BEFORE USE COMPONENTS THANKS FOR PURCHASING A HAIER PRODUCT Please read these instructions carefully before using this appliance. The instructions contain important information which will help you get the best out of the appliance and ensure safe and proper installation, use and maintenance.
BEFORE USE PREPARATION PREPARING THE MACHINE Remove all the packing materials to prevent unsteadiness, including the polystyrene base. Upon opening the package, water drops may be seen on the plastic bag and the porthole. This is normal phenomenon resulting from water tests in the factory. DESCRIPTION This diagram may be slightly different from the layout of the washing machine you have just purchased due to technical improvements.
BEFORE USE SAFETY INSTRUCTIONS BEFORE SWITCHING THE APPLIANCE ON FOR THE FIRST TIME DO ... DO NOT ..Make sure that the transport bolt are removed..Touch or use the appliance when barefoot or with wet or ... Use a separate earthed socket for the power supply. damp hands or feet.
BEFORE USE INSTALLATION DISMANTLE THE TRANSPORTATION BOLTS The transportation bolts are designed for clamping anti-vibration components inside of the washing machine during the transportation process. Remove the back cover. Remove the four bolts on the rear side and take out the synthetic stabilisers from within the machine.
Page 7
BEFORE USE INLET HOSE 1. Connect the nut on the inlet hose to the connector on the water valve. 2. Apply inlet hose to a water tap with cold, fresh water. Note: Use the hose-set supplied with the appliance. Old hose-sets should not be reused.
BEFORE USE CONTROL PANEL I HG E DC y l i Wash Temp. c i t Power Rinse Speed c i l eans y Care Spin Start/pause I n tense E n d Delay Prewash Rinse Hold L M N washing button Display screen Power Switch...
Page 9
BEFORE USE Display _Display washing time, remaining time, times of rinsing, spinning time, temperature setting value, speed setting screen value, child lock state, door lock state, washing progress and alarm message, etc. Washing time Press the “Wash” button to set washing time. Press and hold this button to change the time continuously. Click this button up until the end.
USING THE APPLIANCE PROGRAM SELECTION PROGRAM MODES 1 Detergent compartment for prewash mode 2 Detergent compartment 3 Compartment for softener and other additives Temperature Recommended Preset spin speed Program Maximum Preset Laundry ¬ Hand Wash - - to 40 °C 30°C Cotton fabrics 800 rpm ¬...
TECHNICAL DATA HW80-B1286-F/HW80-B1486-F HW70-B1286-F/HW70-B1486-F 220 - 240V~/50Hz Power source 220 - 240V~/50Hz Max. working current (A) Water pressure (MPa) 0.03≤P ≤1...
USING THE APPLIANCE WASHING METHODS PLEASE NOTE This washing machine is for domestic use only. If the machine is use for commercial purpose the guarantee will not be valid anymore.Do not use it for purposes other than that for which it was designed. Follow the instructions given on the label of each garment and wash only machine-washable garments.
Page 13
USING THE APPLIANCE LOADING THE MACHINE Heavy Delicate Wash Temp. Silk Sport wash Wool Silent Rinse Speed Synthetic Quick Power Memory Spin Spin Auto Cotton Self-clean Start / Pause Strong wash Delay Pre-wash Soak Press and hold 2seconds to set door unlocked Open the washer door, put in the laundry piece by piece.
Page 14
USING THE APPLIANCE SETTING WASHING TEMPERATURE Temp. t é Lavage Temp. Lavage Marche / Arrêt Mixte Express15' Vitesse Rinçage Rinçage Vitesse é c i l Power Laine Bébé coton Press and hold down the temperature button until the desired temperature is selected . Essorage M emo Essorage...
Page 15
USING THE APPLIANCE CARE CHART Resistant material Bleachable in cold water Don't dry clean Delicate fabric Do not bleach Dry fl at Washable at 95 °C Iron at 200 °C Hung to dry Washable at 60 °C Iron at 150 °C Dry on clothes hanger Washable at 40 °C Iron at 100 °C...
M A I N T E N A N C E CLEANING & CARE AFTER WASHING Turn off the water supply and pull out electricity plug after each wash. Open the washer door to prevent formation of moisture and odours. If the washing machine is left idle for a long period, drain the water in the machine and replace the drain hose.
Page 17
MAINTENANCE WATER INLET VALVE AND INLET VALVE FILTER To prevent blockage to the water supply by ingress of foreign substances, clean the water inlet valve and inlet valve filter regularly. MOVING THE MACHINE If the machine is to be moved to a distant location, replace the transportation bolts removed before installation to prevent damage as shown below.
MAINTENANCE DISPLAY CODES DISPLAY CODES AND SPECIAL FUNCTIONS CODES CAUSES SOLUTIONS Err1 ¬ Door is not properly shut. _ Shut the door properly and then press the Start/Pause button. Err2 ¬ Drainage error, water not emptied within 6 _ Clean the filter and check the drain hose for blockage. If error minutes.
MAINTENANCE TROUBLESHOOTING TROUBLESHOOTING The following circumstances do not constitute problems. Do not contact the Service Center until the problem has been confi rmed. PROBLEM CAUSES SOLUTIONS Washing machine fails to ¬ Poor connection to the power supply. _ Check connection to the power supply. operate.