Page 1
M4c,,.es OPERATOR'S MANUAL Models 587 and 588 IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimpr'oved forest- covered, brash-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any).
SECTION 1: FINDING YOUR MODEL NUMBER This Operator's Manual is an important part of your new edger. It will help you assemble, prepare and maintain your edger. Please read and understand what it says. Before you start to prepare your edger for its first use, please locate the model plate and copy the information from it in this Operators Manual.
SECTION 3: IMPORTANT SAFE OPERATION PRACTICES WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY YOURSELF OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE YOUR EDGER. FAILURE TO COMPLY WITH THESE INSTRUCTIONS...
Page 4
• Make sure engine is off and spark plug wire is • After striking a foreign object, shut off the engine, disconnected when clearing jammed material from make absolutely sure the blade and aU moving blade. parts have completely stopped, disconnect spark plug wire to prevent accidentaJ starting, then •...
SECTION 4: SET-UP INSTRUCTIONS IMPORTANT: Insert opposite end of clutch rod into the hole in This unit is shipped WITHOUT the pivot arm extension. Affix with flat washer GASOLINE or OIL. After setting up the unit, and hairpin clip provided. See Figure 1, Inset B. service engine with...
Page 6
SECTION 5" CONTROLS THROTrLE CONTROL When the blade is adjusted toward the horizontal position, the front wheels must also be adjusted, The throttle control lever is located on the engine. It Remove the hairpin clip on the left side and slide the allows the engine to run and also stops the engine.
SECTION 6: OPERATION STOPPING THE ENGINE The operation of any edger result in foreign objects being To stop the engine, move throttle control to the OFF thrown into the eyes, which position. Disconnect and ground the spark plug wire result severe damage, to prevent accidental starting while equipment is...
Engine--Refer to engine manual lubrication instructions. SECTION 8: MAINTENANCE WARNING: Disconnect the spark plug wire ground against engine before performing adjustment, repairs or maintenance. Figure 8 ENGINE To edge along a curb, remove the hairpin clip from the right side of the front axle, slide the Refer to engine manual for complete instructions for right wheel toward the left side of the unit and care and maintenance of engine.
SECTION 9: OFF-SEASON STORAGE The following steps should be taken to prepare unit Store unit in a dry, clean area. Do not store next for storage, to corrosive materials, such as fertilizer. Clean and lubricate unit thoroughly. NOTE: When storing any type of power equipment in a poorly ventilated or metal storage shed, care Refer engine manual...
Page 10
Models 587 & 588 NOTE: Adjustable curb wheel is NOT standard on aft units. IMPORTANT: For a proper working machine, use Factory Approved Parts. V-BELTS are specially designed to engage and disengage safely. A substitute (non-OEM) V-Belt can be dangerous by not disengaging completely.
Page 11
Models 587 & 588 Ref. Ref. PART NO DESCRIPTION PART NO DESCRIPTION 720-0283 756-0449 Grip 3/8" "V"-Pulley 712-0107 Hex L-Nut 1/4-20 Thd. 754-0142 "V"-Belt 714-0104 Cotter Pin 5/16" Dia. 710-0929 Hex Bolt 5/8-18 x 4.5" Lg. 710-0106 Hex Bolt 1/4-20 x 1.25" Lg. 710-0258 Hex Bolt 1/4-20 x .625"...
MANUFACTURER'S LIMITED WARRANTY FOR: For TWO YEARS from the date of retail purchase products sold or exported outside of the United within the United States of America, its possessions States of America, its possessions and territories, and territories, MTD PRODUCTS INC will, at its except those sold through MTD PRODUCTS INC's...