Door Swing Dimensions; Tipping Radius; Anti-Tip Requirements - KitchenAid KSSC36FJB00 Installation Instructions Manual

Door swing dimensions

F
B
A
90°
110°
Freezer
door

Tipping radius

Note: Dolly wheel height must be added to tipping
radius when a dolly is used.
Size A
36" (91 cm) 87-1/4" (222 cm)
42" (106 cm) 87-1/4" (222 cm)
48" (122 cm) 87-1/4" (222 cm)
If additional ceiling clearance is required for tipping the
refrigerator, follow the directions for your model.
For wraparound metal models:
• Grasp both ends of the louver panel. Push straight up,
then pull out and remove.
• Remove the two screws attaching grille panel, slide the
grille panel down and remove.
• Remove the six screws attaching each cabinet side trim to
the refrigerator and remove the side trims.
• Reassemble after dolly has been removed from refrigerator.

Anti-tip requirements

If a solid soffit 1" (2.5 cm) max. above refrigerator is not
available, prevent the refrigerator from tipping during
use, as shown.
Securely attach a 32" (81 cm) long min. wood board(s) to
wall studs behind refrigerator. The wood screws must be
screwed into the studs 1-1/2" (3.8 cm) min. The board(s)
must overlap the compressor cover as shown.
installed before refrigerator is installed.
Locate the board(s) so the bottom surface
of the board(s) are 84" (213 cm) from the
refrigerator up so there is 1/4" (6.4 mm)
max. between top of the refrigerator and
DO NOT crush the condenser cover when
Page 4
Top front
of refrigerator
Refrigerator
door
130°
90°
110°
130°
B
90-1/2" (230 cm)
93" (236 cm)
96" (244 cm)
Board(s) must be long enough to fully
cover width of compressor cover.
It is recommended that board(s) be
floor. During installation, raise the
bottom of anti-tip board(s).
raising the rear leveling legs.
E
D
C
Forward/backward
tipping radius
A
For panel models:
• Grasp both ends of the panel. Push straight
up, then pull out and remove.
• Remove the four screws attaching the frame
to the brackets and remove.
• Remove two screws attaching each bracket
to the refrigerator and remove
• Reassemble after dolly has been removed from refrigerator.
1/4" (6.4 mm)
max.
2" (5.1 cm)
min.
rear
wall
36" 42"
91 cm 106 cm
38-1/2" 41"
A
(98 cm) (104 cm)
36-1/16" 38"
B
(92 cm) (97 cm)
43-1/2" 47"
C
(110 cm) (119 cm)
40" 42-9/16"
D
(102 cm) (108 cm)
19-3/4" 23-1/4"
E
(50 cm) (59 cm)
14-1/2" 17-1/4"
F
(37 cm) (44 cm)
Location must permit doors to open to 110°
min. Allow 4-1/2 inch (11.4 cm) min. space
between refrigerator side and corner wall.
Side
tipping radius
B
48"
122 cm
43-1/2"
(110 cm)
40"
(102 cm)
50-1/2"
(128 cm)
45-1/4"
(115 cm)
26-3/4"
(68 cm)
19-3/4"
(50 cm)
bracket
screws