Related Manuals for Uniden UH039P
Summary of Contents for Uniden UH039P
- Page 1 UH039P Operating Guide To bring outstanding wireless communication products to people's lives throughout the world.
-
Page 2: Control & Indicators
CONTROL & INDICATORS INCLUDED IN YOUR PACKAGE: UH039P Radio (2) Operating Guide Belt Clip (2) Charging Cradle with AC Adaptor NiMH Battery Pack (2) OPTIONAL ACCESSORIES VOX Earset VOX Headset Carry Case SCAN hi/lo channel/ volume scan SCAN 1 Antenna 12 Channel Indicator 2 PTT (Push-To-Talk) Button 13 Receive Indicator... -
Page 3: Getting Started
GETTING STARTED Uniden does not represent this product to be waterproof. Do not expose this product to Rain or Moisture. BATTERY INSTALLATION Your UH039P unit uses the included NiMH battery pack for power. The unit can be powered with optional 4 AAA ALKALINE batteries. -
Page 4: Low Battery Alert
channel/ volume scan charge 1 charge 2 Power Point Place the UH039P into the charge cradle. The charge light will come on to indicate the unit is charging. Before operating the UH039P , charge the battery pack for 16 hours. Do not charge alkaline or non rechargeable batteries. -
Page 5: Operation
OPERATION POWER ON/OFF Press and hold to turn the radio on. A channel number will appear on the display. Press and hold to turn the radio off. VOLUME Press volume to increase or decrease the volume level. icon appears on the display while 'VOL' volume is being adjusted. -
Page 6: Selecting Channel
SELECTING CHANNEL Press channel/scan to select hi/lo the desired channel. channel/ volume scan TO TRANSMIT AND RECEIVE uses the 40 UHF-CB Channels. For your UH039P reference a list of the available channels and corresponding frequencies is printed on page 10. 1. - Page 7 TRANSMIT Hi/Lo SELECT Press and hold for 2 seconds when the unit is in Transmit Lo and it will switch to Transmit Hi. 'HI' icon will appear on display. Press and hold for 2 seconds again to return to Transmit Lo setting. 'HI' icon will disappear from display.
-
Page 8: To Operate In Duplex Mode (Repeaters)
TO OPERATE IN DUPLEX MODE (REPEATERS) The Duplex function enables you to access local repeater stations. You can only activate Duplex from CH01-CH08. UHF CB Repeaters are used to retransmit or relay your signal. Repeaters will extend the range of your radio and overcome the shielding effect caused by solid obstructions. - Page 9 SCANNING The scan function scans all channels and stops at an active channel. When the signal stops, the waits 2 seconds UH039P (Reply Delay) before scanning resumes. To initiate scanning, 1. Assuming the unit is on CH01 SCAN when switched on. 2.
-
Page 10: Reply Delay
REPLY DELAY While scanning, the stops at a busy channel and UH039P receives a transmission. When the received signal is over, the unit will wait for 2 seconds for the return of the signal, otherwise, the radio resumes scanning. is the automatic transmitting function by inputting voice into the optional headset mic without pressing the button. -
Page 11: Uhf Channels & Frequencies
UHF CHANNELS & FREQUENCIES Simplex Mode Duplex Mode Simplex Mode CH No. Transmit / Receive Transmit CH No. Transmit / Receive Frequency (MHz) Frequency (MHz) Frequency (MHz) 476.425 477.175 CH31 476.925 476.450 477.200 CH32 476.950 476.475 477.225 CH33 476.975 476.500 477.250 CH34 477.000 476.525... -
Page 12: Warranty
Uniden, (C) Improperly installed, (D) Repaired by someone other than an authorised Uniden Repair Agent for a defect or malfunction covered by this warranty, (E) Used in conjunction with any equipment or parts or as part of a system not...