Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Cleform Gilson 59015C
Summary of Contents for Cleform Gilson 59015C
- Page 1 GILSJ J N MIXERS 5 1/2 CU. FT. CONCRETE MIXER MODEL: 59015C OPERATOR’S GUIDE & PARTS MANUAL GILSJ J N MIXERS 4343 Easton Road · St. Joseph, MO 64503 816-233-4840 · 800-253-3676 Fax 816-233-4624 · 888-253-3676 E-Mail: cleform@ccp.com Web Address: www.cleform.com...
-
Page 2: Table Of Contents
INTRODUCTION This operator’s manual has been prepared to provide the information you need to correctly operate and maintain your unit. Read it carefully and keep it for future reference. Should you ever need repair parts or service, contact your authorized parts and service dealer. -
Page 3: Safety Precautions
1-SAFETY PRECAUTIONS THE FOLLOWING PRECAUTIONS ARE SUGGESTED TO HELP PREVENT ACCIDENTS. A CAREFUL OPERATOR IS THE BEST OPERATOR. MOST ACCIDENTS CAN BE AVOIDED BY OBSERVING CERTAIN PRECAUTIONS. READ AND TAKE THE FOLLOWING PRECAUTIONS BEFORE OPERATING THIS EQUIPMENT TO HELP PREVENT ACCIDENTS. EQUIPMENT SHOULD BE OPERATED ONLY BY THOSE WHO ARE RESPONSIBLE AND INSTRUCTED TO DO SO. -
Page 4: Operation
2-OPERATION DRUM SPEED The mixer drum should revolve between 20 and 25 R.P.M.’s for best results in mixing concrete. To obtain this speed using a 1725/1800 R.P.M. electric motor, use a 2” diameter “A” section V-pulley. If using a 6 to 1 speed reduction 3 H.P. gasoline engine, use a 6 ¼” diameter “A” section V-pulley. -
Page 5: Loading The Mixer
LOADING THE MIXER Start the mixer. Refer to motor/engine instructions. After drum has started rotating, pour about half of the water in the drum. NOTE: The drum my leak slightly when first used. This will stop after a few batches. Add aggregate (gravel) first then cement and last sand. -
Page 6: Lubrication And Storage
3-LUBRICATION & STORAGE Each day before operating, lubricate at the following points: Engine/Motor – Refer to engine/motor operating instructions for all maintenance and lubrication instructions and requirements. GREASE FITTINGS : Refer to Fig. 2 Clean off grease fitting before greasing. Use pressure type grease gun. Grease lightly with general purpose grease (2 to 3 pumps). -
Page 7: Replacement Decals
4-REPLACEMENT DECALS #217728: Decal, Safety Instructions #5706: Decal, Gilson Name Plate #38257: Decal, Drum Rotation... -
Page 9: Parts List
CONCRETE MIXER PARTS LIST ITEM NO. PART NO. DESCRIPTION QTY. 1102 Grease Fitting 1183 Grip 19866 Bearing Cap 19902 Drum Assembly 19911 Blade Assembly 19913 Paddle Assembly 19914 Drum Shaft Assembly 214858 Belt Guard Cover 214907 Belt Guard Assembly 245948 Frame Assembly 245949 Yoke Assembly 245952 Tilt Handle 245956 Bushing Spacer... - Page 10 MIXERS ONE-YEAR WARRANTY This product is warranted to the original purchaser only, to be free of defects in material and workmanship under normal use, for one year from purchase date. Cleform Tool Corp. shall without charge for parts and labor, repair or replace such parts which are found to be defective.
- Page 11 ALL IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR FROM DATE OF PURCHASE BY THE ORIGINAL RETAIL CUSTOMER AND TO THE EXTENT PERMITTED BY LAW ANY AND ALL IMPLIED WARRANTIES ARE EXCLUDED AND DISCLAIMED AFTER THE EXPIRATION OF SUCH PERIOD.