TK-7360/ TK-8360 VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER INSTRUCTION MANUAL ÉMETTEUR-RÉCEPTEUR FM VHF/ ÉMETTEUR-RÉCEPTEUR FM UHF MODE D’EMPLOI TRANSCEPTOR FM VHF/ TRANSCEPTOR FM UHF MANUAL DE INSTRUCCIONES RICETRASMETTITORE FM VHF/ RICETRASMETTITORE FM UHF MANUALE DI ISTRUZIONI VHF-FM-TRANSCEIVER/ UHF-FM-TRANSCEIVER BEDIENUNGSANLEITUNG VHF FM ZENDONTVANGER/ UHF FM ZENDONTVANGER GEBRUIKSAANWIJZING VHF FM EL TELSİZİ/ UHF FM EL TELSİZİ...
Page 2
VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER TK-7360/ TK-8360 INSTRUCTION MANUAL Firmware Copyrights The title to and ownership of copyrights for firmware embedded in Kenwood product memories are reserved for Kenwood Corporation. NOTIFICATION This equipment complies with the essential requirements of Directive 1999/5/EC.
Page 3
Information on Disposal of Old Electrical and Electronic Equipment and Batteries (applicable for EU countries that have adopted separate waste collection systems) Products and batteries with the symbol (crossed-out wheeled bin) cannot be disposed as household waste. Old electrical and electronic equipment and batteries should be recycled at a facility capable of handling these items and their waste byproducts.
Page 4
We are grateful you have chosen Kenwood for your personal moble applcatons. Ths nstructon manual covers only the basc operatons of your moble rado. Ask your dealer for nformaton on any customzed features they may have added to your rado.
◆ The transcever operates n 12 v negatve ground systems only! Check the battery polarty and voltage of the vehcle before nstallng the transcever. ◆ Use only the suppled DC power cable or a Kenwood optonal DC power cable. ◆ Do not cut and/or remove the fuse holder on the DC power cable.
GETTING STARTED Note: The following instructions are for use by your Kenwood dealer, an authorized Kenwood service facility, or the factory. upplied cceSSorieS Carefully unpack the transceiver. We recommend that you identify the items listed below before discarding the packing material. If any items are missing or have been damaged during shipment, file a claim with the carrier immediately.
n Installing the Transceiver For passenger safety, install the transceiver securely using the supplied mounting bracket and screw set, so the transceiver will not break loose in the event of a collision. Note: Before installing the transceiver, check how far the mounting screws will extend below the surface.
GETTING ACQUAINTED ront And iewS ① (Power) switch Press to switch the transceiver ON or OFF. ② keys Press to activate their programmable functions {page 5}. ③ keys Press to activate their programmable functions {page 5}. ④ TX/RX Indicator Lights red while transmitting and green while receiving a signal. Flashes orange when receiving an optional signaling call.
Page 9
iSplAy Icon Description Displays the signal strength. Not used. Lights when the GPS position is determined. Signaling is turned off. A DTMF call is being received. The Talk Around function is on. Lights while scanning or while paused on a channel. Blinks when scan is temporarily stopped.
PROGRAMMABLE FUNCTIONS The , , , S, A, <B, C>, and n keys can be programmed with the functions listed below. Ask your dealer for details on these functions. • None • OST List • Auto Reply Message • Paging Call •...
BASIC OPERATIONS on/ oFF witching ower Press to switch the transceiver ON. • A beep sounds and the display illuminates. If the Power-on tone select is set to OFF, the beep will not sound. • If the Transceiver Password function is programmed, “PASSWORD” will appear on the display.
rAnSmitting eceiVing 1 Select your desired zone and channel. 2 Press the microphone PTT switch and speak into the microphone to transmit. Release the PTT switch to receive. • For best sound quality at the receiving station, hold the microphone approximately .5 inches (3 ~ 4 cm) from your mouth.
elete You can add and remove zones and/or channels/group IDs to and from your scan list. 1 Select your desired zone and/or channel/group ID. 2 Press the key programmed as Scan Delete/Add to remove a channel or press and hold the key for approximately second to remove a zone. •...
Page 14
n Storing an Autodial Entry 1 Press the key programmed as Autodial Programming. 2 Press (if the key assignment list selection is configured as “Enabled”) or <B/C> to select a memory location number. 3 Press S to enter a name for the list number. 4 Press to select a digit.
SIGNALING (Qt)/ d (dQt) uiet igitAl uiet Your dealer may have programmed QT or DQT signaling on your transceiver channels. A QT tone/ DQT code is a sub-audible tone/code which allows you to ignore (not hear) calls from other parties who are using the same channel. ptionAl ignAling Your dealer may also program several types of optional signaling for your...
FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTION FleetSync is an Alphanumeric 2-way Paging Function and is a protocol owned by Kenwood Corporation. Note: If set up by your dealer, your transceiver may use the MDC-200 feature in place of FleetSync. MDC-200 and FleetSync cannot be operated simultaneously.
n Transmitting 1 Select your desired zone and channel. 2 Press the key programmed as Selcall or Selcall + Status. 3 Press (if the key assignment list selection is configured as “Enabled”) or <B/C> to select the ID of the station you want to call. •...
4 Press S to enter Status mode. 5 Press (if the key assignment list selection is configured as “Enabled”) or <B/C> to select the status ID you want to transmit. • You can also enter the status ID directly by using the keypad. 6 Press the PTT switch or n to initiate the status call.
Page 19
Your dealer can activate the built-in scrambler function, or they can add a more secure optional scrambler board to your transceiver. Ask your dealer for details. u This function cannot be used in certain countries. Contact your Kenwood dealer for further information.
2 Press (if the key assignment list selection is configured as “Enabled”) or <B/C> to select your desired scrambler code. 3 Press S, , or to store the new setting. • After changing your scrambler code, be sure to inform all of your group members of the new code so they can also reset their transceivers.
(pA) ublic ddreSS The PA system can only be used with an external speaker. 1 Press the key programmed as Public Address to activate the Public Address function. • The icon appears on the display. 2 Press and hold the PTT switch, then speak into the microphone to make your address through the external speaker.
• “BUSY” appears on the display when you press the PTT switch. Use a different channel or wait until the channel becomes free. If your dealer has programmed BCL Override for your transceiver, you can override the BCL by pressing the PTT switch again, immediately after releasing it, when the channel is busy.
Page 23
3 Press the S, n, or key to end the recording at any time and store it into the transceiver memory. • If the memory becomes full, recording will stop automatically and store the voice memo to memory. n Auto Reply Message You can set the transceiver to automatically respond to Individual Calls.