Hitachi CP-X970W User Manual page 10

Names and functions of each part (continued)
Remote control transmitter
VIDEO, RGB button _ _ LASER button
Press to switch the input. (Refer to page 13, 19.) VEOEO Turns the laser beam on and off. Refer to page
11 conceming usage and observe the cautions.
STANDBY / ON button _ sTAN_B¥/oN_ PosmoN
* POSITION button
_ PressPosition, t henusethe mouse DiskPadto adjust
Used to turn the power on and off.
Press for 1 sec. or more to turn the power off
(enter standby status).
(Refer to pages13 and 14.)
$ DISK PAD / MOUSE button *4
(1) Used to select menu items when the menu
screen is displayed (refer to page 18 - 18).
(2) When the menu is not displayed, the mouse
shift function and left click function are active.
*t (3)After the POSITION button has been
pressed, the screen can be moved upward,
downward and ght.
the image position (RGB mode only).
(Refer to page 16.)
_¢
RESET / MOUSE RIGHT button
(1)Operates as the RESET batten when the menu
is displayed. Press this button to return to the
initial settings,
(2)Used to click the right mouse button when the
menu is not displayed (refer to page 25,26).
*t (3)Pressing this button after scrolling the screen
with POSITION returns the screen to the original
* MENU button
Used to turn the menu screen display on and off.
(Refer to page 17 - 21.)
¢ MAGNIFY button
Used to magnify the displayed=msge.
(Refer to page 16.)
* P in P button "2
Used to turnP in P (Picture In Picture: displays sub video
signal images in the RG8 signal) on and off.
Each time this button is pressed, operation will change in
the following sequence:
(1)
(1)- (3) t
(Refer to page 20.)
BLANK button
Used to turn blanking on and off.
(Refer to page 20.)
FOCUS button
Used to adjust the focus of the image on the
screen. (Refer to page 13.)
button
Used to turn the freeze (still) image display on and off.
(Refer to page 15.)
VOLUME button
Adjusts the volume of the sound. Press [/\] to
increase the volume and (V) to decrease the volume.
When there is no video signal input, operation is not
possible when the input video signal is outside the
sync range,
button
Applies Mute. (Press the Play button again to
cancel.)
TIMER button
Turns the display of the time set with the Timer
on the Menu screen on and off.
The timer is not displayed when no input signal
is detected or when SYNC is out of range or
during blanking or during freezing.
Refer to page 21 concerning the method used to
set the timer.
ZOOM button
Used to adjust the size of the image. (Refer to
page 13.)
* AUTO button
Used to execute auto-adjust.*3
*These functions do not operate when initial screen message "NO INPUT IS DETECTED" or "SYNC IS OUT OF RANGE" is displayed.
*1 POSITION icon
When the POSITION button is pressed, the moving display icon
will appear at the bottom right of the screen.
While displaying the icon, you can operate POSITION.
*3 Auto adjustment function
The projector automatically adjusts 4 items (V. POSIT, H. POSIT,
H. PHASE, H. SIZE).
When you choose AUTO (move the cursor to the right from the
manual operation position), the AUTO confirmation menu shown
below is indicated.
*4 Disk Pad method of operation
• Move and select by tilting Disk Pad in the required direction.
• Press Disk Pad in to realize the function of the mouse left
button.
• A mouse cable is necessary if a mouse is to be used.
(Refer to pages 26, 27.)
"2 p in P function
With the P in P function, signals are input to both RGB and
VIDEO. This function operates only when the RGB signal has
been selected. There is no display in the case of the no signal and
when the RGB signal is outside the sync range.
When P in P is used, audio is automatically switched to video.
In P in P, audio input can be switched by pressing the VOL /\and
VOL _/keys of the remote control, displaying the audio bar and
moving DiSK PAD left and right during the display.
E_ _ RGB/VIDEO
10