Lenovo ThinkPad T430 Hardware Maintenance Manual

Lenovo ThinkPad T430 Hardware Maintenance Manual

Hide thumbs Also See for ThinkPad T430:
Table of Contents

Advertisement

ThinkPad T430 and T430i
Hardware Maintenance Manual

Advertisement

Table of Contents
loading

Summary of Contents for Lenovo ThinkPad T430

  • Page 1 ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 2 Appendix A “Notices” on page 117. Third Edition (March 2013) © Copyright Lenovo 2012, 2013. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.
  • Page 3: Table Of Contents

    Checkout guide ....LCD FRUs and CRUs ..Lenovo Solution Center ..Miscellaneous kits and other FRUs ..
  • Page 4 Trademarks ....1160 LCD unit ....ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 5: About This Manual

    About this manual ® This manual contains service and reference information for the following ThinkPad products. ThinkPad T430 and T430i Machine Type 2342, 2344, 2345, 2347, 2349, 2350, 2351 Use this manual along with the advanced diagnostic tests to troubleshoot problems. Important: This manual is intended only for trained service technicians who are familiar with ThinkPad products.
  • Page 6 ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 7: Chapter 1. Safety Information

    • Reinstall all covers correctly before returning the machine to the customer. • Fan louvers on the machine help to prevent overheating of internal components. Do not obstruct fan louvers or cover them with labels or stickers. © Copyright Lenovo 2012, 2013...
  • Page 8: Electrical Safety

    • Do not service the following parts with the power on: – Power supply units – Pumps – Blowers and fans – Motor generators – Units similar to those listed above This practice ensures correct grounding of the units. ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 9: Safety Inspection Guide

    0.1 ohm or less between the external ground pin and the frame ground. b. The power cord should be the authorized type specified for your computer. Go to: http://www.lenovo.com/serviceparts-lookup. c. Insulation must not be frayed or worn. 4. Check for cracked or bulging batteries.
  • Page 10: Grounding Requirements

    The safety notices in this section are provided in the following languages: • English • Arabic • Brazilian Portuguese • French • German • Hebrew • Japanese • Korean • Spanish • Traditional Chinese DANGER ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 11 DANGER DANGER DANGER DANGER DANGER DANGER Chapter 1 Safety information...
  • Page 12 DANGER ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 13 PERIGO PERIGO PERIGO Chapter 1 Safety information...
  • Page 14 PERIGO PERIGO PERIGO PERIGO PERIGO ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 15 DANGER DANGER DANGER DANGER DANGER Chapter 1 Safety information...
  • Page 16 DANGER DANGER DANGER VORSICHT VORSICHT ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 17 VORSICHT VORSICHT VORSICHT VORSICHT VORSICHT VORSICHT Chapter 1 Safety information...
  • Page 18 ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 19 Chapter 1 Safety information...
  • Page 20 ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 21 Chapter 1 Safety information...
  • Page 22 ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 23: Laser Compliance Statements (Multilingual Translations)

    Laser compliance statements (multilingual translations) The laser compliance statements in this section are provided in the following languages: • English • Arabic • Brazilian Portuguese • French • German • Hebrew • Japanese • Korean • Spanish • Traditional Chinese Chapter 1 Safety information...
  • Page 24 ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 25 Chapter 1 Safety information...
  • Page 26 ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 27 Chapter 1 Safety information...
  • Page 28 ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 29 Chapter 1 Safety information...
  • Page 30 ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 31: Chapter 2. Important Service Information

    UEFI BIOS downloads. Telephone numbers for Lenovo Support are available at http://www.lenovo.com/support/phone • System Disassembly/Reassembly videos that show the FRU removals or replacements for the Lenovo authorized service technicians are available in the following support site: http://www.lenovoservicetraining.com/ion/...
  • Page 32: Strategy For Replacing A Hard Disk Drive

    Dynamic Configure To Order (CTO) This provides the ability for a customer to configure a Lenovo solution from an eSite, and have this configuration sent to fulfillment, where it is built and shipped directly to the customer. The machine label and eSupport will load these products as the 4-digit MT and 3-digit model, where model = “CTO”...
  • Page 33: Fru Identification For Cto, Cmv, And Gav Products

    FRU identification for CTO, CMV, and GAV products Use Lenovo eSupport to identify major FRUs, FRU part numbers, and FRU descriptions for CTO, CMV, and GAV products at an MT - serial number level. Examples of major FRUs are hard disk drive, system board, liquid crystal display (LCD), and memory module.
  • Page 34 ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 35: Chapter 3. General Checkout

    This chapter presents following information: • “What to do first” on page 29 • “Checkout guide” on page 30 – “Lenovo Solution Center” on page 30 – “Quick test programs” on page 30 – “UEFI diagnostic program” on page 31 –...
  • Page 36: Checkout Guide

    The Lenovo Solution Center program is available for download at http://www.lenovo.com/diags. To run the Lenovo Solution Center program, go to Control Panel and click System and Security ➙ Lenovo - System Health and Diagnostics, and then follow the instructions on the screen.
  • Page 37: Uefi Diagnostic Program

    • Microsoft Windows Server 2003 • Microsoft Windows Server 2008 To download and install a quick test program, go to http://www.lenovo.com/diags and follow the instructions on the Web site. To run a test using a quick test program, do the following: 1.
  • Page 38: Power System Checkout

    If you computer fails only when the ac power adapter is used, use the instructions in this topic. • If the power problem occurs only when the docking station or the port replicator is used, replace the docking station or the port replicator. ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 39: Checking Operational Charging

    To check for detailed battery status information, do the following: • For Windows 7: Open the Power Manager program and click the Battery tab. • For Windows 8: Open the Lenovo Support program and click Battery Health, or open the Lenovo Settings program and click Power.
  • Page 40: Checking The Backup Battery

    • If the voltage is correct, replace the system board. • If the voltage is not correct, replace the backup battery. • If the backup battery discharges quickly after replacement, replace the system board. ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 41: Chapter 4. Related Service Information

    Service Web site: When the latest maintenance diskette and the system program service diskette become available, they will be posted on http://www.lenovo.com/support. Restoring the factory contents by using the product Recovery Disc Set When the main storage device is replaced because of a failure, no product recovery program is on the new drive.
  • Page 42: Using The Windows Recovery Programs On The Windows 8 Operating System

    3. Depending on your needs, do one of the following: • To perform a quick format, click Just remove my files to start the process. The process will take several minutes. ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 43 • To perform a complete format, click Fully clean the drive to start the process. The process will take several hours. 4. Follow the instructions on the screen to reset your computer to the factory default settings. Using the advanced startup options With the advanced startup options, you can change the firmware settings of the computer, change the startup settings of the Windows operating system, start the computer from an external device, or restore the Windows operating system from a system image.
  • Page 44: Passwords

    The computer does not start until the password is entered. Note: If only a supervisor password is set, the password prompt will not be displayed when the operating system is started. ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 45: Power-On Password

    If a master hard disk password has been set, it can be used to access the hard disk drive. If no master hard disk password is available, neither Lenovo nor Lenovo authorized service technicians provide any services to reset either the user hard disk password or the master hard disk password, or to recover data from the hard disk drive.
  • Page 46: How To Remove The Hard Disk Password

    To put the system back to operational status, the only Lenovo and Lenovo-authorized service solution would be to replace the hard disk drive or solid-state drive with a scheduled fee.
  • Page 47: Hibernation Mode

    • The microprocessor stops. To enter sleep mode, press Fn+F4. In certain circumstances, the computer goes into sleep mode automatically: • After a period of inactivity specified in power plan settings • When the battery indicator blinks orange, indicating that the battery power is low To cause the computer to return from sleep mode and resume operation, do one of the following: •...
  • Page 48: Symptom-To-Fru Index

    1. Charge the battery pack. Critical low-battery error 2. Battery pack. 0191 1. Run the ThinkPad Setup program, and then save System Security—Invalid Remote Change requested. current setting by pressing F10. 2. System board. ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 49 Table 2. Numeric error codes (continued) FRU or action, in sequence Symptom or error 0199 1. Run the ThinkPad Setup program, and then save System Security— Security password retry count the current setting by pressing F10. exceeded. 2. System board. 0251 1.
  • Page 50: Error Messages

    If the LCD you are servicing has two or less visible defective pixels, it should not be considered faulty. However, if the LCD has three or more visible defective pixels, it will be deemed as defective by Lenovo and it should be replaced.
  • Page 51: Intermittent Problems

    • This policy applies to all ThinkPad notebook computers purchased on 1 January, 2008 or later. • Lenovo will not provide warranty replacement if the LCD is within specifications because we cannot guarantee that any replacement LCD will have zero pixel defects.
  • Page 52 6. If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU. 7. If the problem remains, replace the following FRUs one at a time (do not replace a nondefective FRU): a. System board b. LCD assembly ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 53: Chapter 5. Status Indicators

    Chapter 5. Status indicators This chapter presents the system status indicators that show the status of the computer. © Copyright Lenovo 2012, 2013...
  • Page 54 Quick blinking orange: An error has occurred in the battery. The battery status indicator blinks three times: The ac power adapter is attached to the computer. ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 55 Table 7. Status indicators (continued) Indicator Meaning The battery status indicator is off: The battery pack of the computer is detached or the computer is powered off. Sleep status indicator Green: The computer is in sleep mode. Blinking green: The computer is entering sleep mode or hibernation mode, or is resuming normal operation.
  • Page 56 ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 57: Chapter 6. Fn Key Combinations

    • For Windows 7: Opens the Communications settings window, in which you can preview your video image, take a snapshot of your current image, and change the camera and audio settings. • For Windows 8: Starts the Lenovo Settings program, which enables you to change the camera and audio settings. Fn+F7 Switches between the computer display and an external monitor.
  • Page 58 ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 59: Chapter 7. Locations

    47) Power button Touch pad Built-in speakers TrackPoint buttons Security keyhole TrackPoint pointing stick ® UltraNav poiting device USB 2.0 connector Wireless radio switch Volume control buttons ExpressCard slot Black button Media card reader slot © Copyright Lenovo 2012, 2013...
  • Page 60: Rear View

    Locating FRUs and CRUs This topic introduces the following service parts: • “Major FRUs and CRUs” on page 56 • “LCD FRUs and CRUs” on page 58 • “Miscellaneous kits and other FRUs” on page 59 ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 61 CRUs, you can either install the CRU yourself or you can request that a Service Provider install the CRU according to the warranty service for your product. If you intend on installing the CRU, Lenovo will ship the CRU to you. CRU information and replacement instructions are shipped with your product and are available from Lenovo at any time upon request.
  • Page 62: Major Frus And Crus

    Table 9. Major FRUs and CRUs FRU description Self-service Optional-service LCD unit (see “LCD FRUs and CRUs” on page 58) Keyboard bezel assembly Express dummy card PCI Express Mini Card for wireless LAN/WiMAX Memory module ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 63 Table 9. Major FRUs and CRUs (continued) FRU description Self-service Optional-service Speaker assembly Magnesium structure frame Serial Ultrabay Enhanced bay or blank bezel Smart card reader (on some modes) Smart card reader FPC cable I/O sub card DC-in connector Battery pack Base cover assembly Backup battery Memory module slot cover...
  • Page 64: Lcd Frus And Crus

    LCD FRUs and CRUs Table 10. LCD FRUs and CRUs FRU description Self-service Optional-service LCD bezel assembly Integrated camera LCD panel Hinges Wireless antenna set ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 65: Miscellaneous Kits And Other Frus

    Table 11. Miscellaneous kits FRU descriptions Self-service Optional service CRU LCD miscellaneous kit: • Logo ThinkPad • Logo Lenovo • Icon Plate Rear • LCD Latch R • LCD Latch L • AL SHEET • POLON 1 • POLON 2 (2) •...
  • Page 66 Screw and tape kit: • Screw M2.0 x L3.0 (40) • Screw M2.0 x L9.5 (10) • Screw M2.0 x L14.0 (10) • Screw M2.5 x L4.0 (8) • Screw M2.5 x L6.5 (8) ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 67: Looking Up Fru Information

    • Tape cable fix 10 x 30 (2) • English Spec Table 12. Other FRUs FRU descriptions Self-service Optional service CRU ac adapter Power cord Looking up FRU information For detailed FRU information, including part numbers, descriptions, and substitution part numbers, go to http://www.lenovo.com/serviceparts-lookup. Chapter 7 Locations...
  • Page 68 ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 69: Chapter 8. Fru Replacement Notices

    Lenovo will ship the CRU to you. CRU information and replacement instructions are shipped with your product and are available from Lenovo at any time upon request. You can find a list of CRUs for your product in this Hardware Maintenance Manual. An electronic version of this manual can be found at http://www.lenovo.com/support.
  • Page 70: Retaining Serial Numbers

    If you replace the system board, you must restore the serial number of the system unit to its original value. Before replacing the system board, save the original serial number by doing the following: 1. Install the latest version of LENOVO ThinkPad Hardware Maintenance Diskette or Maintenance Key, and then restart the computer.
  • Page 71: Retaining The Uuid

    When you replace the system board, follow the following steps to create new UUID for the system board if the system board does not have a UUID: 1. Install the latest version of LENOVO ThinkPad Hardware Maintenance Diskette or Maintenance Key, and then restart the computer.
  • Page 72 If the system board is being replaced, try to read the ECA information from the old system board and transfer the information to the new system. If the system board is inoperable, this will not be possible. ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 73: Chapter 9. Removing Or Replacing A Fru

    Lenovo will ship the CRU to you. CRU information and replacement instructions are shipped with your product and are available from Lenovo at any time upon request. You can find a list of CRUs for your product in this Hardware Maintenance Manual. An electronic version of this manual can be found at http://www.lenovo.com/support.
  • Page 74: Before Servicing The Computer

    The only exception to this is if the battery pack is physically damaged or a customer is reporting a possible safety issue. • If the Lenovo Solution Center program is not installed in the computer, the customer should download this program before a non-physically damaged battery pack is replaced. Note that the replacement of a physically damaged battery pack is not covered by the warranty.
  • Page 75: 1020 Expresscard Blank Bezel

    Removal steps of battery pack DANGER Use only the authorized battery specified for your computer. Any other battery could ignite or explode. Unlock the battery latch . Hold the battery latch in the unlocked position, and remove the battery pack in the direction shown by the arrow When installing: Install the battery pack in the slot.
  • Page 76: 1030 Serial Ultrabay Enhanced Bay Or Blank Bezel

    , and slide the bay eject latch in the direction shown by the arrow . Then pull out the Serial Ultrabay Enhanced bay or the blank bezel in the direction shown by the arrow ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 77: 1040 Hard Disk Drive Or Solid-State Drive

    1040 Hard disk drive or solid-state drive For access, remove this FRU: • “1010 Battery pack” on page 68 Attention: • Do not drop the drive or apply any physical shock to it. The drive is sensitive to physical shock. Improper handling can cause damage and permanent loss of data.
  • Page 78 Removal steps of hard disk drive or solid-state drive Note: Loosen the screw Step Screw (quantity) Color Torque Capture screw (1) Black 0.181 Nm (1.85 kgf-cm) ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 79: 1050 Memory Module Slot Cover

    For hard disk drive and rubber rails: For solid-state drive and spacers: When installing: Ensure that the solid-state drive spacers or the hard disk drive rubber rails are attached firmly. 1050 Memory module slot cover For access, remove this FRU: •...
  • Page 80: 1060 Backup Battery

    (1.85 kgf-cm) 1060 Backup battery For access, remove these FRUs in order: • “1010 Battery pack” on page 68 • “1050 Memory module slot cover” on page 73 Removal steps of backup battery ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 81: 1070 Memory Module (In The Slot On The Underside Of The Computer)

    DANGER Use only the authorized battery specified for your computer. Any other battery could ignite or explode. 1070 Memory module (in the slot on the underside of the computer) For access, remove these FRUs in order: • “1010 Battery pack” on page 68 •...
  • Page 82 Black 0.181 Nm M2 × 3 mm, wafer-head, nylon-coated (1) (1.85 kgf-cm) When installing: Plug the red cable into the main connector, and the blue cable into the auxiliary connector on the card. ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 83 If the computer you are servicing is a wireless WAN-ready model and does not have a wireless WAN card, route the antenna cables and secure them with tape as shown in the following illustration. Removal steps of PCI Express Half Mini Card for wireless WAN Unplug the connectors by using the antenna RF connector removal tool, or pick the connectors with your fingers and gently unplug them in the direction shown by the arrows Step...
  • Page 84 The computer comes with either a PCI Express Mini Card for wireless WAN or an mSATA solid-state drive. If the computer is equipped with an mSATA solid-state drive, it is installed in the wireless WAN card slot. ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 85 • Ensure that you partition the mSATA solid-state drive after installing it on the computer you are servicing. Otherwise, the mSATA solid-state drive will not function correctly. For instructions on on how to partition an mSATA solid-state drive, go to http://www.lenovo.com/support/msata-fru. Torque...
  • Page 86: 1090 Keyboard

    “1010 Battery pack” on page 68 • “1050 Memory module slot cover” on page 73 Removal steps of keyboard Step Screw (quantity) Color Torque 0.181 Nm M2 × 14 mm, wafer-head, nylon-coated (2) Silver (1.85 kgf-cm) ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 87 Press the keyboard in the direction shown by the arrows until the rear edge of the keyboard is detached from the keyboard bezel. Lift the keyboard a little in the direction shown by the arrow , and then detach the connector Chapter 9 Removing or replacing a FRU...
  • Page 88 Installation steps of keyboard Attach the keyboard connector. Attach the keyboard and ensure that the keyboard edge is under the frame. ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 89: 1100 Memory Module (In The Slot Under The Keyboard)

    When the front edge of the keyboard is housed firmly, gently press the keys with your palms and slightly slide the keyboard toward you until the keyboard is in place. Secure the keyboard by tightening the screws from the bottom side of the computer. 1100 Memory module (in the slot under the keyboard) For access, remove these FRUs in order: •...
  • Page 90 When installing: Insert the notched end of the memory module into the slot. Press the memory module firmly, and pivot it until it snaps into place. Ensure that it is firmly installed in the slot and does not move easily. ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 91: 1120 Pci Express Mini Card For Wireless Lan/Wimax

    1120 PCI Express Mini Card for wireless LAN/WiMAX For access, remove these FRUs in order: • “1010 Battery pack” on page 68 • “1050 Memory module slot cover” on page 73 • “1090 Keyboard” on page 80 PCI Express Mini Card for wireless LAN/WiMAX Unplug the connectors by using the antenna RF connector removal tool, or pick the connectors with your fingers and gently unplug them in the direction shown by the arrows Note: Some models might have only two antenna cables.
  • Page 92: 1130 Keyboard Bezel Assembly, Fpc Cable, And Bluethooth Daughter Card

    “1020 ExpressCard blank bezel” on page 69 • “1050 Memory module slot cover” on page 73 • “1090 Keyboard” on page 80 Removal steps of keyboard bezel assembly, FPC cable, and Bluetooth daughter card ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 93 Step Screw (quantity) Color Torque Black 0.181 Nm M2 × 14 mm, wafer-head, nylon-coated (5) (1.85 kgf-cm) M2 × 3 mm, wafer-head, nylon-coated (1) Black 0.181 Nm (1.85 kgf-cm) Torque Step Screw (quantity) Color M2 × 3 mm, wafer-head, nylon-coated (2) Black 0.181 Nm (1.85 kgf-cm)
  • Page 94 Bluetooth daughter card also is attached on the underside of the keyboard bezel assembly. For the models that do not have a Bluetooth daughter card, skip steps When installing: Ensure that the connectors are attached firmly. ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 95: 1140 Smart Card Reader

    Step Screw (quantity) Color Torque Black 0.181 Nm M2 × 3 mm, wafer-head, nylon-coated (1) (1.85 kgf-cm) When installing: Ensure that the connector is attached firmly. 1140 Smart card reader For access, remove these FRUs in order: • “1010 Battery pack” on page 68 •...
  • Page 96 Removal steps of smart card reader or smart card dummy spacer Some models have a smart card dummy spacer as a miscellaneous part. For those models, remove the spacer as shown: ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 97: 1150 Speaker Assembly

    Torque Step Screw (quantity) Color M2 × 3 mm, wafer-head, nylon-coated (2) Black 0.181 Nm (1.85 kgf-cm) When installing: Ensure that the connector is attached firmly. 1150 Speaker assembly For access, remove these FRUs in order: • “1010 Battery pack” on page 68 •...
  • Page 98 M2 × 3 mm, wafer-head, nylon-coated (2) (1.85 kgf-cm) When installing: Attach the speaker assembly and route the cable as shown in the following illustration, and ensure that the speaker connector is attached firmly. ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 99: 1160 Lcd Unit

    1160 LCD unit For access, remove these FRUs in order: • “1010 Battery pack” on page 68 • “1020 ExpressCard blank bezel” on page 69 • “1050 Memory module slot cover” on page 73 • “1080 PCI Express Mini Card for wireless WAN or mSATA solid-state drive” on page 75 •...
  • Page 100 Screw (quantity) Color Torque Black 0.181 Nm M2 × 3 mm, wafer-head, nylon-coated (1) (1.85 kgf-cm) Torque Step Screw (quantity) Color M2.5 × 6.5 mm, wafer-head, nylon-coated (2) Black 0.392 Nm (4.0 kgf-cm) ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 101 When installing: • Ensure that you attach the connectors firmly. • Ensure that you route the cables correctly and tape up in the proper positions as shown in the above illustration. • When you route the cables, ensure that they are not subject to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken.
  • Page 102: 1170 Thermal Fan Assembly

    • “1120 PCI Express Mini Card for wireless LAN/WiMAX” on page 85 • “1130 Keyboard bezel assembly, FPC cable, and Bluethooth daughter card” on page 86 • “1150 Speaker assembly” on page 91 ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 103 Removal steps of thermal fan assembly Note: Loosen the screws in ascending alphabetic order as illustrated. For models that have a discrete graphics card: : Step Screw (quantity) Color Torque 0.181 Nm Capture shoulder screw (4) Silver (1.85 kgf-cm) M2 × 3 mm, wafer-head, nylon-coated (1) black 0.181 Nm (1.85 kgf-cm)
  • Page 104 For models that have an integrated graphics card: : Torque Step Screw (quantity) Color Capture shoulder screw (4) Silver 0.181 Nm (1.85 kgf-cm) ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 105 When installing: Before you attach the thermal fan assembly to the computer, apply thermal grease, at an amount of 0.2 grams, on the parts marked as in the following illustrations. Either too much or too less application of grease can cause a thermal fan problem due to imperfect contact with a component. For the fan in models that have an integrated graphics module, you need to peel the thin film off from the thermal rubber marked For models that have a discrete graphics card: Chapter 9...
  • Page 106: 1180 Microprocessor

    • “1130 Keyboard bezel assembly, FPC cable, and Bluethooth daughter card” on page 86 • “1150 Speaker assembly” on page 91 • “1160 LCD unit” on page 93 • “1170 Thermal Fan assembly” on page 96 ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 107: 1190 Base Cover Assembly And Dc-In Connector

    Attention: The microprocessor is extremely sensitive. When you service the microprocessor, avoid any kind of rough handling. Removal steps of microprocessor Rotate the head of the screw in the direction shown by the arrow to release the lock, and remove the microprocessor .
  • Page 108 M2 × 3 mm, wafer-head, nylon-coated (6) (1.85 kgf-cm) M2 × 9.5 mm, wafer-head, nylon-coated (1) Black 0.181 Nm (1.85 kgf-cm) When installing: Ensure that the wireless switch is adjusted as shown in callout ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 109 Torque Step Screw (quantity) Color M2 × 3 mm, wafer-head, nylon-coated (1) Black 0.181 Nm (1.85 kgf-cm) When installing: Ensure that the connector is attached firmly. Applying labels to the base cover The new base cover FRU is shipped with a kit containing labels of several kinds. Apply those labels when you replace the base cover.
  • Page 110: 1200 Magnesium Structure Frame

    • “1130 Keyboard bezel assembly, FPC cable, and Bluethooth daughter card” on page 86 • “1150 Speaker assembly” on page 91 • “1160 LCD unit” on page 93 • “1170 Thermal Fan assembly” on page 96 • “1180 Microprocessor” on page 100 ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 111: 1210 System Board Assembly, Expresscard Slot, And I/O Sub Card

    • “1190 Base cover assembly and DC-in connector” on page 101 Removal steps of magnesium structure frame Step Screw (quantity) Color Torque M2 × 3 mm, wafer-head, nylon-coated (4) Black 0.181 Nm (1.85 kgf-cm) M2 × 9.5 mm, wafer-head, nylon-coated (2) Black 0.181 Nm (1.85 kgf-cm)
  • Page 112 Note: The GPU is only for models that have a discrete graphics card. Models that have an integrated graphics module do not have a GPU on the system board. Accelerometer chip for the hard disk drive Active Protection System™ ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 113 Torque Step Screw (quantity) Color M2 × 3 mm, wafer-head, nylon-coated (2) Black 0.181 Nm (1.85 kgf-cm) Torque Step Screw (quantity) Color M2 × 3 mm, wafer-head, nylon-coated (1) Black 0.181 Nm (1.85 kgf-cm) Chapter 9 Removing or replacing a FRU...
  • Page 114: 2010 Lcd Bezel Assembly

    When installing: Ensure that all the latches are attached firmly. Then secure the bezel with the screws. 2020 LED board For access, remove these FRUs in order: • “1010 Battery pack” on page 68 • “2010 LCD bezel assembly” on page 108 ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 115: 2030 Integrated Camera

    Removal steps of LED board Torque Step Screw (quantity) Color M2 × 3 mm, flat-head, nylon-coated (1) Black 0.181 Nm (1.85 kgf-cm) When installing: Ensure that the connector is attached firmly. 2030 Integrated camera For access, remove these FRUs in order: •...
  • Page 116 Removal steps of integrated camera Step Screw (quantity) Color Torque Black 0.181 Nm M2 × 3 mm, flat-head, nylon-coated (1) (1.85 kgf-cm) ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 117: 2040 Lcd Panel And Lcd Cable

    2040 LCD panel and LCD cable For access, remove these FRUs in order: • “1010 Battery pack” on page 68 • “1020 ExpressCard blank bezel” on page 69 • “1050 Memory module slot cover” on page 73 • “1080 PCI Express Mini Card for wireless WAN or mSATA solid-state drive” on page 75 •...
  • Page 118: 2050 Led And Camera Cable

    “1160 LCD unit” on page 93 • “2010 LCD bezel assembly” on page 108 • “2020 LED board” on page 108 • “2030 Integrated camera” on page 109 • “2040 LCD panel and LCD cable” on page 111 ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 119: 2060 Wireless Antenna Set

    Removal steps of LED and camera cable 2060 Wireless antenna set For access, remove these FRUs in order: • “1010 Battery pack” on page 68 • “1020 ExpressCard blank bezel” on page 69 • “1050 Memory module slot cover” on page 73 •...
  • Page 120 As you route the cables, ensure that they are not subject to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken. Torque Step Screw (quantity) Color M2 × 3 mm, flat-head, nylon-coated (2) Black 0.181 Nm (1.85 kgf-cm) ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 121: 2070 Hinges And Lcd Rear Cover Assembly

    2070 Hinges and LCD rear cover assembly For access, remove these FRUs in order: • “1010 Battery pack” on page 68 • “1020 ExpressCard blank bezel” on page 69 • “1050 Memory module slot cover” on page 73 • “1080 PCI Express Mini Card for wireless WAN or mSATA solid-state drive” on page 75 •...
  • Page 122 Step Screw (quantity) Color Torque Black 0.392 Nm M2.5 × 4 mm, wafer-head, nylon-coated (4) (4.0 kgf-cm) When installing: Attach the hinges as shown in the following illustration. ThinkPad T430 and T430i Hardware Maintenance Manual...
  • Page 123: Appendix A. Notices

    Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any Lenovo intellectual property right may be used instead.
  • Page 124: Electronic Emissions Notices

    Electronic emissions notices For electronic emission information on Class B digital devices, refer to the corresponding information in the User Guide. Trademarks The following terms are trademarks of Lenovo in the United States, other countries or both: Active Protection System Lenovo ThinkLight...
  • Page 126 Part Number: 0B48304_02 Printed in China (1P) P/N: 0B48304_02 *1P0B48304_02*...

This manual is also suitable for:

Thinkpad t430i

Table of Contents