Display; Calling Up Menu Addresses - YOKOGAWA Dpharp vigilantplant EJA Series User Manual

2.2.2 Display

The HART communicator searches for a transmitter on
the 4 to 20mA loop when it is turned on. When the
HART communicator is connected to the transmitter,
Online menu (Top menu) is started automatically and
the following display appears. If no transmitter is
found, you select Online menu.
Manufacturer's
transmitter type
Tag (8 Characters)
EJA :YOKOGAWA
Online
<b>
1 Device setup
2 Pres
<c>
3 A01 Out
4 LRV
<d>
5 URV
<e>
Function keys
Pressing one of the SHIFT keys makes the arrow
mark corresponding to the pressed key appear.
Appears when the voltage level of the battery is low.
Figure 2.2.2 Display
<a> appears and flashes during communication
between the HART communicator and the
transmitter. At Burst mode,
<b> The menu items selected from the previous menu.
<c> The items to be used from the menu of <b>.
<d> or appears when the item is scrolled out of
the display.
<e> The labels of function corresponding to each
function key appears. These labels reflect cur-
rently available choices.

2.2.3 Calling Up Menu Addresses

Subsection 2.3.2 shows the configuration of all menu
items available with the HART communicator. The
desired item can be displayed with ease by understand-
ing the menu configuration.
When the HART communicator is connected to the
transmitter, Online menu will be displayed after power
is turned on. Call up the desired item as follows:
<a>
0.13 mmH2O
4.001 mA
0.00 mmH2O
3000.00 mmH2O
The highlighting cursor
F0203.EPS
appears.
2. HART COMMUNICATOR OPERATION
Function Key Labels
F1 F2
HELP ON/OFF
access on-line activates or
help deactivates a
binary variable
RETRY DEL
try to re- delete current
establish character or Hot
communication Key Menu item
EXIT SEND
leave the send data to
current menu device, or mark
data to send
YES PGUP
answer to move up one
yes/no question help screen
ALL PREV
include current go to previous
Hot Key item on message in a
Hot Key Menu list of messages
for all devices
SAVE EDIT
save information edit a variable
to value
communicator
SEND ADD
send data to add current item
device, or mark to Hot Key
data to send Menu
Key Operation
There are two choices to select the desired menu item.
1. Use the or
and then press the
2. Press the number displayed for the desired item.
• To return to the previous display, press the
* If ,
ABORT ESC
press the desired function key.
Example: Call up the Tag item, to change the tag.
Check to see where item Tag is located in the menu
configuration. Then, call up Tag item on the display
according to the menu configuration.
Device setup
Pres
P01 Out
LRV
URV
Tag
Unit
Re-range
Device information
.
.
.
2-3
F3
ABORT
terminate acknowledge
current task information on
screen
ESC ENTER
leave value accept user-
unchanged entered data
QUIT NEXT
terminate session leave the
because of a current menu
comunication
error
PGDN
move down one answer to
help screen yes/no question
NEXT
go to next do not mark
message in the variable to be
list of messages sent in off-line
configuration
HOME
go to the top include Hot Key
menu in the item for one
device device
description
BACK
go back to
menu from
which HOME
was pressed
key to select the desired item,
key.
and are displayed,
EXIT
Process variables
Diag/Service
Basic Setup
Detailed Setup
Review
EJA:YOKOGAWA
Tag
YOKOGAWA
YOKOGAWA
HELP DEL ESC
IM 01C22T01-01E
F4
OK
NO
SKIP
ONE
F0204.EPS
key.
ENTER