Advertisement
Available languages
Available languages
INSTALLATION
Choose
a convenient
location
for installation.
It should
be at eye
level,
reachable
by the
shortest
person
who will
use it, and within
sight
of the door.
For a one-piece
door,
choose
the optional
location
shown
in the
illustration
to avoid
injury as the door
swings
up and out.
Keypad
Typical
Installation
Exterior Front Wall
1-Piece or
Sectional
Door
"_ Door Jamb Edge
(Optional
Location
for 1-Piece Door)
Door Jamb Face
SECTIONAL
DOOR ONLY
, KEYPAD MUST BE INSTALLED
WITHIN SIGHT OF THE DOOR
Test the reception
of the Keyless
Entry
by operating
your
opener
from the selected
location.
Change
the location
if
necessary.
Remove
the battery
cover to access
the bottom
mounting
hole:
•
Insert
a small
phillips
screw
driver
into the small
hole at the bottom
of
the cover
and gently
pull outward
to
loosen.
•
Slide the cover
down to remove.
Center
the keypad
at eye level against
Bottom
mouetinc
the selected
location.
Mark 4-1/4"
(10.8 cm) up the centerline
from the
bottom
and drill a 1/8" pilot hole.
Install
top mounting
screw,
allowing
1/8" (3 mm) to protrude
above
Battery
surface.
Position
keypad
on screw
Cover
head
and adjust
for snug fit.
With cover open
so bottom
mounting
hole is visible,
use a
punch
to mark hole.
Remove
keypad
and drill 1/8" pilot hole.
Replace
keypad
and complete
installation
with bottom
screw,
using care to avoid cracking
plastic
housing.
Do not overtighten.
To replace
the battery
cover,
insert the lip at the top and snap
in place.
THE KEYLESS
ENTRY BATTERY
To prevent possible SERIOUS INJURYor DEATH:
• NEVERallow small children near batteries.
• If battery is swallowed, immediately notify doctor.
The 9 volt battery
should
produce
power
for at least one year. Replace
when the keypad
illumination
becomes
dim.
Dispose
of old batteries
properly.
TO CHANGE
AN EXISTING,
KNOWN
PIN
If the existing
PIN is known,
it may be changed
by one person
without
using a ladder.
1. Press
the four buttons
for the present
PIN, then press
and
hold the # button.
The opener
light will blink
twice.
Release
the # button.
2. Press
the new 4-digit
PIN you have chosen,
then
press
Enter.
The motor
unit lights
will blink once when
the PIN has been
learned.
Test by pressing
the new PIN, then press
Enter. The door
should
move.
TO SET A TEMPORARY
PIN
You may authorize
access
by visitors
or service
people
with a
temporary
4-digit
PIN. After a programmed
number
of hours
or
number
of accesses,
this temporary
PIN expires
and will no
longer
open the door. It can be used to close the door even
after it has expired.
To set a temporary
PIN:
1. Press the four buttons
for your personal
entry
PIN (not the
last temporary
PIN), then
press and hold the _ button.
The opener
light will blink
three times.
Release
the button.
2. Press
the temporary
4-digit
PIN you have chosen,
then press
Enter.
The opener
light will blink four times.
3. To set the number
of hours
this temporary
PIN will work,
press the number
of hours
(up to 255), then press
_.
OR
3. To set the number
of times
this temporary
PIN will work,
press the number
of times
(up to 255), then press
#.
The opener
light will blink
once when the temporary
PIN has
been
learned.
Test by pressing
the four buttons
for the temporary
PIN, then
press
Enter. The door should
move.
If the temporary
PIN was
set to a certain
number
of openings,
remember
that the test
has used
up one opening.
To clear the temporary
password,
repeat
steps
1-3, setting
the number
of hours
or times to 0 in
step 3.
SPECIAL
NOTE:
The temporary
password
can ONLY be
programmed
to keypads
working
on a Craftsman
® Garage
Door
Opener.
It WILL NOT work on keypads
programmed
to an
external
receiver.
The temporary
password
will continue
to CLOSE
the door even
after the time has expired.
To eliminate
this, program
a new
temporary
password
into the keypad.
Replacement
parts:
Keypad cover .......................................
31D431
Battery ..............................................
10A2
Battery cover .......................................
31 B430
To order replacement
parts call...
1-800-4-MY-HOME ° (1-800-469-4663)
© 2003, Sears, Roebuck
and Co./®
Registered
Trademark / 7M Trademark / sty, S ervice Mark of Sears, Roebuck and Co.
114A2!11C
® Marca Registrada / TMMarca de Fabrica / s'_Marca de Servicio de Sears, Roebuck
and Co
Printed
in Mexico
Hide quick links:
Advertisement
