Checkout guide ....FRU ....65 System supporting the Lenovo ThinkVantage Before servicing ThinkPad T410 and T410i Toolbox program and the PC-Doctor for DOS models.
Electrical safety Observe the following rules when working on electrical equipment. Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges.
– Use caution; do not become a victim yourself. – Switch off power. – Send another person to get medical aid. Safety inspection guide The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service technicians from injury.
2. Make sure that the ESD protective devices you use have been certified (ISO 9000) as fully effective. When handling ESD-sensitive parts: • Keep the parts in protective packages until they are inserted into the product. • Avoid contact with other people. •...
Laser compliance statement (multilingual translations) The laser compliance statements in this section are provided in the following languages: • English • Arabic • Brazilian Portuguese • French • German • Hebrew • Japanese • Korean • Spanish • Traditional Chinese Chapter 1 Safety information...
– “FRU identification for CTO, CMV, and GAV products” on page 25 Important: • Advise customers to contact the Lenovo Customer Support Center if they need any assistance in obtaining or installing any software fixes, drivers, and BIOS downloads. Telephone numbers for Lenovo Support are available at: http://www.lenovo.com/support/phone...
Strategy for replacing a hard disk drive Always try to run a low-level format before replacing a hard disk drive. This will cause all customer data on the hard disk to be lost. Be sure that the customer has a current backup of the data before doing this task. Attention: The drive startup sequence in the computer you are servicing may have been changed.
Dynamic Configure To Order (CTO) This provides the ability for a customer to configure a Lenovo solution from an eSite, and have this configuration sent to fulfillment, where it is built and shipped directly to the customer. The machine label, Product Entitlement Warehouse (PEW), eSupport, and the HMM will load these products as the 4-digit MT and 3-digit model, where model = “CTO”...
Page 32
• eSupport can be used to view the list of key commodities built in a particular machine serial (this is the same record found in PEW). • eSupport can be accessed at the following Web site: http://www.lenovo.com/support. To view the key commodities, do the following: 1. Click Warranty. 2. Click Check Warranty Status.
“What to do first” on page 27 • “Checkout guide” on page 28 – “System supporting the Lenovo ThinkVantage Toolbox program and the PC-Doctor for DOS diagnostics program” on page 28 – “System supporting the Lenovo diagnostics programs” on page 34 •...
System supporting the Lenovo ThinkVantage Toolbox program and the PC-Doctor for DOS diagnostics program ® The section provides information about ThinkPad computers that support the Lenovo ThinkVantage ® Toolbox program and the PC-Doctor for DOS diagnostics program. Some descriptions might not apply to your particular computer.
Page 35
Configuration utility for DOS. The utility is available on the following Web site: http://www.lenovo.com/support PC-Doctor cannot be used to test a device that is in the docking station, even if the computer supports the docking station.
Page 36
Diagnostics Interactive Tests Hardware Info Utility Quit F1=Help Run Normal Test Run Quick Test CPU/Coprocessor Systemboard Video Adapter Fixed Disks Diskette Drives Other Devices Communication Wireless LAN Advanced Memory Tests PC-DOCTOR 2.0 Copyright 2008 PC-Doctor, Inc. All Rights Reserved. Use the cursor keys and ESC to move in menus. Press ENTER to select. The options on the test menu are as follows: Diagnostics Interactive Tests...
• The latest Lenovo ThinkVantage Toolbox is available at the following Web site: http://www.lenovo.com/support • To install the latest Lenovo ThinkVantage Toolbox on the computer, follow the instructions on the Web site. To run this program, do as follows: Windows 7: While the Windows operating system is running, press the ThinkVantage button.
Page 38
PC-Doctor for Rescue and Recovery ® In some models of ThinkPad Notebook, the Rescue and Recovery workspace enables you to run the PC-Doctor program to test the hardware features of the computer. To run the test, click “Run Diagnostics” on the Rescue and Recovery main screen. Hardware Maintenance Manual...
FRU tests The following table shows the test for each FRU. Table 1. FRU tests Applicable test System board 1. Diagnostics ➙ CPU/Coprocessor 2. Diagnostics ➙ Systemboard 3. If the docking station or the port replicator is attached to the ThinkPad Notebook, detach it.
It also can be downloaded from http://www.lenovo.com/diags. To run the Lenovo Solution Center program, click Start ➙ Control Panel ➙ System and Security ➙ Lenovo - System Health and Diagnostics, and then follow the instructions on the screen.
F12 key. 3. Press the Tab key to switch to the Application Menu window. 4. Use the arrow keys to select Lenovo Diagnostics and then press Enter. The main screen of the UEFI diagnostic program is displayed.
• If you have created the bootable diagnostic medium on a USB device, do the following: 1. Attach the USB device to the computer. 2. Turn on the computer. If the computer cannot be turned on, go to “Power system checkout” on page 36, and check the power sources.
2. Measure the output voltage at the plug of the AC adapter cable. See the following figure: Voltage (V dc) Ground (20V) Note: Output voltage of pin no.2 of the AC adapter may different from the one you are servicing. 3.
Terminal Voltage (V dc) + 0 to + 16.8 Ground (-) 7(-) 6(-) 2(+) 1(+) 3. If the voltage is less than +11.0 V dc, the battery pack has been discharged. Note: Recharging will take at least 3 hours, even if the indicator does not turn on. If the voltage is still less than +11.0 V dc after recharging, replace the battery.
Service Web site: When the latest maintenance diskette and the system program service diskette become available, they will be posted on http://www.lenovo.com/support . Restoring the factory contents by using Recovery Disc Set When the hard disk drive (HDD) or solid state drive (SSD) is replaced because of a failure, no product recovery program is on the new drive.
Attention: If the user HDP has been forgotten, check whether a master HDP has been set. If it has, it can be used for access to the hard disk drive. If no master HDP is available, neither Lenovo nor Lenovo authorized...
Attention: If User only mode is selected and the user HDP has been forgotten and cannot be made available to the service technician, neither Lenovo nor Lenovo authorized service technicians provide any services to reset the user HDPs or to recover data from the hard disk drive. The hard disk drive can be replaced for a scheduled fee.
2. When the ThinkPad logo comes up, immediately press F1 to enter BIOS Setup Utility.For models supporting the Passphrase function, press F1 while HDP icon is appearing on the screen; then enter the master HDP. For the other models, enter the master HDP. Note: To check whether the ThinkPad Notebook you are servicing supports the Passphrase function, enter the BIOS Setup Utility and go to Security ➙...
Note: Even if you do not set the low-battery alarm, the charge indicator notifies you when the battery is low, and then the computer enters the power-saving mode automatically. To cause the computer to return from sleep (standby) mode and resume operation, do one of the following: •...
• “Undetermined problems” on page 52 The symptom-to-FRU index in this section lists symptoms and errors and their possible causes. The most likely cause is listed first, in boldface type. Note: Do the FRU replacement or other actions in the sequence shown in the column headed “FRU or action, in sequence.”...
Page 51
Table 2. Numeric error codes (continued) FRU or action, in sequence Symptom or error 0192 System board. System Security— Embedded Security hardware tamper detected. 0193 Enter the supervisor password. RF antenna has been removed 0194 Enter the supervisor password. The computer has been carried through a security gate 0195 1.
Page 52
Table 2. Numeric error codes (continued) FRU or action, in sequence Symptom or error 0232 1. DIMM. Extended RAM error— Extended RAM fails at offset nnnn. 2. System board. 0250 1. Charge the backup battery for more than 8 hours System battery error—System battery is dead.
Page 53
ESC. If in the primary drive bay the customer is using a supported Lenovo HDD with an old firmware, the customer needs to update its firmware to the latest. The latest version is available at http://www.lenovo.com/support...
Table 2. Numeric error codes (continued) FRU or action, in sequence Symptom or error 201x Inform the following information to the customer: If the The solid state drive you have installed has not passed customer is using a non qualified SSD which is not qualification for use in this computer.
Page 55
Table 3. Error messages (continued) FRU or action, in sequence Symptom or error Thermal sensing error. System board. Cannot boot from any device. Check the status of device which you want to boot from. Device not found. 1. The device you want to boot from. 2.
If the LCD you are servicing has two or less visible defective pixels, it should not be considered faulty. However, if the LCD has three or more visible defective pixels, it will be deemed as defective by Lenovo and it should be replaced.
Page 57
• Lenovo will not provide replacement if the LCD is within specification as we cannot guarantee that any replacement LCD will have zero pixel defects. • One pixel consists of R, G, B sub-pixels. Table 6. LCD-related symptoms Symptom or error...
Intermittent problems Intermittent system hang problems can be due to a variety of causes that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a problem recurs. When analyzing an intermittent problem, do the following: 1.
Page 60
Table 7. Status indicators Indicator Meaning Speaker mute Orange: The speaker is on mute. To set the speakers on mute or unmute, press the speaker mute button. Microphone mute Orange: The microphone is on mute. None of the recording devices is available while the microphone mute is on by default.
Page 61
Table 7. Status indicators (continued) Indicator Meaning Device access Green: Data is being read from or written to the hard disk drive, the diskette drive, or the drive in the Serial Ultrabay Slim device. When this indicator is on, do not put the computer into sleep (standby) mode or turn off the computer.
Page 62
Table 7. Status indicators (continued) Indicator Meaning Note: If the computer is operating on battery power, the battery status indicator does not work while the computer is turned off or is in sleep (standby) mode or hibernation mode. Quick blinking orange: An error has been occurred in the battery.
Page 64
Table 8. Fn key combinations (continued) Key combination Description • External monitor only Note: To switch between the computer display and an external monitor, the Win+P key combination is also available. For Windows Vista and Windows XP: Switch between the computer display and an external monitor. If an external monitor is attached, computer output is displayed in the following three patterns by turns: •...
Page 65
Table 8. Fn key combinations (continued) Key combination Description Fn+Spacebar Enable the FullScreen Magnifier function. Fn+PrtSc Have the same function as the SysRq key. Fn+ScrLk Enable or disable the numeric keypad. The indicator of numeric lock will be displayed on the screen.
CRU; and (2) you may be charged for the replacement CRU if Lenovo does not receive the defective part within thirty (30) days of your receipt of the replacement CRU. See your Lenovo Limited Warranty documentation for full details.
Page 68
• Torque driver If you have a torque driver, refer to the Torque column in the screw information table for each step. • Make sure that you use the correct screw. It is recommended to use new screws for replacements. •...
If you replace the system board, you must restore the serial number of the system unit to its original value. Before replacing the system board, save the original serial number by doing the following: 1. Install the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later, and restart the computer.
When you replace the system board, you must set the UUID on the new system board as follows: 1. Install the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later, and restart the computer. 2. From the main menu, select 4. Assign UUID. A new UUID is created and written. If a valid UUID already exists, it is not overwritten.
CRU; and (2) you may be charged for the replacement CRU if Lenovo does not receive the defective part within thirty (30) days of your receipt of the replacement CRU. See your Lenovo Limited Warranty documentation for full details.
The Lenovo ThinkVantage Toolbox, Lenovo System Toolbox (in Windows Vista and Windows XP), and Lenovo Solution Center (in Windows 7) have an automatic battery diagnostic that determines if the battery pack is defective. A battery pack FRU should not be replaced unless this diagnostic shows that the battery is defective.
When installing: Install the battery pack in the slot. Make sure that the battery latch is in the locked position. 1020 ExpressCard blank bezel Removal steps of ExpressCard blank bezel When you press the ExpressCard blank bezel , it pops out Chapter 8 Removing and replacing a FRU...
When installing: Make sure that the bezel is correctly oriented as shown in the following figure. 1030 Serial Ultrabay Slim device or travel bezel For access, remove this FRU: • “1010 Battery pack” on page 66 Removal steps of Serial Ultrabay Slim device or travel bezel Holding the bay lock latch in the unlocked position , slide the bay eject in the direction shown by arrow , and then pull out the Ultrabay Slim device or the travel bezel in the direction shown by arrow...
1040 Hard disk drive (HDD) and solid state drive (SSD) For access, remove this FRU: • “1010 Battery pack” on page 66 Attention: • Do not drop the drive or apply any physical shock to it. The drive is sensitive to physical shock. Improper handling can cause damage and permanent loss of data.
Step Screw (quantity) Color Torque Black 0.392 Nm M3 × 3 mm, wafer-head, nylon-coated (1) (4.0 kgfcm) For HDD and HDD rubber rails: For SSD and storage converter: When installing: Make sure that the SSD or HDD is attached firmly. 1050 DIMM slot cover For access, remove this FRU: •...
1060 DIMM (in the slot on the underside of the computer) For access, remove these FRUs in order: • “1010 Battery pack” on page 66 • “1050 DIMM slot cover” on page 70 Note: Your computer has two DIMM slots: one under the keyboard and another on the underside of the computer.
Removal steps of DIMM (in the slot on the underside of the computer) When installing: Insert the notched end of the DIMM into the socket. Press the DIMM firmly, and pivot it until it snaps into place. Make sure that it is firmly installed in the slot and does not move easily. 1070 PCI Express Mini Card for wireless WAN For access, remove these FRUs in order: •...
Page 79
Removal steps of PCI Express Mini Card for wireless WAN In step , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in the direction of the arrow. Step Screw (quantity) Color...
When installing: Plug the red cable into the jack labeled MAIN, and the blue cable into the jack labeled AUX on the card. If the computer you are servicing is a wireless WAN-ready model and does not have a wireless WAN card, route the antenna cables and secure them with a tape as shown in the following figure.
Page 81
Slightly press the keyboard and slide it a little bit forward, in the direction shown by arrow , to detach the front edge of the keyboard from the frame. Lift the keyboard a little in the direction shown by arrow , and then detach the connector Chapter 8 Removing and replacing a FRU...
Page 82
Installation steps of keyboard When installing the keyboard, do as follows: 1. Attach the keyboard connector. Hardware Maintenance Manual...
Page 83
2. Attach the keyboard so that the keyboard edge is under the frame as shown in the following figure. 3. Gently press the keys with your palms and slightly slide the keyboard toward you until it snaps into position. Chapter 8 Removing and replacing a FRU...
4. Make sure that the front edge of the keyboard is attached firmly. 5. Secure the keyboard by tightening the screws from the bottom side of the computer. 1090 DIMM (in the slot under the keyboard) For access, remove these FRUs in order: •...
Page 85
Removal steps of DIMM (in the slot under the keyboard) When installing: Insert the notched end of the DIMM into the socket. Press the DIMM firmly, and pivot it until it snaps into place. Make sure that it is firmly fixed in the slot and does not move easily. Chapter 8 Removing and replacing a FRU...
1100 Backup battery For access, remove these FRUs in order: • “1010 Battery pack” on page 66 • “1050 DIMM slot cover” on page 70 • “1080 Keyboard” on page 74 Removal steps of backup battery DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode.
Cable routing: Attach the backup battery and route the cable as shown in the following figure and make sure that the battery connector is attached firmly. 1110 PCI Express Mini Card for wireless LAN For access, remove these FRUs in order: •...
Page 88
Removal steps of PCI Express Mini Card for wireless LAN In step , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in the direction of the arrow. Note: Some models might have only two antenna cables.
When installing: • In models with a wireless LAN card that has two antenna connectors, plug the gray cable into the jack marked MAIN or M, and the black cable into the jack marked AUX or A on the card. If the computer you are servicing has three cables, put the white cable in the cable protection tube and secure it with a tape as shown in this figure.
Page 90
Removal steps of keyboard bezel assembly, FPC cable, and Bluetooth daughter card Step Screw (quantity) Color Torque M2 × 14 mm, wafer-head, nylon-coated (6) Black 0.181 Nm (1.85 kgfcm) M2 × 3 mm, wafer-head, nylon-coated (3) Black 0.181 Nm (1.85 kgfcm) Torque Step Screw (quantity)
Page 92
When installing: Make sure that the connector is attached firmly. When installing: Make sure that the connectors are attached firmly. Step Screw (quantity) Color Torque M2 × 3 mm, wafer-head, nylon-coated (1) Black 0.181 Nm (1.85 kgfcm) Hardware Maintenance Manual...
When installing: Make sure that the connector is attached firmly. 1130 SmartCard or Contactless SmartCard For access, remove these FRUs in order: • “1010 Battery pack” on page 66 • “1050 DIMM slot cover” on page 70 • “1080 Keyboard” on page 74 •...
When installing: Make sure that the connector is attached firmly. Removal steps of SmartCard dummy spacer Some models have SmartCard dummy spacer as a miscellaneous part. For those models, remove the spacer as shown: Torque Step Screw (quantity) Color M2 × 3 mm, wafer-head, nylon-coated (4) Black 0.181 Nm (1.85 kgfcm)
When installing: Attach the speaker assembly and route the cable as shown in the following figure, and make sure that the speaker connector is attached firmly. 1160 LCD unit For access, remove these FRUs in order: • “1010 Battery pack” on page 66 •...
Page 98
Torque Step Screw (quantity) Color M2 × 3 mm, wafer-head, nylon-coated (1) Black 0.181 Nm (1.85 kgfcm) Black 0.181 Nm M2 × 3 mm, wafer-head, nylon-coated (1) (1.85 kgfcm) Hardware Maintenance Manual...
Page 99
Torque Step Screw (quantity) Color M2.5 × 6 mm, wafer-head, nylon-coated (2) Black 0.392 Nm (4.0 kgfcm) When installing: • Make sure that you attach the connectors firmly. • Make sure that you attach route the cables correctly and you tape up the cables in the proper positions as shown in the following figure.
Page 100
• When you route the cables, make sure that they are not subjected to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken. Hardware Maintenance Manual...
1170 Fan assembly For access, remove these FRUs in order: • “1010 Battery pack” on page 66 • “1020 ExpressCard blank bezel” on page 67 • “1050 DIMM slot cover” on page 70 • “1070 PCI Express Mini Card for wireless WAN” on page 72 •...
Page 102
Removal steps of fan assembly Step Screw (quantity) Color Torque Black 0.181 Nm M2 × 3 mm, wafer-head, nylon-coated (2) (1.85 kgfcm) M2 × 10 mm, wafer-head, nylon-coated (4) Black 0.181 Nm (1.85 kgfcm) Hardware Maintenance Manual...
Page 103
When installing: • Before you attach the fan assembly to the computer, apply thermal grease, at an amount of 0.2 grams, on the parts marked as in the following figures. Either too much or too less application of grease can cause a thermal problem due to imperfect contact with a component.
• When attaching the fan assembly to the frame, take care not to damage the heat sink of the fan assembly. • Make sure that the fan connector is attached firmly. 1180 CPU For access, remove these FRUs in order: •...
Removal steps of CPU Rotate the head of the screw in the direction shown by arrow to release the lock, then remove the CPU When installing: Place the CPU on the CPU socket, and then rotate the head of the screw in the direction shown by arrow to secure the CPU.
Page 106
Removal steps of base cover assembly, I/O sub card with USB connector and 1394 connector, and I/O sub card cable Step Screw (quantity) Color Torque M2 × 5 mm, wafer-head, nylon-coated (4) Black 0.181 Nm (1.85 kgfcm) M2 × 10 mm, wafer-head, nylon-coated (1) Black 0.181 Nm (1.85 kgfcm)
Page 107
When installing: Make sure that the wireless switch is adjusted as shown in callout Chapter 8 Removing and replacing a FRU...
Page 109
When installing: Make sure that connectors are firmly attached and route the cables as shown in the following figure. Note: Applying labels to the base cover The new base cover FRU is shipped with a kit containing labels of several kinds. Note: If the Windows Authentication label (COA) is attached to a part that is replaced, return the old part with the label attached to the customer, or provide a letter to the customer stating what the label was...
Israel label (63.5 mm x 19 mm) Anatel wireless WAN label (only for Brazil) Vodafone label Modem AMOM label (only for Brazil) FCC label Information label Serial number label Asset tag For some models, you need to apply two FCC labels. Check the old base cover; if it has two FCC labels, apply both to the new base cover.
Page 111
• “1180 CPU” on page 98 • “1190 Base cover assembly, I/O sub card with USB connector and 1394 connector, and I/O sub card cable” on page 99 Removal steps of magnesium structure frame Step Screw (quantity) Color Torque M2 × 10 mm, wafer-head, nylon-coated (2) Black 0.181 Nm (1.85 kgfcm)
1210 System board, DC-in connector cable, and ExpressCard slot assembly For access, remove these FRUs in order: • “1010 Battery pack” on page 66 • “1020 ExpressCard blank bezel” on page 67 • “1030 Serial Ultrabay Slim device or travel bezel” on page 68 •...
Page 113
Platform Controller Hub (PCH) Graphic Processing Unit (GPU) (Discrete graphics chip) Note: The GPU is only for models with the switchable graphics. Models with integrated graphics do not have a GPU on the system board. For Switchable Graphics models: For Integrated Graphics models: Chapter 8 Removing and replacing a FRU...
Step Screw (quantity) Color Torque Black 0.181 Nm M2 × 10 mm, wafer-head, nylon-coated (2) (1.85 kgfcm) M2 × 5 mm, wafer-head, nylon-coated (1) Black 0.181 Nm (1.85 kgfcm) When installing: Make sure that the connector is attached firmly. 2010 LCD bezel assembly For access, remove this FRU: •...
2020 LED board For access, remove these FRUs in order: • “1010 Battery pack” on page 66 • “2010 LCD bezel assembly” on page 108 Chapter 8 Removing and replacing a FRU...
Removal steps of LED board Torque Step Screw (quantity) Color M2 × 3.5 mm, flat-head, nylon-coated (2) Silver 0.181 Nm (1.85 kgfcm) When installing: Make sure that the connector is attached firmly. 2030 Integrated camera For access, remove these FRUs in order: •...
Removal steps of integrated camera Step Screw (quantity) Color Torque 0.181 Nm M2 × 3.5 mm, flat-head, nylon-coated (1) Silver (1.85 kgfcm) When installing: Make sure that the connector is attached firmly. 2040 LCD panel and LCD cable For access, remove these FRUs in order: •...
Page 118
Removal steps of LCD panel and LCD cable Step Screw (quantity) Color Torque Black 0.392 Nm M2.5 × 6 mm, wafer-head, nylon-coated (2) (4.0 kgfcm) Hardware Maintenance Manual...
Step Screw (quantity) Color Torque Black 0.181 Nm M2 × 3 mm, wafer-head, nylon-coated (4) (1.85 kgfcm) When installing: When attaching the LCD panel to the cover, gently press the left and right edges covered with metal. Do not press the surface of the panel or apply any excessive force to the panel. When installing: Make sure that the connector is attached firmly.
Page 120
Removal steps of camera cable Cable routing: When you install the camera, route the camera cable as shown in the following figure. Hardware Maintenance Manual...
Page 121
Note: Make sure that the LED cable is pasted on the LCD rear cover and parallel with the antenna module. For models without camera: Make sure that the LED connector is installed in the proper position as shown in the following figure. Note: Tape up the camera connector as shown in the following figure and make sure that it is not placed underneath the LCD panel.
Rear view Status indicators Note: For the description of each indicator, see Chapter 5 “Status indicators” on page 53. DisplayPort Hard disk drive or solid state drive RJ-45 (Ethernet) connector External monitor connector ac power connector RJ-11 (modem) connector Hardware Maintenance Manual...
CRU, Lenovo will ship the CRU to you. CRU information and replacement instructions are shipped with your product and are available from Lenovo at any time upon request. You may find a list of CRUs in the publications that ship with your product or at http://www.lenovo.com/CRUs. You may be required to return the defective part that is replaced by the CRU.
Page 130
• FRUs marked with are available as options. Hardware Maintenance Manual...
Table 11. Parts list—Keyboard (continued) Language FRU no. Icelandic 45N2087 45N2157 45N2227 Indian English 63Y0218 63Y0220 63Y0222 Italian 45N2088 45N2158 45N2228 Japanese 45N2102 45N2172 45N2242 Kazakhstan 45N2089 45N2159 45N2229 Korean 45N2103 45N2173 45N2243 45N2074 45N2144 45N2214 Latin American Spanish Nordic 0A61953 0A61954 0A61955...
Page 158
Table 12. Parts list—Miscellaneous parts (continued) FRU no. Base miscellaneous parts: 60Y5456 • Rubber foot (front) • Rubber foot (rear) • Lower shield • Insulation sheet, system board • Insulation sheet, sub card • Slide lock, eject • Bracket, puller eject •...
Recovery discs Windows XP Professional (32 bit) DVDs Note: The Windows XP Professional recovery DVDs are available only for models with a valid Microsoft Windows XP Professional certificate of authenticity (COA) affixed to the system. Due to a Microsoft licensing limitation, if a model came with Windows XP Professional preinstalled from the factory, but has either a Windows 7 or Windows Vista COA affixed to the system, that model is eligible only for recovery DVDs that match the operating system specified on the COA.
Page 163
Windows XP Professional (64 bit) DVDs Note: The Windows XP Professional recovery DVDs are available only for models with a valid Microsoft Windows XP Professional certificate of authenticity (COA) affixed to the system. Due to a Microsoft licensing limitation, if a model came with Windows XP Professional preinstalled from the factory, but has either a Windows 7 or Windows Vista COA affixed to the system, that model is eligible only for recovery DVDs that match the operating system specified on the COA.
Page 165
Table 22. Parts list—Windows 7 Home Premium (32 bit) recovery DVDs (continued) Language 04T1527 German Hebrew 04T1528 Japanese 04T1530 Korean 04T1531 Norwegian 04T1532 Polish 04T1533 Russian 04T1535 Russian (English-enabled) 04T1534 04T2739 Serbian-Latin Simplified Chinese 04T1522 04T1536 Spanish Traditional Chinese 04T1523 04T1529 Traditional Chinese (Hong Kong S.A.R.) Turkish...
Page 166
Table 23. Parts list—Windows 7 Home Premium (64 bit) recovery DVDs (continued) Language Korean 04T1531 Norwegian 04T1532 Polish 04T1533 Russian 04T1535 Russian (English-enabled) 04T1534 Serbian-Latin 04T2739 Simplified Chinese 04T1522 04T1536 Spanish Traditional Chinese 04T1523 04T1529 Traditional Chinese (Hong Kong S.A.R.) Turkish 04T1537 Windows 7 Professional (32 bit) DVDs...
Page 167
Table 24. Parts list—Windows 7 Professional (32 bit) recovery DVDs Language Brazilian Portuguese 04T1479 Czech 04T1482 Danish 04T1506 English 04T1483 04T1484 English (for India) English (modem-disabled) 04T1505 04T1508 English, Finnish, and Swedish (in Sweden) English, French, German, and Dutch (in Belgium and Luxemburg) 04T1507 04T1509 English, French, German, and Italian (in Switzerland)
USB floppy diskette drive for maintenance diskette USB floppy diskette drive tool kit 27L3452 42W7820 Test card for integrated Smart Card — LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later Note: Download the file from the following Web site: http://www.lenovo.com/support Chapter 10 Parts list...
Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any Lenovo intellectual property right may be used instead.
Trademarks The following terms are trademarks of Lenovo in the United States, other countries or both: Active Protection System Lenovo Rescue and Recovery ThinkLight ThinkPad ThinkVantage TrackPoint Ultrabay UltraNav The following terms are trademarks of the Microsoft group of companies:...
Page 174
Part Number: 63Y0535_05 Printed in (1P) P/N: 63Y0535_05 *63Y0535_05*...