Table of Contents
Advertisement
PROGRAMME TIMER SETTING
The timer function is built into this receiver allows you to perform the
following operations:
• Three timer settings at the same time: Program-1, Program-2 and
Program-3;
• Setting of ON time and OFF time;
• Setting of source: The source can be selected from tuner preset
number 1 to 50, DVD, AUX and AUTO;
• It is possible to specify the track numbers of DVD;
• It is possible to select recording or playing media;
• Setting of single operation (ONCE) or everyday operation (DAILY).
IMPORTANT:
The timer setting with track number specified can be used only
when the system control switch is set to SYSTEM position except
with using the tuner.
In the following procedure, each button should be pressed within 5
seconds after pressing the previous button.
When the remote control is used to set the timer, press the AMP
button v to change the AMP function mode at first.
Press the power button A/ z to turn the power of the unit ON.
1.
Press the TIMER button K/⁄0 . The display indicates "TMR
2.
PROG".
TIMER
3.
[SET THE ON TIME]
3-1. After a few seconds, "PROG-1" appears and starts blinking.
Turn the JOG control M or press the cursor
select the desired timer program, and press the ENTER button
M/ n. (If the selected program was used before, the details of
the previous setting appear.)
MULTI JOG
(PUSH ENTER)
3-2. The display indicates "ON TIME" in the upper segment of the
display, and the present time is displayed in the middle
segment. (In this case, the present time is 10:05.)
3-3. "10" blinks. Turn the JOG control M or press the cursor
button n to adjust the hour. To increase, turn to the right. To
decrease, turn to the left. For example, set the hour to 12. (In
this case, AM changes to PM.)
MULTI JOG
(PUSH ENTER)
3-4. Press the ENTER button M/ n to set the hour, and the minutes
start to blink.
3-5. "05" blinks. Turn the JOG control M or press the cursor
button n to adjust the minutes. For example, set the minutes to
30. (12:30)
3-6. Press the ENTER button M/ n to set the minutes and all
segments start to blink. When all segments blink, the time can be
re-adjusted using the JOG control M or press the cursor
button n.
3-7. Press the ENTER button M/ n to complete ON time setting.
The display stops blinking.
MULTI JOG
(PUSH ENTER)
4.
4-1. "OFF TIME" then appears in the upper segment of the display,
4-2. "12" blinks. Turn the JOG control M or press the cursor
4-3. Press the ENTER button M/ n to set the time, and the minutes
4-4. Turn the JOG control M or press the cursor
4-5. All segments blink in the display. The time can be re-adjusted
5.
5-1. The display indicates "AUTO" in the middle segment.
5-2. If you want to play a specified source in AUTO mode, you have
@ #
button n to
5-3. If you want to select a source, you should select "MANUAL".
MULTI JOG
(PUSH ENTER)
6.
6-2. The display indicates the source name, for example DVD. Turn
@ #
MULTI JOG
(PUSH ENTER)
6-3. Turn the JOG control M or press the cursor
@ #
6-4. Press the ENTER button M/ n to set the track number to be
@ #
7.
7-1. Turn the JOG control M or press the cursor
MULTI JOG
(PUSH ENTER)
14
[SET THE OFF TIME]
and the time set as ON time (12:30) appears in the middle
segment.
button n to adjust the time of timer stop. For example, "1".
start to blink.
adjust the minute of timer stop, and press the ENTER button M/
n to set the minute.
MULTI JOG
(PUSH ENTER)
by turning the JOG control M or press the cursor
4-6. Press the ENTER button M/ n to complete the OFF time setting.
MULTI JOG
(PUSH ENTER)
[SET THE MANUAL or AUTO] (only in SYSTEM mode)
Note:
If "AUTO" is selected, the auto play function is activated, and it
detects the source that can be played. For example, if a disk is set
to CD side of DV2100, and no other player is set, the PS2100 will
play the CD in DV2100 automatically.
to set it.
MULTI JOG
(PUSH ENTER)
[SET TO MANUAL]
6-1. Turn the JOG control M or press the cursor
"MANUAL" and press the ENTER button M/ n. The display
indicates "MANUAL" for 2 seconds.
the JOG control M or press the cursor
source and press the ENTER button M/ n.
At this time, you need to select the track number of the playing
medium. The display indicates "NUMBER XX".
MULTI JOG
(PUSH ENTER)
select the track number. To increase the number, turn the JOG
control M or press the cursor
decrease, turn to the left. You can select number from 1 to 99.
Please confirm the desired track number of the selected
medium.
played. Next, select whether to record or not.
[SET TO "AUTO"]: This is available only when system control
switch is set to SYSTEM position
select "AUTO" and press the ENTER button M/ n. The display
indicates "AUTO" for 2 seconds. Next, set volume level.
MULTI JOG
@ #
@ #
button n to
MULTI JOG
(PUSH ENTER)
@ #
button n.
MULTI JOG
MULTI JOG
@ #
button n to select
@ #
button n to select the
MULTI JOG
(PUSH ENTER)
@ #
button n to
@ #
button n to the right, and to
@ #
button n to
Hide quick links:
Advertisement
Table of Contents
