Advertisement
Quick Links
Sharp Installation
PROJECTOR COMMUNICATIONS KIT
PLEASE READ THIS DOCUMENT FOR IMPORTANT
THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:
Kit Type: SHARP
Included Communications Adapter(s):
Quantity
1
1
THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING
COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER'S VARIOUS
MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS
INDICATED BY THE " " IN THE "Config as" COLUMN. IF YOUR PROJECTOR MODEL
DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER
WITH THE CORRECT SETTINGS.
PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND
SIGNAL CONNECTION INSTRUCTIONS.
THIS SWITCHER HAS BEEN CONFIGURED FOR:
Config
Model
as
XG (RS-232)
XG-E1200U
XG-1000/E1100
XG-NV6/NV2U/NV5
XG-NV3
XG-P10XU
PG-C30XU
XG-P20XU
Extron • System 8/10 P
LUS
SYSTEM 8/10 Plus
ATTENTION!
INSTALLATION INSTRUCTIONS
Part Number
26-426-01
26-467-01
Rotary Switches Cable
RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter
0
0
F
1
0
F
0
0
F
2
0
F
1
0
F
2
0
F
2
0
F
1
0
F
• User's Manual • P/N 68-409-01 Rev. C
Configuration and Connections
Description
ADP, SHARP IR
ADP, UNV, "A"
SHARP XG (RS-232)
SW15 Settings
9
J2
3
J2
3
J2
9
J2
9
J2
9
J2
9
J2
9
J2
Comm
26-467-01
26-426-01
26-426-01
26-467-01
26-467-01
26-467-01
26-467-01
26-467-01
Page 1
Advertisement
Related Manuals for Extron electronics SYSTEM 8/10 Plus
Summary of Contents for Extron electronics SYSTEM 8/10 Plus
-
Page 1: Installation Instructions
Sharp Installation Configuration and Connections SYSTEM 8/10 Plus PROJECTOR COMMUNICATIONS KIT ATTENTION! PLEASE READ THIS DOCUMENT FOR IMPORTANT INSTALLATION INSTRUCTIONS THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS: Kit Type: SHARP Included Communications Adapter(s): Quantity Part Number Description 26-426-01... - Page 2 The general setup is explained on page 3-4 of your System 8/10 Plus User’s Manual. 1. Use a small screwdriver to remove the access cover from the System 8/10 Plus front panel. Refer to page 3-3 of the User’s Manual.
- Page 3 Configuration and Connections System 8/10 Plus to Sharp XG Series Projector Connections (RS-232) Use the illustration below as a guide when connecting the System 8/10 Plus to a Sharp projector. Refer to Sharp documentation to continue the installation. ________ Important note! For Sharp projectors which do not allow simultaneous...
- Page 4 Verify that the System 8/10 P is already configured for the Sharp projector. The general setup is explained on page 3-4 and the switch settings for the Sharp projector are repeated below. 1. Use a small screwdriver to remove the access cover from the System 8/10 P front panel.
- Page 5 Sharp Installation Configuration and Connections Sharp XG-1000/E1100 Projector Connections Use the illustration below when connecting the System 8/10 P to a Sharp XG- 1000/E1100 projector. Refer to Sharp documentation to continue the installation. Filter AUDIO VIDEO S-VIDEO WIRED INPUT REMOTE...
- Page 6 The general setup is explained on page 3-4 of your System 8/10 Plus User’s Manual. 1. Use a small screwdriver to remove the access cover from the System 8/10 Plus front panel. Refer to page 3-3 of the User’s Manual.
- Page 7 Sharp Installation Configuration and Connections System 8/10 Plus - Sharp XG-E1200U LCD Projector Cable Diagram Use the illustration below as a guide when connecting the System 8/10 Plus to a Sharp XG-E1200U projector. Refer to Sharp documentation to continue the installation.
- Page 8 The general setup is explained on page 3-4 of your System 8/10 Plus User’s Manual. 1. Use a small screwdriver to remove the access cover from the System 8/10 Plus front panel. Refer to page 3-3 of the User’s Manual.
- Page 9 Configuration and Connections System 8/10 Plus - Sharp NV6 Projector Connections Use the illustration below as a guide when connecting the System 8/10 Plus to a Sharp NV6 projector. Refer to Sharp documentation to continue the installation. ________ Important note! When connecting the Switcher’s BNC output to either the projector’s BNC or 15-pin input (but not both simultaneously), set the projector’s...
- Page 10 The general setup is explained on page 3-4 of your System 8/10 Plus User’s Manual. 1. Use a small screwdriver to remove the access cover from the System 8/10 Plus front panel. Refer to page 3-3 of the User’s Manual.
- Page 11 Configuration and Connections System 8/10 Plus - Sharp NV3 Projector Connections Use the illustration below as a guide when connecting the System 8/10 Plus to a Sharp NV3 projector. Refer to Sharp documentation to continue the installation. ________ The Sharp NV3 projector does not allow simultaneous connections to S-Video...