Related Manuals for Zenoah G2500
Summary of Contents for Zenoah G2500
- Page 1 G2500/G2500 OPS 115 59 93-38 (306) OWNER’S MANUAL CHAIN SAW G2500 G2500 (One-Push-Start) Original Language GB-1 01-G2500･G2500 ops_GB_306＿四.indd 1 13.7.4 5:43:49 PM...
-
Page 2: Table Of Contents
5. Throttle interlock 6. Right handle 7. Throttle lever 8. Engine switch ② ① 9. Fuel tank ⑤ ③ 10. Oil tank ⑥ 11. Left handle 12. Saw chain 13. Guide Bar ⑨ ⑩ ⑪ GB-2 01-G2500･G2500 ops_GB_306＿四.indd 2 13.7.4 5:43:50 PM... -
Page 3: Specification
Max speed: ..........12,500 (min <Hard nose bar> Idle speed: ..........2,900 (min Sprocket: ..............8T Power: ......G2500 0.96/9,000 (kw/min Chain speed at max. power: ......15.2 (m/s) G2500 ops 0.88/9,000 (kw/min Guide bar Type: ......ZENOAH carving (Hard nose) Noise at Operator’s ear (Racing): ..... -
Page 4: For Safe Operation
9. Always hold the chain saw firmly with tion. both hands when the engine is run- 19. Keep the handles dry, clean and free ning. Use a firm grip with thumb and of oil or fuel mixture. GB-4 01-G2500･G2500 ops_GB_306＿四.indd 4 13.7.4 5:43:53 PM... - Page 5 Sudden surprise semble the machine. contributes to accidents. • When you dispose of the machine, fuel, chain oil, be (2) Keep a good grip on the saw with sure to follow your local regulations. both hands, the right hand on the rear GB-5 01-G2500･G2500 ops_GB_306＿四.indd 5 13.7.4 5:43:55 PM...
- Page 6 GB-6 01-G2500･G2500 ops_GB_306＿四.indd 6 13.7.4 5:43:55 PM...
- Page 7 (toward the tips of the branch), in order to prevent the saw being taken with the section and further complicat- ing the situation. GB-7 01-G2500･G2500 ops_GB_306＿四.indd 7 13.7.4 5:43:55 PM...
-
Page 8: Explanation Of Symbols On The Machine
If you turn the rod by screwdriver follow the arrow to the “MAX” position, the chain oil flow more, and if you turn to the “MIN” position, less. Position: Bottom of the power unit <G2500 OPS> Shows the direction of the select lever for the OPS (one-push-start) and “Super e-start”. Position: Upper side of the recoil starter GB-8 01-G2500･G2500 ops_GB_306＿四.indd 8 13.7.4 5:43:55 PM... -
Page 9: Installing Guide Bar And Saw Chain
Tighten 8. Tighten the tensioner screw. WARNING A new chain will expand its length in the beginning of use. Check and readjust the tension frequently as a loose chain can easily derail or cause rapid wear of itseif and the guide bar. GB-9 01-G2500･G2500 ops_GB_306＿四.indd 9 13.7.4 5:43:55 PM... -
Page 10: Fuel And Chain Oil
3. Stop the engine before refueling the unit. At that time, be sure to sufficiently agitate the mixed gasoline in the con- tainer. • The Zenoah engines are lubricated by oil specially formu- ■ FOR YOUR ENGINE LIFE, AVOID: lated for air-cooled 2-cycle gasoline engine use. If Zenoah oil 1. -
Page 11: Operating The Engine
7. Allow the engine to warm up with the throttle lever pulled slightly. Throttle lever (G2500 OPS : OPS “one-push-start”) (G2500 OPS : “Super e-start”) • Set the select lever to the “Super e-start” mode as WARNING shown in the label, to the direction of rear side until it • Use One-push-start after performing warming-up by... - Page 12 If the engine cannot be started by the above procedure, repeat the above operations again. If the engine cannot be started smoothly, it may be necessary to add warm- ing-up or readjust the engine. Perform warming-up enough and ask the distributor to readjust the engine. GB-12 01-G2500･G2500 ops_GB_306＿四.indd 12 13.7.4 5:43:56 PM...
- Page 13 When the brake operates, a yellow cone pops up from the base of the brake lever. Releasing the Brake Pull the brake lever up toward the left-hand handle until it clicks into place. GB-13 01-G2500･G2500 ops_GB_306＿四.indd 13 13.7.4 5:43:56 PM...
-
Page 14: Sawing
I -2 seconds and pushing the front hand GB-14 01-G2500･G2500 ops_GB_306＿四.indd 14 13.7.4 5:43:57 PM... -
Page 15: Maintenance
2. Oiling port Dismount the guide bar and check the oiling port for ■ PERIODICAL SERVICE POINTS clogging. 1. Cylinder fins Reriodically check and clean the cylinder fins in the repair specialty store. Oiling port GB-15 01-G2500･G2500 ops_GB_306＿四.indd 15 13.7.4 5:43:57 PM... - Page 16 Clean the electrodes with a wire brush and reset the gap the starter of One-push-start model, the select lever to 0.6 mm as necessary. should be in the position of the rear side (G2500 One- push-start only). 5. Sprocket • Don’t pull the starter when detaching it from the unit.
-
Page 17: Maintenance Of Saw Chain And Guide Bar
This saw is equipped with one of the following low kickback bar/chain combinations: Zenoah Part Number Bar Size Guide Bar Saw Chain Appropriate gauge checker 2475-52111 580703501 (91PX) 2475-52121 3622-52210 (25AP) Make the shoulder round 0.025″ (0.64 mm) Depth gauge standard GB-17 01-G2500･G2500 ops_GB_306＿四.indd 17 13.7.4 5:43:58 PM... -
Page 18: Troubleshooting Guide
If the unit seems to need further service, please consult with an authorized service shop in your area. 13. Disposal • When you dispose of the machine, do not disas- semble the machine. • When you dispose of the machine, fuel, chain oil, be sure to follow your local regulations. GB-18 01-G2500･G2500 ops_GB_306＿四.indd 18 13.7.4 5:43:58 PM... - Page 19 SPECIFIED BY THE COMPANY, OR OTHER CAUSES BEYOND THE COMPANY'S CONTROL. THE PURCHASER SHALL BEAR COSTS OF TRANS- PORTING THE UNIT TO AND FROM THE ZENOAH THIS WARRANTY DOES NOT COVER THOSE PARTS DEALER. REPLACED BY NORMAL WEAR OR HARMLESS CHANGES IN THEIR APPEARANCE.
- Page 20 01-G2500･G2500 ops_GB_306＿四.indd 20 13.7.4 5:43:58 PM...