Husqvarna 55R21HV Owner's Manual page 15

SERVICE AND ADJUSTMENTS
2. Route the other end of the new drive belt through hole
in housing.
3. Reattach debris shield to housing with screw previ-
ously removed. Be sure tab of debris shield is in gap
of housing.
4. Position blade on the blade adapter aligning the two
(2) holes in the blade with the raised lugs on the
adapter.
5. Be su re the trailing edge of blade (opposite sharp edge)
is up toward the engine as shown (See Fig. 20).
6. Install the blade bolt with the lock washer and hardened
washer into blade adapter and crankshaft.
7. Use block of wood between blade and lawn mower
housing and tighten the blade bolt, turning clockwise.
• The recommended tightening torque is 35-40 ft. lbs.
IMPORTANT: BLADEBOLT ISHEATTREATED.IF BOLTNEEDS
REPLACING,REPLACEONLYWITHAPPROVEDBOLTSHOWN
IN THE REPAIR PARTS SECTION OF THIS MANUAL.
8. Return mower to upright position.
9. Install new drive belt into idler arm assembly, then
around the drive pulley. Be sure belt is inside of belt
keepers (See Fig. 19).
NOTE: Pulling on the drive belt (to install it on the drive
pulley) will cause the other end of the belt to free itself from
the debris shield retainer and come into contact with the
pulley end of the blade adapter.
10. Reattach drive cable spring to the idler arm assembly,
then reattach drive cable to anchor.
11. Reattach drive cover with screws previously removed
(See Fig. 18).
12. Connect spark plug wire to spark plug.
TO ADJUST HANDLE
(See Fig. 22)
The handle on your lawn mower has multiple height posi-
tions - adjust to height that suits you.
1. Remove knob and carriage bolt on one side of the
lower handle.
2. While holding handle assembly, remove knob and car-
riage bolt from opposite side, align hole in handle with
desired hole in handle bracket and reassemble bolt and
knob and tighten securely.
3. Align opposite side of handle with same positioning
hole and secure with bolt and knob.
LOW
HIGH
-HANDLE
BRACKET
FIG. 22
ENGINE
Maintenance, repair, or replacement of the emission con-
trol devices and systems, which are being done at the
customers expense, may be performed by any non-road
engine repair establishment or individual. Warranty repairs
must be performed by an authorized engine manufacturer's
service outlet.
ENGINE SPEED
Your engine speed has been factory set. Do not attempt to
increase engine speed or it may result in personal injury. If
you believe that the engine is running too fast or too slow,
take your lawn mower to an authorized service center for
repair and adjustment.
CARBURETOR
Your carburetor is not adjustable. If your engine does not
operate properly due to suspected carburetor problems,
take your lawn mower to an authorized service center for
repair and/or adjustment.
IMPORTANT: NEVERTAMPERWITHTHE ENGINE GOVERNOR,
WHICH IS FACTORY SET FOR PROPER ENGINE SPEED.
OVERSPEEDING THE ENGINE ABOVE THE FACTORY HIGH
SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE
ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING,
CONTACTYOUR NEARESTAUTHORIZED SERVICE CENTER,
WHICH HAS PROPER EQUIPMENT AND EXPERIENCE TO
MAKE ANY NECESSARY ADJUSTMENTS.
STORAGE
Immediately prepare your lawn mower for storage at the end of the season or if the unit will not be used for 30 days or more.
LAWN MOWER
When lawn mower is to be stored for a period of time, clean
it thoroughly, remove atl dirt, grease, leaves, etc. Store in
a clean, dry area.
1. Clean entire lawn mower (See "CLEANING" in the
Maintenance section of this manual).
2. Lubricate as shown in the Maintenance section of this
manual.
3. Be sure that all nuts, bolts, screws, and pins are se-
curely fastened. Inspect moving parts for damage,
breakage and wear. Replace if necessary.
4. Touch up all rusted or chipped paint surfaces; sand
lightly before painting.
15