Advertisement
Advertisement
Table of Contents
Related Manuals for Laney LC50-112
Summary of Contents for Laney LC50-112
-
Page 6: Before Switching On
BEFORE SWITCHING ON... -
Page 7: Specifications
SPECIFICATIONS Supply Voltage ~100V, ~120V, ~230V, ~240V 50/60Hz Factory Option Mains Fuse (~220V>240V = T2A L 250V) (~100>120V = T5A L 250V) HT Fuse T500mA L Power Consumption 100W Output Power Rating Loudspeaker 12” Celestion 8 Ohms Loudspeaker outputs Extension speaker socket (Minimum 8 Ohm Impedance) Features Pure Class A/B Valve tone... - Page 8 INTRODUCTION Page 8 / 20...
- Page 9 Your LC50-112 should give you years of trouble-free amplification, however please take time to read this manual and familiarise yourself with the controls as it will allow you to get the best from your amplifier. We hope you enjoy using your LC50-112 as much as we enjoyed designing and making it.
-
Page 10: Front Panel Controls
Laney FRONT PANEL CONTROLS LC50 CLEAN CHANNEL DRIVE CHANNEL MASTER INPUT GAIN BRIGHT BASS VOLUME CHANNEL MODERN BASS VOLUME TONE STANDBY POWER MIDDLE TREBLE DRIVE MIDDLE TREBLE REVERB HI INPUT: ‘Hi’ stands for high gain. This input is designed for the connection of low output level guitars making it well suited for guitars with single coiled or low gain humbucker type pickups. -
Page 11: Drive Led
Switch in to enable the 'Drive' channel. (This switch must be in the disengaged position in order for the drive to be switched remotely via a foot switch.) DRIVE LED: This led will illuminate when the Drive channel is activated with the Drive switch (8) or an optional Laney FS2 remote footswitch. DRIVE: Sets the level of tube preamplifier drive or how dirty your sound is. -
Page 12: Rear Panel Controls
REAR PANEL CONTROLS Spare power fuse included in the tray. POWER INLET SOCKET: Connect to your power source. Make sure the specified voltage is correct for your country! POWER FUSE: This drawer contains the main safety fuse for the unit. The fuse protects the AC power to the amplifier. USE ONLY THE CORRECT SIZE AND RATING OF FUSE AS SPECIFIED ON THE PANEL. - Page 13 EXTENSION CABINET: Use to connect an 8-16 ohm extension cabinet. Please note mismatched impedance will reduce the amplifiers performance and in some cases may cause damage to your amplifier. Try the L 5 -112 into a Laney extension cabinet - you will be amazed what this baby cranks out.
- Page 14 QUICK START SETTINGS - suggestions only, experiment! LC50 CLEAN CHANNEL DRIVE CHANNEL MASTER INPUT GAIN BRIGHT BASS MIDDLE TREBLE VOLUME CHANNEL DRIVE MODERN BASS MIDDLE TREBLE VOLUME TONE REVERB STANDBY POWER CLEAN LC50 CLEAN CHANNEL DRIVE CHANNEL MASTER INPUT GAIN BRIGHT BASS MIDDLE...
- Page 15 USER SETTINGS - Store your own cool sounds LC50 CLEAN CHANNEL DRIVE CHANNEL MASTER INPUT GAIN BRIGHT BASS MIDDLE TREBLE VOLUME CHANNEL DRIVE MODERN BASS MIDDLE TREBLE VOLUME TONE REVERB STANDBY POWER LC50 CLEAN CHANNEL DRIVE CHANNEL MASTER INPUT GAIN BRIGHT BASS MIDDLE...
- Page 16 • Tube amplifiers; generally sound much warmer/sweeter than solid state transistor amplifiers but they also need a little more respect due to the fragile glass tubes themselves. The LC50-112 uses top quality tubes, which should give you years of trouble free service, however like all tube amps;...
-
Page 17: Block Diagram
all system parts have stabilised; usually a couple of seconds. Similarly when turning off your system always turn down the Volume controls on your guitar amplifier and then turn off its power before turning off other equipment. • Servicing: The user should not attempt to service these products. Refer all servicing to qualified service personnel. RT030 ECC83 Hi Grade 005570 V2,3... - Page 18 LC50-112 SAMPLE SYSTEMS FX Controller Laney Laney Power To The Music Power To The Music RB115 RB115 GS412A Model Model Power Rating 300W Program Power Rating 300W Program Serial Number: Serial Number: Input Input Link Link ESIGNED IN THE ESIGNED IN THE...
- Page 19 NOTES Page 19 / 20...