Trouble Shooting - One for All URC 7800 Cinema 7 User Manual

TROUBLE SHOOTING

Problem Solution
Red light does not Replace the batteries with four (4) new AAA alka-
blink when you press line batteries.
a key?
The Cinema 7+™ Try all of the codes listed for your brand of home
does not operate entertainment component in the "Setup Codes" sec-
your home entertain- tion. Many setup codes may allow for partial func-
ment components or tionality, however, only one setup code will operate
is not performing your home entertainment component correctly.
commands properly? Make sure that all of the components you are
setting up can be operated with an infrared
remote control.
Problems program- Try the VCR set-up codes for your brand. However,
ming a TV/VCR some combo units may require both a TV code for
combo? volume control and a VCR code for the remaining
functions.
VCR not recording? As a safety feature on the Cinema 7+™, you must
press the REC key twice.
CH / and PREV Due to RCA design (1983-1987), only the original
CH not working for remote control will operate these functions.
your RCA TV?
Problems changing If your original remote control required an Enter
channels? keystroke when changing channels, press the
ENTER key on the Cinema 7+™ after you enter the
channel number.
The red light blinks Make sure you are aiming your Cinema 7+™ at your
when you press a home entertainment component and that you are
key but you receive within 15 feet before using your remote.
no response from
your home
entertainment
component?
Cinema 7+™ not Make sure your remote controls are nose-to-nose
learning a command and are no more than 2 inches apart (see diagram
from your original in step 5 on page 24).
remote control?
Tried "Search Try the "Search Method" again after clearing out the
Method" and still did device key as follows: Press and hold SETUP until
not find the code? red light blinks twice, then release. Next enter 9 - 9 -
2. Then press and release the device key to be
cleared twice.
Sony's Picture In Press TV once. Press and hold SETUP until red
Picture (PIP) won't light blinks twice, then release. Enter 9 - 9 - 4 and
turn off? press SETUP once. Then enter 6 - 2 - 1 and press
PIP On/Off. The red light should blink twice. PIP
should operate properly now.
Sharp's Picture In Sharp's PIP feature requires separate PIP functions
Picture (PIP) won't for "on" and "off".
work properly?
For PIP "on", press TV once. Press and hold SETUP
until red light blinks twice, then release. Enter 9 - 9 - 4
and press SETUP once. Enter 3 - 4 - 8 and press PIP
On/Off. The red light should blink twice. PIP "on"
should operate properly now.
For PIP "off", press TV once. Press and hold
SETUP until red light blinks twice, then release.
Enter 9 - 9 - 4 and press SETUP once. Enter 6 - 0 - 6
and press SETUP PIP On/Off. The red light should
blink twice. PIP "off" should operate by pressing
SETUP then the PIP key.
Web Site : http://www.oneforall.com
30
TROUBLE SHOOTING (continued)
Problem Solution
Surround on Sony Press RCVR once. Press and hold SETUP until red
receiver will not light blinks twice, then release. Enter 9 - 9 - 4 and
turn on? press SETUP once. Enter 3 - 9 - 8 and press SUR-
ROUND. Red light should blink twice. Surround
should operate now.
Sony receiver will Try using the number pad on the Cinema 7+™ to
turn off but not turn the receiver back on. For example, try pressing
back on?
0 to turn on in the CD mode, or 4 to turn on in the
Video 1 mode. Other numeric keys will also turn the
receiver on. If this doesn't work, try the following:
Press RCVR once. Press and hold SETUP until red
light blinks twice, then release. Enter 9 - 9 - 4 and
press SETUP once. Then enter 5 - 9 - 1 and press
POWER. The red light should blink twice. Power
should operate properly now.
Audio component Audio functionality may be split between codes. For
not fully-operational? example, Pioneer's Tuner code 0014 works tuner
presets, but only Amplifier code 0013 works power
and volume. This also true for Sony's Receiver code
0158 and Misc. Audio code 0159.
If some functionality is missing, try other codes to
see if functionality resides there.
Mini-system, book- These systems may operate using a CD or Misc.
shelf, or boombox Audio code. If the original remote control did not
not working? have a power key, press PL (or STOP) to turn on
(or off) the system.
Consumer Help Line : 1-330-405-8606
E-Mail Address : HAGHelp@ueic.com
World Wide Web : http://www.oneforall.com
Web Site : http://www.oneforall.com
31