Related Manuals for Zenoah G2000
Summary of Contents for Zenoah G2000
- Page 1 G2000 115 31 92-10 (001) OWNER’S MANUAL CHAIN SAW G2000 Original Language GB-1...
- Page 2 G2000 EXPLANATION OF SYMBOLS AND SAFETY WARNINGS Read operator's instruction Wear head, eye and ear book before operating this protection. machine. Use the chain saw Warning! Danger of with two hands. kickback. Use appropriate protections Read, understand and for foot-leg and hand-arm. follow all warnings.
-
Page 3: Table Of Contents
Directive 2006/42/EC on machinery and to Directive 2004/108/EC on electromagnetic compatibility and to the regulations governing transposition internal control production. Manufacturer Husqvarna Zenoah Co., Ltd. 1-9 Minamidai, Kawagoe, Saitama, Japan DECLARES THAT THE DESIGN OF THE MACHINE DESCRIBED BELOW. Description... -
Page 4: For Safe Operation
G2000 1. For safe operation WARNING This chainsaw has been especially designed for tree maintenance and should therefore only be used by trained operators when working on trees. 1. Never operate a chain saw when you are fatigued, ill, or upset, or under the influence of medication that may 10. - Page 5 G2000 20. Operate the chain saw only in well handle, and the left hand on the front ventilated areas. Never start or run handle, when the engine is running. the engine inside a closed room or Use a firm grip with thumbs and fin- building.
- Page 6 G2000 WORKING WITH TREE SERVICE CHAIN-SAWS The saw should only be attached to the recommended FROM A ROPE AND HARNESS attachment points on the harness. These may be at This chapter sets out working practices to reduce the mid-point (front or rear) or at the sides. Where possible risk of injury from tree service chainsaws when working attaching the saw to centre rear mid-point will keep it at height from a rope and harness.
- Page 7 G2000 One-hand use of the chainsaw Operators should not use tree service chainsaws one- handed in place of unstable work positioning or in pref- erence to a handsaw when cutting small diameter wood at the branch tips. Tree service chainsaws should only be used one-handed where: •...
-
Page 8: Explanation Of Symbols On The Machine
G2000 2. Explanation of Symbols on the Machine For safe operation and maintenance, symbols are carved in relief on the machine. WARNING According to these indications, please be careful not to make any mistake. The port to refuel “MIX GASOLINE” Position: Fuel cap The port to top up chain oil Position: Oil cap... -
Page 9: Installing Guide Bar And Saw Chain
G2000 3. Installing Guide Bar and Saw Chain A standard saw unit package contains the items as illustrated. Plug wrench Power unit (Hexagon socket (S13/S16) + Bar protector Slotted driver) Guide bar Saw chain Screwdriver for carburetor adjustment (Slotted driver) Open the box and install the guide bar and the saw WARNING chain on the power unit as follows:... -
Page 10: Fuel And Chain Oil
• The Zenoah engines are lubricated by oil specially spillage around the unit. formulated for air-cooled 2-cycle gasoline engine use. If Zenoah oil is not available, use an anti-oxidant added WARNING quality oil expressly labeled for air-cooled 2-cycle 1. Select bare ground for fueling. -
Page 11: Operating The Engine
G2000 5. Operating the Engine 6. When engine has ignited, first push in the choke knob WARNING to the first-stage position and then pull the starter It is very dangerous to run a chainsaw that mounts again to start the engine. broken parts or lacks any parts. -
Page 12: Sawing
G2000 1. H and L needles are restricted within the number of WARNING turn as shown below. • When the brake operates, release the throttle lever to slow down the engine speed. Continuous opera- H needle : -1/4 tion with the brake engaged will generate heat from L needle : ±... - Page 13 G2000 • This saw is equipped with a chain A log lying on the ground brake that will stop the chain in the event of kickback if operating prop- erly. You must check the chain brake operation before each usage by run- ning the saw at full the throttle for I -2 seconds and pushing the front hand guard forward.
-
Page 14: Maintenance
G2000 7. Maintenance 3. Oil filter WARNING 1. With a wire hook, take out the oil filter from the feed- Before cleaning, the inspecting or repairing the unit, ing port. make sure that engine has stopped and is cool. Dis- connect the spark plug to prevent accidental starting. -
Page 15: Maintenance Of Saw Chain And Guide Bar
After each cutter has been filed, check the depth gauge and file it to the proper level as illustrated. WARNING: This saw is equipped with one of the following low kick- back bar/chain combinations: Zenoah Part Number Bar Size Guide Bar Saw Chain Appropriate gauge checker... -
Page 16: Troubleshooting Guide
G2000 9. Troubleshooting Guide Case 1. Starting failure Case 3. Oil does not come out Check oil for sub- WARNING Replace. standard quality. Make sure the icing prevention system is not working. Check fuel for water Replace with proper Check oil passage or substandard mix- fuel. -
Page 17: Specifications
UNITS WHICH HAVE BEEN DAMAGED BY NEGLI- THE PURCHASER SHALL BEAR COSTS OF TRANS- GENCE OF INSTRUCTION LISTED IN THE OWNER/ PORTING THE UNIT TO AND FROM THE ZENOAH OPERATOR MANUAL FOR PROPER USE AND MAIN- DEALER. TENANCE OF THE UNITS ACCIDENT MISHANDLING,...