Advertisement
Operating
Instructions
5"tai_d_ss
5't_el
H@'ig'erator
7 mperature
controls
.............
.......
..........................
The t(,mp(,ratur,_ co_mz)£ mz, p_z_(_ti,_ tM f!zcto U at 37°Ff!)r the f!>_hji)od compart'me_t
and O°F /i_r the /iz,(,z_,rcom/,artm_,_t. Allow 24 hom:Lf!_r the temp_,ratuw to stabilize to the
p'r(<_et r (_comm_,_dedsettinK_.
77_e tem/,_,ratu_z, contro£ _can display both the SET tem/,_,ratur_, as wall a.s the actual
tem/,_,ratur(, in the,/)(_h,/bod and,f!_,(,z_,r com/,artm_,,_ts. The a_tual temp_,ratur(, mcO, va U
.4igl_tlyjiom the SET temp_ratu_z_ based on u._ag_(_ a nd op_,rating _nvironm_,_t.
Setting eitMr or both contro£ to OFF stop.s coolb_ in both the f!(,(,zer a,_d /i(,sh fred
com/,avt'm(,_t._; but does not .shut qff el(,chJcal powder to the r@ig_,rato'_:
NOTE:
The _J_it4(,mtor z.sshipped with p_;t_,ctive film (v;v_,ring the temp(,ratur(_ contm£.
(!thi.Lfilm
was not r(_mow,d during installation,
wmove it now.
To chmage
the temperature,
press
and
release
tile
_._ARMER
or COI,DER
pad.
Tile
SET light
will
come
on and
tile display
will show
the set
temperature.
To change
the teinperature,
tap
either
tile _;_RMER
or COI,DER
pad
tmfil
tile
desired
temperatm'e
is displayed.
Fresh
tood
temperatures
can be a(!j usted
between
34°F and
44°F and
the
fl'eezer
temperatures
can be
a(!iusted
between
-6°F and
+6°F.
Once
tile desired
temperature
has been
set, the
temperature
display
will return
to tile actual
fl'esh
fi)od
and
fl'eezer
temperatm'es
after
5 seconds.
Several
a(!jusunents
may be required.
Each
time
you at!just
controls,
allow
24 hom_
tot tile
retiigemtor
to reach
the temperature
you
have
set.
To turn
the cooling
system
off, tap the
X_;M_MER
pad
fi)r either
the fl'esh
fl)od
comi)artmei_t
or the
fl'eezer
until
tile display
shows
OFF.
To turn
the
refit back
on, press
the
COI,DER
pad
t0r either
the fl'esh
tbod
compartment
or fl'eezet:
The
SET
light will ilhmfinate
on the side
you selected.
Then
press
the
COI,DER
pad
again
(on
the
side where
the
SET light
is illuminated)
and
it will go to the
preset
points
of 0°F fiw tile fl'eezer
and
37°F tot
tile fl'esh
fi)od
compartment.
I_ (?t'/o I¥lZ gl fl ("g
Air How
System
Tile
PerIommnce
_d>[qow
System
is designed
m
maximize
temperature
control
in tile fl'esh
fi)od
and
fl'eezer
compartments.
This
mfique
special
teattlI'e
consists
ot tile _di" Tower
along
tile top
and
back
walls _ff tile ti'esh
tood
compartment
and
tile _Mr Tmmel
on tile bottom
portion
of tile
fl'eezer
rear wall. Placing
fl_od in fl'ont
oI tile
louvers
on these
components
will not affect
petti)mmnce.
Mthough
tile Mr Tower and the
_dr Tmmel
can be rein oved, doing so will affect
temperature
pe_ti)rmance.
(For removal
instructions,
ondine,
24 horn's a da> contact
us
at w_:monogram.com
or call 800.444.1845.
In Canada,
call us at 1.888.880.3030.)
Advertisement
