Table of Contents
Advertisement
websitehttp:Ywww,lgservice.com
e-mail http:Ywww.lgeservice.com/techsu p.html
E
'S
U
ITI
L
Please, read the operating
instructions
and safety precautions
carefully
and thoroughly
before
installing
and operating
your
room air conditioner.
MANUEL 'UTILIS
CLI
TISE
E F
Veuillez life a_entivement
et en entier ce guide d'utilisation
et les mesures
de securite
ci-incluses
avant de proceder
I'installation
et au fonctionnement
de votre clirnatiseur.
NE
I N
A
ET E
I
L
IC!ONA
EL
Por favor lea las instrucciones
de operacion
y las precauciones
de seguridad
cuidadosa
y totalmente
antes de instalar y operar
su acondicionador
de aire de ventana.
I0
MODELS, MOIDELES, MODELO::
R1402, R1802, R2102, R240,2, R1803, R2103, R2403
Advertisement
Table of Contents
Related Manuals for Goldstar R1402
Summary of Contents for Goldstar R1402
- Page 1 websitehttp:Ywww,lgservice.com e-mail http:Ywww.lgeservice.com/techsu p.html Please, read the operating instructions and safety precautions carefully and thoroughly before installing and operating your room air conditioner. MANUEL 'UTILIS ET E TISE Veuillez life a_entivement et en entier ce guide d'utilisation et les mesures de securite ci-incluses avant de proceder...
-
Page 2: For Your Records
FOR YOUR RECORDS Staple your receipt to this page in case you ne_ it later. Write down the. model and serial numbers here: Model # You can find them on a label on the side of each unit. _aler's Name Date Purchased READ THIS MANUAL Inside you will find many helpful hints on how to use and... - Page 3 fety Pre utions To prevent injury to the user or other p_pie and property damage, the following instructions must be follow_. m Incorrect operation due to ignoring of instruction will cause harm or damage+ The seriousness is classified by the following indications. WARNING "...
- Page 4 c ,o.1 , It may cause an injury, • Water may enter the unit , An oxygen shortage may occur. degrade t6e insulation. It may cause an e]ectr[,c shock. . Do not use this air _ndifloner ,Since the fan rotates at high .
-
Page 5: On The Air Conditioner
About the ntrols on the Air Conditioner The controls will look like one, of the following. - Turns air conditioner off. o Med speed fan operation without cooling. Low _n o Low speed fan operation without cooiing. High COol o C_ling with high speed fan operation.. -
Page 6: Air Direction
Additional controls and important information. The ventilation lever must be in the CLOSE _sition in order to maintain the best cooling _nditions. When fresh air is necessary in the room, set the ventilation lever to the OPEN position. The damper is opened and room air is drawn out. NOTE: Before using the ventilation feature, poslti,on the lever, as shown. -
Page 7: Air Filter Cleaning
How to Connecta Drain Hose A drain hole iis provided at the rear of the air _ndit:ioner unit. Fig. 1 Select a drain method according to the foilowing PiPE DRAIN 1. Remove the hole rubber from the base-pan. (for some models) , ......3. - Page 8 Features and In allation Learning parts name prior to installation will he!p you understand the installation procedure. 1. CABINET 7. AIR FILTER 2. HORIZONTAL AIR DEFLECTOR 8. CONTROL BOARD (VERTICAL LOUVER) 9. POWER CORD 3. VERTICAL A_R DEFLECTOR 10. EVAPORATOR (HORIZONTAL LOUVER) 11.
-
Page 9: How To Install The Unit
How to Install the Unit INSIDE OUTSIDE FENCE AWNING FOAM ... ¸¸.¸4 1/4 Bubble RADIATION COOLE_I HEAT ._:._ ..About 1/2" Over 20" 1. To avoid vibration and noise, make sure the unit: is installed securely and firmly. 2. Install the unit where the sunlight does not shine directly on the unit. if the unit receives direct sunlight, build an awning to shade the cabinet. -
Page 10: Window Requirements
WindowRequirements NOTE: Al! supporting parts should be secured to firm wood, masonry, or metal. WINDOW REQUIREMENTS 1. This unit is designed for installation 26" to standard double hung windows with actual 8" min opening widths from 26" to 41". Stool The top and botom window sashes must... -
Page 11: Suggested Tool Requirements
Suggested Tool Requirements SCREWDRIVER(+,-), RULER, KNIFE, HAMMER, PENCIL, LEVEL PREPARATION OF CHASSIS Shipping screws 1. Remove the screws which fasten the cabinet at _th sides and at the back. 2, Slide the unit out from the cabinet by gripping the base pan handle and pulling... -
Page 12: Cabinet Installation
Cabinet Installation 1. Open the window, Mark a line on the center of the window stool between the side Sill Bracket window stop moldings. Loosely attach the sill bracket to the support Carriage Bo_t bracket using the carriage bolt and the lock (M-Screw) nut. - Page 13 5. Pull each Frame curtain fully to each window sash track, and pull the bottom window sash down behind the Top retainer bar until it meets. 6. Attach each Frame curtain the window saslh by using screws (Type C.) (See Fig. 10) Fig.
-
Page 14: Use Of Extension Cords
Data(For 115V model only) Line Cord Plug Use Wall Receptacle Power Supply Do not under any _ .._ Jcircumst_ces Use 15 AMP. time _4._, or remove delay fuse or 15 AMP. ._'_ZD// grounding prong ¢ from the pklg. circuit breaker. Power supply cord with Standard 125V, 3-wire grounding... -
Page 15: Abnormal Operation
fore Troubleshooting Tips Save, time and money! Review the chart below first and you may not ne_ to cal! for service. • You may hear a pinging noise caused by water being picked up and thrown against the condenser on rainy days or when the humidity is high. This design feature helps remove moisture and improve efficiency •...