Page 2
WARNING: When using electrical products, basic cautions should always be followed, including the following: 1. Read these instructions. 2. Keep these instructions safe. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7.
Page 3
ATTENTION: L’utilisation de tout appareil électrique doit être soumise aux precautions d’usage incluant: 1. Lire ces instructions 2. Gardez ce manuel pour de futures références. 3. Prétez attention aux messages de précautions de ce manuel. 4. Suivez ces instructions. 5. N’utilisez pas cette unité proche de plans d’eau. 6.
Page 4
ACHTUNG: Beim Einsatz von Elektrogeräten müssen u.a. grundlegende Vorsichtsmaßnahmen befolgt werden: 1. Lesen Sie sich diese Anweisungen durch. 2. Bewahren Sie diese Anweisungen auf. 3. Beachten Sie alle Warnungen. 4. Befolgen Sie alle Anweisungen. 5. Setzen Sie dieses Gerät nicht in der Nähe von Wasser ein. 6.
Page 5
CUIDADO: Cuando use productos electrónicos, debe tomar precauciones básicas, incluyendo las siguientes: 1. Lea estas instrucciones. 2. Guarde estas instrucciones. 3. Haga caso de todos los consejos. 4. Siga todas las instrucciones. 5. No usar este aparato cerca del agua. 6.
4, 8 or 16 Ohms Per Channel: Passive Bass, Mid, Treble with switchable Deep, Mid Shift & Treble Shift Master Section: Dynamics & Tone Reverb Laney-designed digital reverb Features 4 x 12AX7/ECC83 preamp tubes 4 x 12AX7/ECC83 preamp tubes 4 x 6L6 output tubes...
Page 9
IRONHEART. With molten metal flowing through its circuits, IRONHEART continues the legacy passed on by previous Laney amps such as KLIPP and AOR, and hits you hard between the eyes like a power hammer from hell. When cranked, the IRONHEART possesses massive amounts of gain, but is equally at home providing smooth rock and clean tones.
FRONT PANEL CONTROLS (Pull Deep) (Pull Shift) (Pull Shift) 1. INPUT 1/4" mono jack socket. Connect your guitar here. Use only a good quality instrument cable. 2. PRE-BOOST SWITCH Switches the input boost circuit on or off. The Pre-Boost circuit increases the input signal to the preamp tubes, just like placing a boost pedal in your signal path.
Page 11
20. REVERB Controls the level of the built in Laney-designed digital reverb. 21. WATTS The Watts control adjusts the signal level within the power amplifier, allowing it to be driven harder at lower volume levels. For full output power, running the power tubes at maximum levels, turn this control fully clockwise.
REAR PANEL CONTROLS L Z B 1 2 3 4 1. MAINS INLET SOCKET Connect to your power source. Make sure the voltage indicated on the rear panel is correct for your country! 2. MAINS FUSE This drawer contains the main safety fuse for the unit. The fuse protects the amplifier from damage in the event of fault by disconnecting the mains power supply.
Page 13
REAR PANEL CONTROLS 5. FX RETURN 1/4" mono jack socket for the connection of the output of an external FX unit. This can also be used as a slave in for the power amp. As the FX Loop is an insert type, this will mute the preamp signal. 6.
QUICK START SETTINGS Set to preference Clean (Pull Deep) (Pull Shift) (Pull Shift) Lead Rock (Pull Deep) (Pull Shift) (Pull Shift) Rhythm Lead Metal (Pull Deep) (Pull Shift) Rhythm Lead Detuned (Pull Shift) (Pull Shift) Metal Rhythm...
Page 16
TUBE AMP TIPS Tube amplifiers generally sound much warmer/sweeter than solid state transistor amplifiers but they also need a little more respect due to the fragile glass tubes. The Ironheart heads use four 12AX7 preamp tubes, and two or four 6L6 output tubes (depending on the model) which should give you years of trouble free service, however like all tube amps;...
BLOCK DIAGRAM LINE OUT FX SEND FX RETURN LEAD/RHYTHM BYPASS 0 dBu -10dBu INPUT LEAD Pre-Boost LEAD VOLUME LEAD GAIN REVERB REVERB RHYTHM LEVEL GAIN CLEAN/RHYTHM CLEAN VOLUME RHYTHM VOLUME CLEAN/RHYTHM 16Ohms 8Ohms/2x16Ohms Master section controls 4Ohms/2x8Ohms EXTERNAL LOUDSPEAKER 4-16 OHMS *IRT120H ONLY...