FujiFilm FINEPIX A310 Owner's Manual page 26

5O
• SET-UP Menu Options
IMAGE DISP. ON/OFF
POWER SAVE
FORMAT
-I_, BEEP
DATE/TIME
I_ILCD
FRAME NO. CONT./RENEW
USB MODE 1]_/1_1 PC
_;_/ENGLISH/
_/LANG, :RANCAIS/DEUTSCH/
ESPANOUq_
VIDE() SYSTEM NTSCiPAL
DISCHARGE OK
I_1RESET OK
ON/OFF
OK
LOW/HIGH/OFF
SET
ON/OFF
!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!E _!_i _!_i_ _ilii _i_i'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' ii'ii' i.....
This option specifies whether or not an image checking screen
ON (photography results) is displayed after you take a shot.
The photographed image is displayed for a few moments and
then automatically recorded.
This option allows you to specify whether the LCD monitor
ON switches off to conserve power if the camera is not used for 30
seconds. See P.51 for details.
Erases all files. See P.52 for details.
Sets the volume of the tone emitted when the camera controls
LOW
are used.
Use this option to correct the date or time. See P. 15 for details.
Use this option to specify whether the LCD monitor is
ON automatically switched ON or OFF when the Mode dial is set to
"I_1".
CONT.
ENGLISH
Specifies whether frame numbers are assigned consecutively
from previous numbers or begin again. See P.52 for details.
Selects the function when the camera is connected to a PC.
See P.62 for details.
Select English, French or German as the language used for
screen display.
Specifies whether video output is set to NTSC or PAL.
Discharges rechargeable batteries. See P.11 for details.
Resets all the camera settings other than the date and time,
frame number, language and video output setthlgs to the factory
default values set at shipment. Pressing "lb," displays a
confirmation screen. To reset the settings, press the "MENU/OK"
button.
|SE]II[,.,I I #[_11i: I=!.,1 =11 i ll _11.,'[_11=1 =1#
(!)Press the "MENU/OK" button to display the
menu screen.
@)Press "4" or "_'" to select "_1" OPTION and
then press "&" or "V" to select "SET-UP".
_Press the "MENU/OK" button to display the
SET-UP screen.
_O Press "&" or "V" to select a menu option and
then press "4" or "1_" to change the setting.
Press "_'" for "FORMAT", "DATE/TIME" or
"1_1RESET".
_}After you have modified the settings, press the
"MENU/OK" button to confirm the changes.
Always switch the camera off when replacing the batteries. If
you open the battery cover or disconnect the AC power
adapter without switching the camera off, the camera settings
may revert to the factory default values set at shipment.
II "-,l*elvAvi :1/Lg:lvj =1_",] =111 i I_[_:
Power consumption is kept to a minimum to
prevent battery depletion. You should select the
"ON" setting when you are using alkaline batteries.
_The POWER SAVE setting is disabled during automatic
playback, during rechargeable battery discharging and when
a USB connection is being used.
• Power saving "ON"
Q)lf the camera is not used for approximately 30
seconds the LCD monitor switches off
temporarily to reduce power consumption (The
viewfinder lamp (green) flashes at 1-second
intervals).
Pressing the shutter button down halfway at this
point restores the camera to the ready-to-shoot
status.
@) If the camera is left unused for 90 seconds after
the LCD monitor switches off the camera is
automatically switched off (the viewfinder lamp
switches off).
The charging time for the flash increases slightly because the
flash charging power is reduced.
If you press the shutter button down halfway and then release
it, the screen may go dark briefly because the flash is
charging.
• Power saving "OFF"
Batteries are more likely to run fiat since no power
reduction measures (sleep mode, etc.) are used.
However, this function automatically switches the
camera off if the camera is not used for
approximately 2 minutes.
.... @ When the camera has switched off @
You can switch the camera back on by briefly
switching the camera off _P and then switching it
back on again (2_.
51