Table of Contents
Advertisement
i
RECORDING
RELAY RECORDING
(CT-W803RS/
CT-W703RS)
(from DECK I to DECK II)
2
3
4
5
7
1
1. Load tapes
for recording
in DECK I and DECK II.
2. If you use AUTO
BLE tuning,
see page
15.
3. Set the DOLBY
NR ON/OFF
switch
and set the DOLBY
NR switch.
4. Set the REV MODE
switch
to _-_.
5. Press the recording
(e)
button
of DECK I.
6. Prepare
the audio source
from
which
you wish
to re-
cord. Turn
on the stereo
amplifier
and prepare
it for
playback
of the desired
audio source.
7. Adjust
the
recording
level.
For details,
see page
14
"ADJUSTING
THE RECORDING
LEVEL".
8. Press the playback
(•
or <) button
of DECK I to begin
recording.
•
When recording on both sides, press the b" button. If the •
button is pressed, recording will stop after only one side is
recorded.
•
When the tape in deck one ends, the other deck automati-
cally begins recording.
NOTES:
•
When
erasure
prevention
tabs
are
broken,
you
cannot
record
even if you press
the recording
(o)
button.
•
You cannot
relay-record
from
DECK
II to DECK L
To stop
recording
temporarily
Press the pause ( I II ) button of the operating deck.
•
To resume recording,
either press the pause (11 II) button again,
or press the playback (b" or •) button.
To stop
recording
Press the stop (11) button of the operating deck.
RELAY RECORDING
SEQUENCE
WITH
REVERSE
MODE SWITCH
SETTING
The recording
sequence
depends
on the setting
of the REV MODE
switch
and on which
playback
(b" or •)
button
is pressed
first.
The
recording
sequence
for
each
possible
selection
is shown
below.
•
Relay
recording
always
begins
from
the direction
indicated
by
the tape
transport
indicator
( [> or <3 ). To change
this direc-
tion,
press
the desired
playback
(b" or •)
button,
then
immedi-
ately
press
the stop
(11) button.
ID
: DECK I forward
recording
1<3 : DECK I reverse recording
lid
: DECK II forward
recording
11<3 : DECK II reverse recording
oo
: Auto-reverse
function
: Relay
REV
Starting
Another
MODE
playback
deck
Recording sequence
switch
button
mode
DECK lb"
II•
ID ooi<3_lll>ooli<:3
DECK Ib"
II•
I_ oo1<3_11<3
_-)
DECK I•
lib"
1<3 _IID
oo11<3
c--,J
DECK I•
I1•
1<3 _11<3
[ PARALLEL
RECORDING
(CT-W803RS
only)
J
2103
42
1
85
7
1
1. Load tapes
for recording
in DECK I and DECK II.
2. If you use AUTO
BLE tuning,
see page 15.
3. Set the type
of the DOLBY
NR ON/OFF
switch
and set
the
DOLBY
NR switch.
4. Set the REV MODE
switch.
•
To record on one side only, set the switch
to the------posi-
tion. To record on both sides, set the switch to either the ----_
or the (-".,-J position.
5. Press the recording
(e)
button
of DECK I.
6. Prepare
the audio source from
which
you wish to rec-
ord.
Turn
on the
stereo
amplifier
and
prepare
it for
playback
of the desired
audio
source.
7. Adjust
the
recording
level.
For details,
see page
14
"ADJUSTING
THE RECORDING
LEVEL".
8. Press the stop (e) button
of DECK |.
9. Set the tape
transportation
direction
for recording
Parallel recording is always begun from the direction
indicated
by the tape transport
indicator
(b" or •). To change this direc-
tion, press the desired playback
button (b'or
•), then immedi-
ately press the stop (11) button.
10. Press PARALLEL
REC button.
Both DECK I and DECK II start recording the same sound
source.
16
<RRB1143>
En
Hide quick links:
Advertisement
Table of Contents
