Description This is the IP address that your ISP has given you. Gateway IP This is the ISP’s IP address gateway.
- Page 9 1.3 PPPoE Select PPPoE if your ISP requires the PPPoE protocol to connect you to the Internet. Your ISP should provide all the information required in this section. Parameter Description User Name Enter the User Name provided by your ISP for the PPPoE connection.
- Page 10 not wish to set a maximum packet size. Connection Type If you select “Continuous”, the router will always connect to the ISP. If the WAN line breaks down and links again, the router will auto-reconnect to the ISP. If you select “Connect On Demand”, the router will auto-connect to the ISP when someone wants to use the Internet and keep connected until the WAN idle timeout.
- Page 11 1.4 PPTP Select PPTP if your ISP requires the PPTP protocol to connect you to the Internet. Your ISP should provide all the information required in this section. Parameter Description Obtain an IP address The ISP requires you to obtain an IP address by DHCP automatically before connecting to the PPTP server.
- Page 12 Gateway Enter the IP address of the ISP Gateway. User ID Enter the User Name provided by your ISP for the PPTP connection, sometimes called a Connection ID. Password Enter the Password provided by your ISP for the PPTP connection. PPTP Gateway If your LAN has a PPTP gateway, then enter that PPTP gateway IP address here.
- Page 13 1.5 L2TP Select L2TP if your ISP requires the L2TP protocol to connect you to the Internet. Your ISP should provide all the information required in this section. Parameter Description Obtain an IP address The ISP requires you to obtain an IP address by DHCP automatically before connecting to the L2TP server.
- Page 14 Use the following IP address The ISP gives you a static IP to be used to connect to the L2TP server. IP Address This is the IP address that your ISP has given you to establish a L2TP connection. Subnet Mask Enter the Subnet Mask provided by your ISP (e.g.
-
Page 15: Telstra Big Pond
again, the router will not auto-connect to the ISP. Idle Time Out The WAN "idle timeout" auto-disconnect function may not work due to abnormal activities of some network application software, computer virus or hacker attacks from the Internet. For example, some software sends network packets to the Internet in the background, even when you are not using the Internet. - Page 16 Parameter Description User Name Enter the User Name provided by your ISP for the Telstra Big Pond connection. Password Enter the Password provided by your ISP for the Telstra Big Pond connection. User decide login server Select if you want to assign the IP of Telstra Big Pond’s login manually server manually.