Advertisement
Your safety and the safety of
others is very important.
We have provided many important
safety messagesin this manual and
on your appliance. Always read and
obey atl safety messages.
This is the safety alert symbol.
This symbol alerts you to
potential hazardsthat can kill
or hurt you and others. Ali safety
messages wiii foliow the safety alert
symbol and either the word "DANGER"
or "WARNING". These words mean:
You Ganbe killed or seri0usly injured
if you don't follow instructions.
AIi safety messages wili teli you what
the potentiai hazard is, teii you how to
reduce the chance of injury, and tell
you what can happen if the
instructions are not followed.
important:
Observe
all governing
codes and ordinances.
Proper installation
is your
responsibility.
Make sure you have
everything
necessary for correct
installation,
It is the responsibility
of
the installer
to comply
with the
clearances
specified.
Check the location where the range
hood will be instalbd.The
location
should
be away from strong draft
areas, such as windows,
doors, and
strong heating vents.
Mobile home installation
The installation
of this range hood
must conform
to the Manufactured
Home Construction
Safety
Standards, Titb 24 CFR, Part 328
(formerly
the Federal Standard
for
Mobile
Home Construction
and
Safety, Title 24, HUD, Part 280 or
when such standard
is not
applicable,
the Standard
for
Manufactured
Home Installation
1982 (Manufactured
Home Sites,
Communities
and Setups) ANSi
A225.1/NFPA 501A*, or latest edition,
or with local codes.
WARNING -- TO REDUCE THE
RiSK OF FIRE, ELECTRIC
SHOCK, OR iNJURY TO
PERSONS, OBSERVE THE
FOLLOWING:
Installation work and electrical
wiring
must be done by qualified
person(s) in accordance with all
applicable
Codes and Standards,
including
Fire Rated Construction.
Sufficient
air is needed for proper
combustion
and exhausting
of
gases through
the flue (chimney)
of fuel burning equipment
to
prevent back drafting.
Follow the
heating equipment
manufacturer's
guideline and
safety standards such as those
published
by the National Fire
Protection Association
(NFPA),
and the American
Society of
Heating Refrigeration
and Air
Conditioning
Engineers
(ASHRAE), and the local code
authorities.
When cutting or drilling into wall or
ceiling, do not damage electrical
wiring and other hidden utilities.
Ducted fans must always be
vented to the outdoors.
WARNING -- To reduce the risk
of fire, use only metal ductwork.
This unit must be grounded.
This hood is factory set for vented
installations. For non=vented
installations,
purchase Charcoal
Filter Pad Kit No. 4396390 (contains
two filter pads) from your dealer.
Tools and
materials needed
for installation:
* fiat hmade
_ I=I/4"
(3,0 am}
screwdriver
drill hit
pmiers
• I/8"
lot 3 ram} drill
* ddH
hit for pilot homes
* ruiner
• pencil
For vented instaflations,
you also need:
® compass
or
8"
12&3 era} circme
tempBate
metaR snips
* keyhob
saw
® saber
saw
* duet tape
3=I/4"x10" (81.3 x 25A am)
to 5" (152 am} round
transition
piece if using
round vent
6" (15.2 era) round damper
if using 5" (15,2 cml round
vent system
Cabinets with recessed bottoms:
* 2, 2" (5.8 era) wide filler strips. Length and
thickness
determined
by recess dimensions.
* 4 fiat head wood screws or machine screws
with washers and nuts to attach filler strips.
Parts supplied:
* 2, amuminum fimters
3-I/4" x 10"(8.3x 25A era}
damper/vent
connector
* parts bag
important: Observe all governing
codes and ordinances.
it is the customer's
responsibility:
• To contact a qualified electrical
installer.
To assure that the electrical
installation is adequate and in
conformance
with National
Electrical Code, ANSI/NFPA 70
-- latest edition*,
or CSA
Standards C22,1=94, Canadian
Electrical Code, Part 1 and
C22.2 No.0-M91 - latest
edition**
and all local codes
and ordinances.
A separate ground wire must be
used. it is recommended
that a
qualified electrician determine that
the ground path is adequate.
A 120-volt, 60-Hz, AO-only, fused
electrical system is required. A
separate 15=amp circuit is
recommended.
Do not ground to a gas pipe.
Check with a qualified electrician if
you are not sure range hood is
properly grounded.
Do not have a fuse in the neutral or
ground circuit.
IMPORTANT:
Save installation instructions for
electrical inspector's use.
The range hood must be connected
with copper wire only.
The range hood should be
connected directly to the fused
disconnect (or circuit breaker) box
through flexible armored or
nonmetallic
sheathed copper cable.
A U.L.° or C.S.A.-listed strain relief
must be provided at each end of the
power supply cable. Wire sizes
(COPPER WIRE ONLY) and
connections
must conform with the
rating of the appliance as specified
on the model/serial
rating plate.
Advertisement
