Table of Contents
Advertisement
Video
and audio
are out of sync
*
If you've connected a device, sucll as a DVD playel, to your TV's Video jack, and to an audio receiver using tile audio jacks, you may experience a
slight delay between tile audio heard and tile video seen. Connect the DVD player to the TV's Audio jacks, then use the TV's FIXED/VARIABLE
AUDIO OUTPUT jacks to connect to an audio receive1:
If your TV is connected to an audio/video (A/V) receiver or home theatre system via tile DIGITAL AUDIO OUT jack, read tile following information.
*
If you've connected a device to your A/V receiver, such as a DVD player or satellite receive1;you may experience a slight delay between tile audio
heard and tile video seen. This occurs because tile digital audio is sent directly to the speakers while the video must be processed inside tile TV before
it is displayed.
°
If tile device has Component Video (Y, Pb, Pr) jacks, connect these jacks to tile TV's Y, Pb, Pr jacks to minimize tile discrepant?: This works best if
the device supports Progressive Scan technolog>
"
If necessar> you can connect the device directly to tile TV using L/R audio jacks and bypassing the A/V receiver or you can program an audio delav
in tile A/V receiver so the audio and video match up (not all audio equipment has tile ability to program delays). Check tile Audio/Video Receiver's
manual.
Blank
screen
*
Make sure you have connected the device to the TV correctl}_
*
Make sure tile device connected to tile TV is turned on and tuned to the corresponding Video Input Channel.
°
Try another channel, or press the INPUT or ANT'CAB button.
*
\Vhen you first turn off your TV, the screen fades from blue to black. Once the screen goes black, the TV's interiml lamp starts its cool-down cycle.
If you try to turn on the TV during tile cool-down cycle, tile TV turns back on and you!ll hear audio, but the picture will take a few moments to be
displayed.
Unusual
sound
quality
"
Check tile G_r_21_i," Eqmllize_: So_md EvFaF_siorl, 5_qPand Soltr_dLogic settings.
"
Check if SAP is turned oil.
*
Check that tile Al¢dio Lar_g:l M ode or ._)qPis set to your language.
Humming
or buzzing
noise
*
The TV is in its lamp cool-down cycle. To prolong tile life of"tile TV's lamp system, the TV must warn1 up and cool down properly. You may notice
additional noise during these cycles.
"
Maybe the speakers are turned of'f" Check the FIXEf)/VAR[ABLE O{/Tcontrol panel in the Altdio menu.
No picture,
sound
okay
"
If"tile indicator oil the fl'ont of"tile TV is blinldng for one minute, the lamp inside of your TV may need to be changed. Refer to the l'oz_e_" i r_dicatoris
bliF#_ir_g o </iashiJ_g section on tile previous page for more information.
°
You might [lave tried to turn on tile TV during lamp cool-down. Wait a few moinents and tile picture will be displayed.
No sound,
picture
okay
*
Maybe tile sound is muted. Try pressing tile volume up button to restore sound.
*
Maybe tile speakers are turned of'f'in tile Al_dio menu. Check tile FIXED/VARIABLE OUTcontrol
panel in the AdiJaF_cedAltdiomenu.
*
If using an S-Video, component or composite video connection, remember to also coimect tile device's L and R AUDIO OUT jacks to tile TV's L
and R INPUT jacks.
*
Check tile Mrra'iJ.mH.J_
I&h¢_e and Sta*'mp I&!zm_e s ettings in tile Ad_:ar_ced Al¢dio nlenu.
Channel
search
finds
few
channels
•
The cable coimected to tile (;ABLE and/or ANTENNA INPUT jack might be loose.
•
Your of'f'air antenna might be getting a weak signah Move it higher or get a bigger antenna.
•
If you have cables connected to tile CABLE and ANTENNA jacks, try swapping tile cables. (;able needs to be connected to the CABLE INPUT; off'-
air antenna needs to be connected to the ANTENNA INPUT.
•
If you have a cable box, you can't connect it to the ANTENNA jack. Connect it to tile CABLE INPUT or a Video Input jack.
•
Select all the options in tile CT*a*me/&,an'hmenu, and retry chaimel search.
G4
Chapter 5
Advertisement
Table of Contents
