Table of Contents
Advertisement
WARNING
AVOID SERIOUS INJURY ORDEATH
• GO UP AND DOWN SLOPES,
NOT ACROSS.
• AVOID SUDDEN TURNS.
• DO NOT OPERATE THE UNIT WHERE IT COULD SLIP OR TIR
• IF MACHINE
STOPS GOING UPHILL,
STOP BLADE(S)
AND BACK
DOWNHILL
SLOWLY.
• DO NOT MOW WHEN CHILDREN
OR OTHERS ARE AROUND.
• NEVER CARRY CHILDREN,
EVEN WITH BLADES
OFF.
• LOOK DOWN AND BEHIND BEFORE AND WHILE BACKING.
• KEEP SAFETY DEVICES
(GUARDS,
SHIELDS, AND SWITCHES)
IN
PLACE AND WORKING.
• REMOVE OBJECTS
THAT COULD BE THROWN
BY THE BLADE(S).
• KNOW LOCATION
AND FUNCTION
OF ALL CONTROLS.
• BE SURE BLADE(S)
AND ENGINE ARE STOPPED
BEFORE
PLAC-
ING HANDS OR FEET NEAR BLADE(S).
• BEFORE
LEAVING
OPERATOR'S
POSITION,
DISENGAGE
BLADE(S),
PLACE
THE
SHIFT
LEVER
IN NEUTRAL,
ENGAGE
BRAKE LOCK, SHUT ENGINE OFF AND REMOVE KEY.
READ OPERATOR'S MANUAL
DrivingOnSlopes
Refer to the SLOPE GAUGE on page 7 to help determine
slopes where you may operate the tractor safely.
,_
WARNING:
Do not mow on inclines with a
slope in excess of 15 degrees
(a rise of
approximately
2-1/2 feet every 10 feet). The
tractor
could
overturn
and cause
serious
injury.
•
Mow up and down slopes, NEVER across.
•
Exercise extreme caution when changing direction
on slopes.
•
Watch for holes, ruts, bumps, rocks, or other
hidden objects. Uneven terrain could overturn the
machine. Tall grass can hide obstacles.
•
Avoid turns when driving on a slope. If a turn must
be made, turn down the slope. Turning up a slope
greatly increases the chance of a roll over.
•
Avoid stopping when driving up a slope. If it is
necessary to stop while driving up a slope, start up
smoothly and carefully to reduce the possibility of
flipping the tractor over backward.
Setting TheCruiseControl
•
Place the shift lever in the FORWARD position,
then slowly depress the drive pedal until the desired
speed is achieved.
•
Lightly depress the cruise control button.
•
While continuing to hold the cruise button in, lift
your foot from the drive pedal (you should feel the
cruise latch engage).
•
Once engaged, the cruise control button and the
drive pedal will lock in the "down" position, and the
tractor will maintain the same forward speed.
NOTE:
Cruise control can not be engaged at the
tractor's fastest ground speed. If the operator should
attempt
to
do
so,
the
tractor
will
automatically
decelerate to the fastest optimal mowing ground speed.
Disengage the cruise control using one of the following
methods:
•
Depress the brake pedal to disengage the cruise
control and stop the tractor.
•
Lightly depress the drive pedal.
To change to the reverse direction when operating with
cruise control, depress the brake pedal to disengage
the cruise control and bring the tractor to a complete
stop. Then place the shift lever in the REVERSE
position and depress the drive pedal.
Engaging the Blades
Engaging the PTO (Blade Engage) transfers power to
the cutting deck or other (separately available)
attachments. To engage the blades, proceed as
follows:
•
Move the throttle control lever to the FAST (rabbit)
position.
•
Grasp the PTO (Blade Engage) lever and pivot it all
the way forward into the engaged (ON) position.
•
Keep the throttle lever in the FAST (rabbit) position
for the most efficient use of the cutting deck or other
(separately available) attachments.
IMPORTANT: The engine will automatically shut off if the
PTO is engaged with the shift lever in position for
reverse travel with the ignition key in the NORMAL
MOWING position. Refer to SafetyInterlockSwitches on
page 12.
Using the DeckLift Lever
To raise the cutting deck, move the deck lift lever to the
left, then place it in the notch best suited for your
application. Refer to Setting TheCutting Height earlier in
this section.
14
Hide quick links:
Advertisement
Table of Contents
