The features section starting on page 26 of this manual will describe these settings. Most settings have been preset for optimal performance. If you need any assistance with installation or setup of your new Hunter Thermostat, please call us, our technical support staff is ready to help! USA: 1-888-830-1326...
Page 4
Know Your Thermostat Your Hunter programable thermostat: 1. Enters Schedule Setup for altering scheduled programs. 2. Sets the Save Away feature for when you will not be home during a regularly programmed time. 3. Confirms completion of an action or returns you to the Home screen.
Page 6
Know Your Thermostat 1. Holds 2 “AA” Batteries. 2. HE/HG Switch - allows you to set your furnace to Gas/Oil or Electric, based on the type of system you have. 3. Allows your thermostat to operate your HVAC system* properly by indicating the system type that you have.
Page 8
Know Your Thermostat 1. Shows the current day of the week or weekend. 2. Indicates the thermostat is running in schedule mode. 3. Indicates the current room temperature. 4. C will display when in Celsius mode. Nothing will display when set to Fahrenheit.
Setting Day and Time Once you install the batteries, the thermostat will prompt you to set the current day and time. 1. You will notice that “Mon” will be flashing at the top left of your screen. Use the buttons to move to your current day of the week and press the button to advance to the next step.
Scheduling Introduction Read the scheduling section thoroughly to ensure you understand your scheduling options and which will best fit with your lifestyle. The following notes should help you with scheduling: • The schedule time can be set in 15 minute increments, and remains the same for both Heat and Cool programs.
Setting Your Schedule 1. Press the Button to enter Scheduling mode. Schedule buttons to select “On” and then to move forward 2. Use the Next to Scheduling. Note: If you do not wish to use the scheduling option on your thermostat, refer to page 20, step 2.
Page 16
Setting Your Schedule 5. Use the buttons to adjust the start time on the left of the screen for the period and press . Again you will use the buttons to Next adjust the end time on the right of the screen for this scheduled period. Press again.
Temporary Temperature Change With Temporary Temperature Change you have the ability to alter the temperature for only the current running schedule for one day. 1. Press the button once to activate the screen, the backlight will come on. 2. Use the buttons again to select a new temperature.
Turning Off Scheduling To turn off your schedule and have the thermostat permanently set to one temperature: 1. Press the button once. Schedule 2. Use the button to switch to Off and select Done/ Home 3. The screen will show “Updated!” and return you to the home screen. Note: You will notice the black bar on the screen beside the Schedule button is not displayed anymore.
Save Away The Save Away feature allows you to set a lower or higher temperature for time you will be away from your home outside of your normal Away schedule. This can include days you will be away for vacation, or a few hours away from your home.
Alerts This chapter will outline the various alerts the thermostat will report to you and how to respond to them. 1. Low Battery: This icon will appear when your batteries are starting to run low on power and should be changed to avoid system interruptions, (Figure 1) Change the batteries by gripping the sides of the thermostat firmly and pulling straight back.
Menu Options Under your Menu options you have the ability to reset your filter counter, change your day/time settings, and change first and second stage spans. To change each setting, you will need to hit the button to move through Next each feature.
Page 28
Menu Options 4. The next Menu option is to set your thermostat’s primary span. Use the buttons to adjust between 1, 2, or, 3 degrees. Press after Next this has been changed or if no changes are necessary. The span setting regulates when and how long your system will run.
Additional Features Armchair Programming There is no need to stand at the wall where the thermostat is mounted while programming or changing settings. Simply remove the thermostat from the wall and make the necessary changes in the comfort of a chair. You can also set your programming and settings before you even install the thermostat.
Page 32
Troubleshooting and Support Problem: Fan runs continuously. Solution: 1. Check fan setting to see if it is set to on. 2. Move HG/HE switch to opposite position. Problem: Heating or cooling does not turn on or off. Solution: 1. Check the system is in the right mode (heat or cool). 2.
Technical Support If you need any assistance with installation or setup of your new Hunter thermostat, please call us. Our technical support staff is ready to help! USA: 1-888-830-1326 Canada: 1-866-268-1936 Hours of operation are from 7:00 am to 7:00 pm Monday - Friday and 8:00 am to 5:00 pm on Saturday, Central Time.
PARTICULAR PURPOSE, IN RESPECT TO YOUR HUNTER THERMOSTAT IS LIMITED TO THE PERIOD OF THE EXPRESS WARRANTY SET FORTH ABOVE. This warranty is voided if your Hunter Thermostat is not purchased and used in the USA. This warranty excludes and does not cover defects, malfunctions or...
Page 35
This warranty neither applies to batteries nor to deterioration of, nor damage to the product caused by the use of faulty batteries. Return your product, along with proof of purchase to Hunter Fan Company Service Department, 7130 Goodlett Farms Pkwy., Suite 400, Memphis, TN 38016. You will be responsible for all insurance and freight or other transportation charges to our factory.