Advertisement
Basic Lighting Procedures
Machine oils used in the manufacturing process of
stainless steel can cause stainless steel to turn a tan
color. Before initialgrill use, remove protective PVC
film from Control Panel and inside and outside of Grill
Lid. Use a Stainless Steel Cleaner to polish the
stainless steel and remove these excess oils from
your grill. Never use abrasive cleaners or scrubbers
because they wilt scratch and damage your gdll. For
details, see Cleaning
Exterior
Stainless
Steel
Surfaces on page 18.
Gas Lighting Instructions
Familiarize yourself with the safety guidelines at the
front of this manual. Do not smoke while lighting grill or
checking gas supply connections.
1. If you have a LP gas gdll be sure the LP gas tank
is filled, or if you have a NG grill be sure that the
locking shut off valve is open.
2. Check that the end of each Burner Tube is propedy
located over each Valve Orifice.
3. Be sure all gas connections are securety tightened.
4. Open the Grill Lid or Side Burner Lid, depending
on the Burner you are lighting.
WARNING
Failure to open Grill Lid during the
lighting
procedures
could result in a fire
or explosion
that could cause serious
bodily
injury, death,
or property
damage.
5. Set ALL Control Knobs to OFF, and for LP Models,
open gas tank valve slowly until 1/4 to 1/2 open.
OFF
Open LP
gas tank
\
6. Push and turn the LEFT Control Knob to HIGH.
HIGH
OFF
7. Immediately
press the Electric
Ignitor for 3-4
seconds
to light the Burner.
\_\
PRESS
.
9.
If the burner does not light, turn the Control Knob
to OFF, wait 5 minutes for gas to clear, then retry.
Once the left gdll burner is ignited, the adjacent
burner can be lit by simply turning its Control Knob
to HIGH.
10. Adjust Control Knobs to your desired cooking
temperature.
Side Burner Lighting Instructions
1.
Follow steps 1 through 5 of the Gas Lighting
Instructions.
2.
Push and turn the control knob for Side Burner to
HIGH.
HIGH
RIGHT
ELECTRIC
IGNITOR
OFF
(for SIDEBURNER)
_
_UEL
GAUGE
ISPL_
@ @ @°@ @
SIDE
BURNER
3.
Immediately press the electric ignitor for 3-4
seconds to light the burner.
4.
If the burner does not light, turn the control knob to
OFF, wait 5 minutes for gas to clear, then retry.
5.
Adjust control knobs to your desired cooking
temperature.
Back Burner Lighting Instructions
Note: The location of the Back Burner makes it more
susceptible to winds that wilt decrease the perfor-
mance of your rotisserie cooking. For this reason you
should not operate the Back Burner during windy
weather conditions.
1.
Follow steps 1 through 5 of the Gas Lighting
Instructions.
2.
Open the Gdll Lid. Failure to do so can result in
fire or explosion. See WARNING left.
3.
4.
5.
6.
7.
.
16
Set ALL Control Knobs to OFF and open the LP
gas tank valve slowly until 1/4 to 1/2 open.
Push and turn the Right Control Knob for Back
Burner to HIGH.
Then immediately
press the Electric Ignitor for
3-4 seconds to light the Back Burner.
If the Burner does not light, turn the Control Knob
to OFF, wait 5 minutes for gas to clear, then retry.
Once lit, the Back Burner will reach cooking
temperature quickly. The orange/red glow will even
out in about 5 minutes.
For best results, always rotisserie cook with the
grill Lid down and the Back Burner Control Knob
set to HIGH. Do not use the main gdll Burners
when the Back Burner is in operation.
Advertisement
