Unpacking When unpacking, check to make sure the product is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. For technical questions, please call 1-800-444-3353;...
Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. Protective, electrically nonconductive clothes and nonskid footwear are recommended when working. Wear restrictive hair covering to contain long hair. REV 04/06 For technical questions, please call 1-800-444-3353; SKU 93205 Page 3 Troubleshooting section at end of manual.
Page 4
Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools. Do not operate tool if under the influence of alcohol or drugs. Read warning labels if taking prescription medicine to determine if your judgement or reflexes are impaired while taking drugs.
Page 5
For technical questions, please call 1-800-444-3353; SKU 93205 Page 5 Troubleshooting section at end of manual.
For best service you should incorporate a regulator and inline filter, as shown in the diagram above. Hoses, couplers, regulators, and filters are all available at Harbor Freight Tools. Note: Compressor pumps discharge condensed water, oil, or other contaminants along with the compressed air.
If it appears to thin, add a very small amount of thinner (not included). BE CAREFUL when thinning. Proceed slowly, adding very minimal amounts. NEVER exceed the manufacturer’s thinning recommendations. For technical questions, please call 1-800-444-3353; SKU 93205 Page 7 Troubleshooting section at end of manual.
FIGURE 1 on page 6). By turning it counterclockwise (all the way open), the pattern will flatten. Turn the Pattern Control Knob (16) clockwise for a round pattern. See FIGURE 4 below. FIGURE 4 Flat/Open Round/Closed For technical questions, please call 1-800-444-3353; Page 8 SKU 93205 Troubleshooting section at end of manual.
Page 9
(you see globs of paint), close down the Fluid Control Knob (23) slowly, checking the mixture after each adjustment. See FIGURE 5 below. FIGURE 5 Too Coarse Correct Too Fine (Tighten) (Loosen) For technical questions, please call 1-800-444-3353; SKU 93205 Page 9 Troubleshooting section at end of manual.
Clean out the gun thoroughly after EVERY use, according to the instructions found on the next page. For technical questions, please call 1-800-444-3353; Page 10 SKU 93205 Troubleshooting section at end of manual.
Disposal: After cleaning your Spray Gun, properly dispose of your cleaning solutions according to the solution manufacturer’s direction and local hazardous waste standards. For technical questions, please call 1-800-444-3353; SKU 93205 Page 11 Troubleshooting section at end of manual.
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. For technical questions, please call 1-800-444-3353; Page 12 SKU 93205 Troubleshooting section at end of manual.
2. Holes on one side of the Air cap are plugged. (Clean the Air cap with a nonmetallic point.) If the steps above do not solve the problem or if the repairs involved are too complex, contact a qualified technician. Page 14 For technical questions, please call 1-800-444-3353. SKU 93205...
Page 15
5. Replace Fluid Leaking from 1. Packing Nut loose 1. Tighten without restricting Packing Nut 2. Packing worn or dry 2. Replace or lubricate (non-silicone) For technical questions, please call 1-800-444-3353; SKU 93205 Page 15 Troubleshooting section at end of manual.
Page 16
90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This...