Electronic Oven Controls; Oven Light; Troubleshooting - Whirlpool WFE540H0AW0 User Instructions

The oven light is a standard 40-watt appliance bulb. Before
replacing, make sure the oven and cooktop are cool and the
control knobs are in the off position.
2. Turn the glass bulb cover in the back of the oven
counterclockwise to remove.
3. Turn bulb counterclockwise to remove from socket.
To Replace: 4. Replace bulb, then bulb cover by turning clockwise.
1. Unplug range or disconnect power. 5. Plug in range or reconnect power.
TROUBLESHOOTING
First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)
to possibly avoid the cost of a service call.
www.whirlpool.com
Operation
PROBLEM POSSIBLE CAUSES SOLUTIONS
Nothing will operate Power supply cord is unplugged. Plug into a grounded outlet.
ENERGY SAVE is active, and the Press any key on the control to display the Time of Day. See the
display is blank. "Electronic Oven Controls" section for more information.
Cooktop will not operate
Household fuse is blown, or a
circuit breaker is tripped.
The control displays an F9 or F9
E0 error code.
The control knob is not set
correctly.
On ceramic glass models, the
oven control lockout is set.
Replace the fuse or reset the circuit breaker. If the problem
continues, call an electrician.
The electrical outlet in the home may be miswired. Contact a
qualified electrician to verify the electrical supply.
Push in knob before turning to a setting.
See the control lock keypad feature in the "Feature Guide."
Excessive heat around Cookware is not the proper size. Use cookware about the same size as the surface cooking area,
cookware on cooktop element or surface burner. Cookware should not extend more
than 1/2'(1.3 cm) outside the cooking area.
Cooktop cooking results not Control knob set to incorrect heat See "Cooktop Use" section.
what expected level
Cooktop element cycles on and
off on High setting.
Oven will not operate
Range is not level.
Element cycling due to a
temperature limiter
Delay start is set.
Control lock is on.
Level the range. See the Installation Instructions.
This is normal operation. The element may cycle on and off to
keep the cooktop from overheating.
See "Cook Time" section.
Press and hold START for 3 seconds to unlock.
Control is in Demo Mode. Press and hold START TIME for 10 seconds to exit Demo Mode.
Demo Mode is used for display models in a showroom.
Electronic oven control set See "Electronic Oven Controls" section.
incorrectly
Oven temperature too high or Oven temperature needs See "Oven Temperature Control" in the "Electronic Oven
too low adjustment. Controls" section.
Oven indicator lights flash Power to range is turned on or See "Control Display" in the "Electronic Oven Controls" section.
restored. If the indicator lights keep flashing, call for service. See cover
for contact information.
Display shows messages Power failure (display shows Clear the display. On some models, reset the clock, if needed.
flashing time) See "Clock" keypad feature in the "Feature Guide" section.
Error code (display shows letter
followed by number)
Depending on your model, press CANCEL to clear the display.
See "Control Display" in the "Electronic Oven Controls" section.
If it reappears, call for service. See cover for contact
information.
Clean cycle did not work on all
spills
Start needs to be pressed so a
cycle can begin (display shows
"PUSH" or "PSH").
Several cooking cycles between
Clean cycles or spills on oven
walls and doors.
See the "Start" keypad feature in the "Feature Guide" section.
Run additional Clean cycles. Use the AquaLift
TM
Technology
Cleaning Kit. affresh
TM
Kitchen and Appliance Cleaner or
affresh
TM
Cooktop Cleaner can be used for stubborn soils. See
the "Accessories" section for more information.
14