Service Air Cleaner; Servicespark Plug - Craftsman 580.752211 Operator's Manual

ChangingEngine Oil
If you are using your pressure washer under extremely dirty
or dusty conditions, or in extremely hot weather, change oil
more often.
A CAUTION: Avoid prolonged or repeatedskin contact
with used motor oil.
• Usedmotoroil hasbeenshownto causeskin cancerin certain
laboratory animals.
• Thoroughly washexposed areaswith soapandwater.
KEEPOUT OFREACHOFCHILDREN.DON'T
POLLUTE.CONSERVE RESOURCES. RETURN
USEDOIL TO COLLECTION CENTERS.
Changeoil while engine is stiff warm from running, as
follows:
1. Drain fuel tank by running pressure washer until fuel
tank is empty.
2. Disconnect spark plug wire and keep it away from spark
plug.
3. Cleanarea around oil fill, remove oil fill cap/dipstick.
Wipe dipstick clean.
4. Tip your pressure washer to drain oil from oil fill into a
suitable container making sure you tip your unit away
from spark plug. When crankcase is empty, return
pressure washer to upright position.
5. Slowly pour recommended oil (about 20 oz.) into oil fill
opening. Pauseto permit oil to settle. Fill to "Full" mark
on dipstick.
6. Wipe dipstick clean each time oil level is checked. DO
NOT overfill.
7. Replace and tighten dipstick.
8. Wipe up any remaining oil.
9. Reconnect spark plug wire to spark plug.
Service Air Cleaner
Your engine will not run properly and may be damaged if you
run it with a dirty air cleaner. Service more often if operating
under dirty or dusty conditions. Replacementsare available
at your local Sears service center.
To service the air cleaner,followthese steps:
1. Loosen two screws (A) and lift off cover (B).
2. Carefully remove air cleaner (C) from base (D).
3. install clean (or new) air cleaner in base. Air cleaner
must fit securely in base.
4. Placecover over air cleaner and tighten screws.
NOTE:You can purchase new air filter elements by calling
1-800-4-1VlY-NOIVlE (469-4663).
ServiceSpark Plug
Changingthe spark plug will help your engine to start easier
and run better.
1. Cleanarea around spark plug.
2. Removeand inspect spark plug.
3. Replacespark plug if electrodes are pitted, burned or
porcelain is cracked. Use the recommended replacement
plug. See Specifications.
4. Checkelectrode gap with wire feeler gauge and reset
spark plug gap to recommended gap if necessary (see
Specifications).
_-_ f .......... __
5. install spark plug and tighten firmly.
NOTE:You can purchase a new spark plug by calling
1-800-4-1VlY-NOIVlE (469-4663).
inspect Muffler and Spark Arrestor
inspect the muffler for cracks, corrosion, or other damage.
Removethe spark arrester, if equipped, and inspect for
damageor carbon blockage.If replacementparts are required,
make sure to use only original equipement replacementparts.
NOTE:if you need to order a spark attester, please call
1-800-4-1VlY-NOIVlE (469-4663).
A WARNING: Contact with muffler area can result in
serious burns.
_ Exhaust heat/gases can ignite
combustibles, structures or damage
fuel tank causing a fire.
• DO NOTtouch hot parts and AVOID hot exhaust gases.
• Allow equipment to cool before touching.
• Keep at least 5 feet (152 cm) of clearanceon all sides of
pressure washer including overhead.
• it is a violation of California Public ResourceCode, Section
4442, to use or operate the engine on any forest-covered,
brush-covered, or grass-covered land unless the exhaust
system is equipped with a spark arrester, as defined in Section
4442, maintained in effective working order. Other states or
federal jurisdictions may havesimilar laws.
Contact the original equipment manufacturer, retailer, or dealer
to obtain a spark arrester designed for the exhaust system
installed on this engine.
• Replacement parts must be the same and installed in the same
position as the original parts.
2O