3D Video - Mitsubishi Electric DLP 742 Series Basic Owner's Manual

3D Video

Emitters for controlling 3D glasses are as follows.
742 Series: Internal IR emitter, Internal DLP Link
Signal, or Optional External emitter.
842 Series: Internal Bluetooth ® RF, Internal DLP Link
Signal, or Optional External emitter.
• Active-shutter 3D glasses compatible with any one
of the following:
- The TV's internal emitters
- DLP link
- A matching external synchronization emitter
connected to the TV's back panel
For 742 Series: Glasses compatible with the TV's IR
internal (742 Series) emitters are:
- XPAND model 3DG-X103 IR glasses made for
Mitsubishi 3D TVs
- XPAND model X103 Universal IR glasses
For 842 Series: Glasses compatible with the TV's
internal Bluetooth ® RF emitters are:
- Refer to the company website for the recom-
mended 3D glasses.
For all models:
- All glasses made to use the DLP link system
For more information, visit the 3D TV page at
www.mitsubishi-tv.com.
• A compatible 3D source device connected to the
TV via HDMI or StreamTV Internet and outputting a
3D signal in one of these formats:
- Frame Packing 1080p@24 Hz or 720p@60 Hz
Off
• Turns off 3D images; displays 3D content
as 2D (you may see two images).
• Restores normal TV adjustment options
when viewing an ordinary 2D signal.
Automatic
HDMI HDMI
• Switches the TV to 3D mode and selects the
correct 3D format when the TV detects a 3D
2 2
1 1
signal from an HDMI 1.4a-compliant device
or a 3D movie from VUDU Movies.
• Automatically switches the TV out of 3D
mode when receiving a normal 2D signal.
Use the Picture > 3D Mode
menu to enable 3D video.
3 3
Choice of Source Formats
If your device is not HDMI 1.4a
compliant, you must choose the
correct setting from this list.
3. TV Features
Using the TV's Internal Emitters
16 ft.
20°
25 ft.
20°
16 ft.
25 ft.
- Side-by-Side(Half) 1080p@24/30/60 Hz,
1080i@60 Hz, or 720p@60 Hz
- Top-and-Bottom 1080p@24/30/60 Hz or
720p@60 Hz
- Checkerboard 1080p@60 Hz (lower resolutions
may be supported but will not fill the screen)
Initial Setup
1.
If your 3D glasses came with a synchronization emitter,
connect the unit to the 3D GLASSES EMITTER jack.
Place the emitter at the front of the TV where there is a
clear path to the glasses.
Note: No emitter is required if using the TV's internal
emitters or DLP Link.
3D 3D
ANT
GLASSES GLASSES
EMITTER EMITTER
3D 3D
ANT
HDMI HDMI GLASSES GLASSES
EMITTER EMITTER
1 1 2 2 3 3
Connecting an external emitter
2.
Power on the TV and the source device.
3.
Connect the source device to the TV's HDMI input.
4.
When the New Device Found screen displays,
name the input.
5.
Press EXIT to close the New Device Found screen.
Depth
Adjusts the simulated 3D effect
applied to a 2D image. Available
only when Source Format is set
to 2D+ Depth.
For assistance call 1(800) 332-2119
Typical effective range
of the emitters in the
vertical and horizontal
planes.
Ranges can be affected
by room lighting and
glasses brand and
model.
35°
35°
16 ft.
DIGITAL
AUDIO
OUTPUT
L
R
DIGITAL
AUDIO
OUTPUT
L
R
21