Page 1 ThinkServer TS130 Hardware Maintenance Manual Machine Types: 1098, 1100, 1105, and 1106...
Page 2 • Appendix A “Notices” on page 97 Fourth Edition (August 2012) © Copyright Lenovo 2011, 2012. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.
Page 4 Index....Lenovo Support Web site..Help and service ....
Page 5: Safety Information
제품을 사용하기 전에 제품과 함께 제공되는 문서 DVD의 다국어 안전 지침을 주의 깊게 읽어보십시오. Voordat u het product gebruikt, moet u ervoor zorgen dat u de meertalige veiligheidsinstructies op de documentatie-dvd van het product hebt gelezen en begrijpt. © Copyright Lenovo 2011, 2012...
Page 6 Ensure that you read and understand all caution and danger statements in this document before you perform the procedures. Read and understand any additional safety information that is included with the server or optional device before you install, remove, or replace the device. ThinkServer TS130 Hardware Maintenance Manual...
Page 7 Do not: • Throw or immerse into water • Heat to more than 100°C (212°F) • Repair or disassemble Dispose of the battery as required by local ordinances or regulations. © Copyright Lenovo 2011, 2012...
Page 8 The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source. ThinkServer TS130 Hardware Maintenance Manual...
Page 9 Statement 9 CAUTION: Disconnect the hot-swap fan cables before removing the fan from the device to protect against personal injury. Statement 10 CAUTION: The following label indicates a sharp-edge hazard. © Copyright Lenovo 2011, 2012...
Page 10 In addition, the device might have multiple connections to dc power. To remove all electrical current from the device, ensure that all connections to dc power are disconnected at the dc power input terminals. viii ThinkServer TS130 Hardware Maintenance Manual...
Page 11 This product contains a Class 1M laser. Do not view directly with optical instruments. Statement 18 CAUTION: Do not place any object on top of rack-mounted products. Statement 19 CAUTION: Hazardous moving parts. Keep fingers and other body parts away. © Copyright Lenovo 2011, 2012...
Page 12: Safety Inspection Guide
Statement 20 CAUTION: A lithium ion battery is provided. To avoid possible explosion, do not burn the battery. Replace the battery only with the Lenovo-approved part. Recycle or discard the battery as instructed by local regulations. Safety inspection guide The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service technicians from injury.
Page 13: Chapter 1. General Information
• For the most up-to-date information about your server, go to: http://www.lenovo.com/thinkserver • Lenovo maintains pages on the World Wide Web, where you can get the latest technical information and download documentation or device drivers and updates. To access the Lenovo Support Web site, go to: http://www.lenovo.com/support...
Page 14 DVD. Note: Lenovo maintains pages on the World Wide Web, where you can get the latest technical information and download documentation or device drivers and updates. Some information in the documents on the documentation DVD might change without notice after the first release of the DVD.
Page 15 This document provides information about component locations, replacement procedures for major Field Replaceable Units (FRUs), and troubleshooting and diagnostics. This document is updated frequently, and the most up-to-date version is always available in English on the Lenovo Web site at: http://www.lenovo.com/ThinkServerUserGuides...
Page 16 ThinkServer TS130 Hardware Maintenance Manual...
Page 17: Chapter 2. Server Setup Road Map
See the operating system help. This step is not required if the operating system was in the operating system installed using the ThinkServer EasyStartup program. Install applications Refer to the documentation that comes with the applications that you want to install. © Copyright Lenovo 2011, 2012...
Page 18 ThinkServer TS130 Hardware Maintenance Manual...
Page 20 • Two optical drive bays • Microsoft Windows Small Business Server 2011 • Two hard disk drive bays Essentials/Standard • Two PCI card slots • Microsoft Windows Multipoint Server 2011 • One PCI Express x1 card slot ThinkServer TS130 Hardware Maintenance Manual...
Page 21 Table 2. Features and specifications (continued) • One PCI Express x16 card slot • Red Hat Enterprise Linux 6.2 (32-bit and 64-bit) Integrated functions: Environment • Ethernet controllers (The server comes with two • Air temperature: integrated Gigabit Ethernet controllers, which support connection to 100 Mbps or 1000 Mbps network.) Operating: 10°C to 35°C (50°F to 95°F) •...
Page 22: Software
77. BIOS update utilities The BIOS firmware keeps updating after the shipment of the server. Lenovo maintains pages on the Support Web site and provides the BIOS update utilities with instructions for download to help you update the BIOS firmware if needed.
Page 23: Chapter 4. Locating Parts, Controls, And Connectors
This topic helps you locate the label that contains the machine type, model, and serial number information for your server. When you contact Lenovo for help, the machine type, model, and serial number information helps support technicians to identify your server and provide faster service.
Page 24: Rear View
Figure 4 “Rear connector locations” on page 13 shows the locations of the connectors on the rear of your server. Some connectors on the rear of your server are color-coded to help you determine where to connect the cables in your server. ThinkServer TS130 Hardware Maintenance Manual...
Page 25 Figure 4. Rear connector locations Power cord connector Microphone connector Audio line-out connector Serial port VGA monitor connector Audio line-in connector DisplayPort connector PCI Express x16 card slot bracket USB connectors (6) PCI Express x1 card slot bracket Ethernet connector PCI card slot brackets (2) Connector Description...
Page 26: Locating Parts On The System Board
Front audio connector (for connecting the microphone and headphone connectors on the front bezel) Thermal sensor connector PCI card slots (2) 24-pin power connector PCI Express x1 card slot Battery PCI Express x16 card slot ThinkServer TS130 Hardware Maintenance Manual...
Page 27: Internal Components
SATA connectors 1 and 2 (SATA 3.0 Rear fan connector connectors) SATA connector 3 (SATA 2.0 connector) Cover presence switch connector (Intrusion switch connector) Microprocessor eSATA connector Front fan connector PS/2 keyboard and mouse connector Internal components Figure 6 “Component locations” on page 15 shows the locations of the various components in your server. To remove the server cover and access the inside of the server, see “Removing the server cover”...
Page 28: Internal Drives
To remove the server cover and gain access to the inside of the server, see “Removing the server cover” on page 21. For the system board components, see “Locating parts on the system board” on page 14. ThinkServer TS130 Hardware Maintenance Manual...
Page 29 FRU information, such as FRU part numbers and supported server models, go to: http:/www.lenovo.com/serviceparts-lookup Notes: • Before servicing a Lenovo product, ensure that you read and understand “Safety information” on page iii. • Use only parts provided by Lenovo. Chapter 4...
Page 30 Card reader (available in some models) Hard disk drive Heat sink and fan assembly Keyboard Memory module Mouse Optical drive PCI card (available in some models) Power supply assembly Rear fan assembly System board battery System board ThinkServer TS130 Hardware Maintenance Manual...
Page 31: Chapter 5. Installing, Removing, Or Replacing Hardware
• Before using the product, be sure to read and understand the multilingual safety instructions and the Lenovo Limited Warranty (LLW) on the documentation DVD that comes with the product. Reading and understanding the safety instructions reduces the risk of personal injury and damage to your product.
Page 32: Handling Static-Sensitive Devices
• The use of a grounding system is recommended. For example, it is recommended to wear an electrostatic discharge (ESD) wrist strap, if one is available. Ensure that you work in an ESD-safe area. Select a grounding system, such as those listed below, to provide protection that meets the specific service requirement. ThinkServer TS130 Hardware Maintenance Manual...
Page 33: System Reliability Guidelines
Note: The use of a grounding system to guard against ESD damage is desirable but not necessary. – Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground. – When working on a double-insulated or battery-operated system, use an ESD common ground or reference point.
Page 34: Removing And Reinstalling The Front Bezel
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information” on page iii and “Guidelines” on page 19. This section provides instructions on how to remove and reinstall the front bezel. To remove and reinstall the front bezel, do the following: ThinkServer TS130 Hardware Maintenance Manual...
Page 35 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. Remove the server cover. See “Removing the server cover” on page 21. 3.
Page 36: Installing, Removing, Or Replacing Optional Hardware Devices
To install or replace a PCI card, do the following: 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. ThinkServer TS130 Hardware Maintenance Manual...
Page 37 2. Remove the server cover. See “Removing the server cover” on page 21. 3. At the rear of the server, press the release button to open the PCI card latch Figure 12. Opening the PCI card latch Chapter 5 Installing, removing, or replacing hardware...
Page 38 6. Install the new PCI card into the appropriate slot on the system board. See “Locating parts on the system board” on page 14. Note: If you are installing a PCI Express x16 card, make sure the memory slot retaining clips are closed before you install the PCI Express x16 card. ThinkServer TS130 Hardware Maintenance Manual...
Page 39: Installing Or Removing The Ethernet Card
7. Pivot the PCI card latch to the closed position to secure the PCI card. Figure 14. Installing a PCI card What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 54. Installing or removing the Ethernet card Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”...
Page 40: Installing Or Removing A Memory Module
PCI Express x16 card for easier access to the memory slots. See “Installing or replacing a PCI card” on page 24. 6. Depending on whether you are installing or replacing a memory module, do one of the following: ThinkServer TS130 Hardware Maintenance Manual...
Page 41 • If you are replacing an old memory module, open the retaining clips and gently pull the memory module out of the memory slot. Figure 15. Removing a memory module • If you are installing a new memory module, open the retaining clips of the memory slot into which you want to install the memory module.
Page 42: Installing Or Replacing The Optical Drive
• If you are installing a secondary optical drive, remove the plastic panel in the front bezel for the drive bay you want to use. If there is a metal static shield installed in the drive bay, remove the metal static shield. ThinkServer TS130 Hardware Maintenance Manual...
Page 43 • If you are replacing an optical drive, disconnect the signal cable and the power cable from the rear of the optical drive, press the blue release button and then slide the optical drive out of the front of the server. Figure 18.
Page 44: Replacing The Primary Hard Disk Drive
2. Remove the server cover. See “Removing the server cover” on page 21. 3. Locate the primary hard disk drive. See “Locating parts on the system board” on page 14. 4. Disconnect the signal cable and the power cable from the rear of the hard disk drive. ThinkServer TS130 Hardware Maintenance Manual...
Page 45 5. Press the blue release tab downward, slide the hard disk drive cage to the rear of the server, and then pivot it outward to completely remove the drive cage from the chassis. Then, pull on the blue handle to remove the hard disk drive from the drive cage. Figure 21.
Page 46 Note: There are two arrows, one on the upper drive cage and one on the hard disk drive cage. The arrows are aligned when the hard disk drive is in the correct position. Figure 23. Installing the primary hard disk drive ThinkServer TS130 Hardware Maintenance Manual...
Page 47: Installing Or Replacing The Secondary Hard Disk Drive
9. Connect one end of the signal cable to the hard disk drive and the other end to an available SATA connector on the system board. See “Locating parts on the system board” on page 14. Then, locate an available five-wire power connector and connect it to the hard disk drive. Figure 24.
Page 48 Note: If you are installing a 2.5-inch hard disk drive, install the hard disk drive into a 2.5-inch to 3.5-inch hard disk drive tray first and then install the tray into the blue bracket. Figure 26. Installing the hard disk drive into the bracket ThinkServer TS130 Hardware Maintenance Manual...
Page 49 9. Slide the new hard disk drive with the blue bracket into the secondary hard disk drive cage until it snaps into position. 10. Slide the hard disk drive cage with the new hard disk drive into the chassis until it is directly underneath the metal tab Figure 27.
Page 50: Installing, Removing, Or Replacing Hardware Devices
Replacing the power supply assembly Attention: Do not open your server or attempt any repair before reading and understanding “Safety information” on page iii and “Guidelines” on page 19. ThinkServer TS130 Hardware Maintenance Manual...
Page 51 This section provides instructions on how to replace the power supply assembly. Although there are no moving parts in your server after the power cord has been disconnected, the following warnings are required for your safety and proper Underwriters Laboratories (UL) certification. DANGER Hazardous moving parts.
Page 52 8. Install and tighten the four screws to secure the power supply assembly. Note: Use only screws provided by Lenovo. 9. Reconnect the power supply assembly cables to the system board and each of the drives.
Page 53: Replacing The Heat Sink And Fan Assembly
What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the replacement, go to “Completing the parts replacement” on page 54. Replacing the heat sink and fan assembly Attention: Do not open your server or attempt any repair before reading and understanding “Safety information” on page iii and “Guidelines”...
Page 54 10. Connect the heat sink and fan assembly cable to the microprocessor fan connector on the system board. See “Locating parts on the system board” on page 14. What to do next: • To work with another piece of hardware, go to the appropriate section. ThinkServer TS130 Hardware Maintenance Manual...
Page 55: Replacing The Front Audio And Usb Assembly
• To complete the replacement, go to “Completing the parts replacement” on page 54. Replacing the front audio and USB assembly Attention: Do not open your server or attempt any repair before reading and understanding “Safety information” on page iii and “Guidelines” on page 19. This section provides instructions on how to replace the front audio and USB assembly.
Page 56: Replacing The Front Fan Assembly
Note: If your server has a secondary hard disk drive installed, remove the secondary hard disk drive to get easier access to the power fan connector on the system board. See “Installing or replacing the secondary hard disk drive” on page 35. ThinkServer TS130 Hardware Maintenance Manual...
Page 57 5. Release the two tabs that attach the front fan assembly to the chassis as shown and then completely remove the front fan assembly from the chassis. Figure 34. Removing the front fan assembly Chapter 5 Installing, removing, or replacing hardware...
Page 58: Replacing The Rear Fan Assembly
2. Remove the server cover. See “Removing the server cover” on page 21. 3. Locate the rear fan assembly. See “Internal components” on page 15. ThinkServer TS130 Hardware Maintenance Manual...
Page 59 4. Disconnect the rear fan assembly cable from the system fan connector on the system board. See “Locating parts on the system board” on page 14. 5. The rear fan assembly is attached to the chassis by four rubber mounts. Remove the rear fan assembly by cutting the rubber mounts and gently pulling the rear fan assembly out of the chassis.
Page 60: Replacing The Microprocessor
The heat sink and microprocessor might be very hot. Turn off the computer and wait three to five minutes to let the computer cool before removing the computer cover. To replace the microprocessor, do the following: ThinkServer TS130 Hardware Maintenance Manual...
Page 61 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Remove the computer cover. See “Removing the server cover” on page 21. 3.
Page 62 12. Close the microprocessor retainer and lock it into position with the small handle to secure the new microprocessor in the socket. 13. Reinstall the heat sink and fan assembly. See “Replacing the heat sink and fan assembly” on page 41. 14. Reconnect all cables that were disconnected from the system board. ThinkServer TS130 Hardware Maintenance Manual...
Page 63: Replacing The System Board Battery
What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the replacement, go to “Completing the parts replacement” on page 54. Replacing the system board battery Attention: Do not open your server or attempt any repair before reading and understanding “Safety information” on page iii and “Guidelines”...
Page 64: Replacing The System Board
“Guidelines” on page 19. This section provides instructions on how to replace the system board. Note: This procedure must be performed only by trained service personnel of Lenovo. CAUTION: The heat sink and microprocessor might be very hot. Turn off the server and wait three to five minutes to let the server cool before removing the server cover.
Page 65 To replace the system board, do the following: 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2.
Page 66: Completing The Parts Replacement
5. Lower the microprocessor retainer and then lower the lever to secure the retainer. Make sure the lever is securely locked into position. Completing the parts replacement After completing the installation or replacement for all parts, you need to reinstall the server cover and reconnect cables. ThinkServer TS130 Hardware Maintenance Manual...
Page 67: Connecting The Cables
Setup Utility program. Refer to Chapter 6 “Configuring the server” on page 59. Note: In most areas of the world, Lenovo requires the return of the defective Customer Replaceable Unit (CRU). Information about this will come with the CRU or will come a few days after the CRU arrives.
Page 68: Turning On The Server
• The integrated management module (IMM) can turn off the server as an automatic response to a critical system failure. Connecting external devices If you install a supported optional adapter, you can attach external devices to the server. To attach an external device, do the following: ThinkServer TS130 Hardware Maintenance Manual...
Page 69: Updating The Server Configuration
Note: If you are attaching an external device, see the documentation that comes with the device for information about cabling. 1. Read and understand the Safety Information at http://www.lenovo.com/support, and “Guidelines” on page 19. 2. Turn off the server and all attached devices.
Page 70 ThinkServer TS130 Hardware Maintenance Manual...
Page 71: Chapter 6. Configuring The Server
Do not change the value of unfamiliar items or items that are not mentioned in this topic to avoid unexpected problems. If you consider changing the server configuration, proceed with extreme caution. Setting the configuration incorrectly might cause unexpected results. © Copyright Lenovo 2011, 2012...
Page 72 • Lenovo provides the BIOS update utility on the Lenovo Web site. You can download the BIOS image and follow the instructions on the Web site to update the BIOS. See “Updating system programs” on page 81. After updating the BIOS, all the BIOS settings become the default settings of the updated BIOS version.
Page 73 Table 5. Submenus under the System Summary menu Item Option or description CPU Type Show the CPU brand and CPU type. CPU Speed Show the CPU speed. CPU Core Count Installed Memory Show the total size of memory installed on the system board.
Page 74 AHCI and RAID. Depending on how the hard disk image was installed, changing this setting may prevent the system from booting. Native Mode Operation [Enabled] / Disabled Enable or disable native mode for ATA. ThinkServer TS130 Hardware Maintenance Manual...
Page 75 Table 10. Submenus under the ATA Drive Setup menu (continued) Item Option Description Hard Disk Pre-delay [Disabled] / 3 Seconds / 6 Seconds / 9 Force the BIOS to delay the Seconds / 12 Seconds / 15 Seconds initialization of hard disk drives for up / 21 Seconds / 30 Seconds to 30 seconds.
Page 76 Execute-Disable Bit Enable or disable the Execute-Disable Bit [Enabled] / Disabled function. This technology can prevent certain classes of malicious buffer overflow attacks if your server operating systems support this technology. ThinkServer TS130 Hardware Maintenance Manual...
Page 77 Table 15. Submenus under the CPU Setup menu (continued) Item Option Description ® Intel Virtualization Technology Enabled / [Disabled] Enable or disable the Intel Virtualization technology. This technology can provide additional capacity for hardware computing. If you set this feature to Enabled, you have to turn off the server and disconnect the power cord from electrical outlet, and then reconnect the...
Page 78 • VT100 , 8 bit • PC-ANSI, 7bit • PC-ANSI • [VT100+] • VT-UTF8 • ASCII Notes: 1. [ ] indicates the default setting. 2. The above options might vary depending on the type of the microprocessor. ThinkServer TS130 Hardware Maintenance Manual...
Page 79 Table 18. Items under the Power menu Item Option Description After Power Loss Power Off / Power On / [Last State] This field shows whether the system will stay on after ac power is removed and then restored. • Select Power On if you are using a power strip to turn the system on.
Page 80 Password will not be required when updating the system software. Require POP on Restart Yes / [No] If No is selected, the Power-On Password will only be required when the system is started with a cold boot. ThinkServer TS130 Hardware Maintenance Manual...
Page 81 Table 20. Items under the Security menu (continued) Item Option Description Hard Disk Password Enter the submenus to view all the options. See Table 21 “Submenus under the Hard Disk Password menu” on page 69. Fingerprint Setup Enter the submenus to view all the options.
Page 82 Note: When you set it as Inactive or Disabled, the TxT will be set to Disabled automatically. Clear TCG Security Feature Yes / [No] Select whether to clear TCG Security Feature settings. Note: [ ] indicates the default setting. ThinkServer TS130 Hardware Maintenance Manual...
Page 83 Table 23. Submenus under the Fingerprint Setup menu Item Option Description Preboot Authentication [Enabled] / Disabled Enable or disable the fingerprint reader function for BIOS password input. Erase Fingerprint Data Yes / [No] Select whether to clear fingerprint data stored in a fingerprint reader. Note: [ ] indicates the default setting.
Page 84: Viewing And Changing Settings
You can use either the keyboard or the mouse to navigate through BIOS menu choices. The keys used to perform various tasks are displayed at the bottom of each screen. ThinkServer TS130 Hardware Maintenance Manual...
Page 85: Using Passwords
Using passwords By using the Setup Utility program, you can set passwords to prevent unauthorized access to your computer and data. The following types of passwords are available: • Power-On Password • Administrator Password • Hard Disk Password You do not have to set any passwords to use your computer. However, using passwords improves computing security.
Page 86: Enabling Or Disabling A Device
(such as hard disk drives or the optical drive) are disabled and cannot be accessed. External SATA Port When this option is set to Disabled, the device connected to the External SATA connector cannot be accessed. ThinkServer TS130 Hardware Maintenance Manual...
Page 87: Selecting A Startup Device
To enable or disable a device, do the following: 1. Start the Setup Utility program. See “Starting the Setup Utility program” on page 59. 2. From the Setup Utility program main menu, select Devices. 3. Depending on the device you want to enable or disable, do one of the following: •...
Page 88: Raid Level
7. Press Enter to initiate volume creation. 8. When prompted, press Y to accept the warning message and create the volume. 9. If desired, return to step 2 to create additional RAID volumes. 10. When finished, select Exit and press Enter. ThinkServer TS130 Hardware Maintenance Manual...
Page 89: Deleting Raid Volumes
The firmware in the server is periodically updated and the latest firmware is always available for downloading from the Lenovo Web site. Go to http://www.lenovo.com/drivers and follow the instructions on the Web page to check for the latest level of firmware, such as the BIOS updates and device drivers.
Page 90: Using The Firmware Updater Program
The user guide for the program also is on the DVD and can be accessed directly from the program interface. If you do not have a ThinkServer EasyStartup DVD, you can download an ISO image from the Lenovo Support Web site and make a disc by yourself.
Page 91: Starting The Thinkserver Easystartup Program
• Downloads device drivers from the ThinkServer EasyStartup DVD according to the operating system • Selectable partition size and file system type • Ability to create a reuseable response file that can be used with similarly configured Lenovo servers to make future installations faster Starting the ThinkServer EasyStartup program This topic provides instructions on how to start the ThinkServer EasyStartup program.
Page 92: Using The Thinkserver Easystartup Program On A Windows Operating System
DVD. Notes: • You should read and accept the Lenovo License Agreement when prompted. • On the Microsoft Windows Server 2003 operating system, you might need to add the Uniform Resource Locator (URL) for the ThinkServer EasyStartup program Web page to the trusted Web site list so that the page can open correctly.
Page 93: Updating System Programs
Utility program by starting your computer with a system-program-update disc or running a special update program from your operating system. Lenovo might make changes and enhancements to the POST and BIOS. When updates are released, they are available as downloadable files on the Lenovo Web site at http://www.lenovo.com. Instructions for using the POST and BIOS updates are available in a TXT file that is included with the update files.
Page 94: Updating (Flashing) The Bios From Your Operating System
Updating (flashing) the BIOS from your operating system Note: Because Lenovo makes constant improvements to its Web sites, the Web page contents are subject to change without notice, including the contents referenced in the following procedure.
Page 95 14. Turn on the computer to restart the operating system. Chapter 6 Configuring the server...
Page 96 ThinkServer TS130 Hardware Maintenance Manual...
Page 97: Chapter 7. Troubleshooting And Diagnostics
“Selecting a startup device” on page 75. The server beeps multiple times Verify that no keys are stuck. before the operating system starts. Troubleshooting tables Use the troubleshooting tables to find solutions to problems that have identifiable symptoms. © Copyright Lenovo 2011, 2012...
Page 98: Hard Disk Drive Boot Error
Check the power-on switch for continuity. Beep symptoms Beep symptoms are tones or a series of tones separated by pauses (intervals without sound) during the POST. The following table describes beep symptoms and provides suggested actions to correct detected problems. ThinkServer TS130 Hardware Maintenance Manual...
Page 99: Post Error Codes
Symptom Error FRU/Action 3 short beeps and 1 long beep Memory not detected Perform the following actions in order: 1. Make sure that the memory module(s) are properly seated in the connector(s). 2. Replace the memory module(s). 3. Replace the system board. 2 short beeps Common POST error Indicates that an error has occurred...
Page 100: Easystartup Problems
Press F1 to enter the Setup Utility program. Then count exceeded press F10 to save the operation and exit the Setup Utility program. EasyStartup problems The following table describes the EasyStartup problems and suggested actions to correct detected problems. ThinkServer TS130 Hardware Maintenance Manual...
Page 101: Miscellaneous Error Messages
Table 27. ThinkServer EasyStartup DVD Follow the suggested actions in the order in which they are listed in the Action column until the problem is resolved. Symptom Action The ThinkServer • Make sure that the server supports the EasyStartup program and has a startable EasyStartup DVD will (bootable) DVD drive.
Page 102: Undetermined Problems
This topic provides instructions on how to find out the failing components. To find out the failing components, do the following: 1. Turn off the server. 2. Remove or disconnect the following components (if installed) one at a time. ThinkServer TS130 Hardware Maintenance Manual...
Page 103 a. External devices (modem, printer, or mouse) b. Any adapters c. Memory modules d. Extended video memory e. External cache f. External cache RAM g. Hard disk drive h. Diskette drive 3. Turn on the server to re-test the system. 4.
Page 104 ThinkServer TS130 Hardware Maintenance Manual...
Page 105: Chapter 8. Getting Information, Help, And Service
Using the documentation Information about your Lenovo system and installed software, if any, or optional device is available in the documentation that comes with the product. The documentation can include printed documents, online documents, readme files, and help files. Most of the documentation for your server is on the documentation DVD provided with your server.
Page 106: Help And Service
• Check the power switches to ensure that the system and optional devices are turned on. • Use the troubleshooting information in your system documentation on the documentation DVD that comes with your product. • Check for the updated information, new device drivers, and hints and tips on the Lenovo Support Web site at: http://www.lenovo.com/support If possible, be at your product when you call.
Page 107: Using Other Services
Service availability and service names might vary by country or region. For more information about these services, go to the Lenovo Web site at: http://www.lenovo.com...
Page 108 ThinkServer TS130 Hardware Maintenance Manual...
Page 109: Appendix A. Notices
Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any Lenovo intellectual property right may be used instead.
Page 110: Trademarks
Trademarks Lenovo, the Lenovo logo, and ThinkServer are trademarks of Lenovo in the United States, other countries, or both. Intel, Intel Core, Intel SpeedStep, Intel Xeon, Celeron, and Pentium are trademarks of Intel Corporation in the United States, other countries, or both.
Page 111: Polyvinyl Chloride (Pvc) Cable And Cord Notice
Lenovo encourages owners of information technology (IT) equipment to responsibly recycle their equipment when it is no longer needed. Lenovo offers a variety of programs and services to assist equipment owners in recycling their IT products. For information on recycling Lenovo products, go to: http://www.lenovo.com/lenovo/environment/recycling...
Page 112: Battery Return Program
If you want to replace it with a new one, contact your place of purchase or ask for a repair service provided by Lenovo. If you have replaced it by yourself and want to dispose of the disused lithium battery, insulate it with vinyl tape, contact your place of purchase, and follow their instructions.
Page 113: Requirements For Batteries Containing Perchlorate
Important WEEE information The WEEE marking on Lenovo products applies to countries with WEEE and e-waste regulations (for example, European Directive 2002/96/EC, India E-Waste Management & Handling Rules, 2011). Appliances are labeled in accordance with local regulations concerning waste electrical and electronic equipment (WEEE).
Page 114: China Rohs
China RoHS Turkish RoHS The Lenovo product meets the requirements of the Republic of Turkey Directive on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (EEE). ThinkServer TS130 Hardware Maintenance Manual...
Page 115: India Rohs
Energy aimed at saving money and protecting the environment through energy efficient products and practices. Lenovo is proud to offer our customers products with an ENERGY STAR compliant designation. Some models of the following machine types have been designed and tested to conform to the ENERGY STAR program requirement for computer servers at the time of manufacture: 1098, 1100, 1105, and 1106.
Page 116 For more information about ENERGY STAR, go to: http://www.energystar.gov Lenovo encourages you to make efficient use of energy an integral part of your day-to-day operations. To help in this endeavor, set the following power-management features to take effect when your servers have been used: •...
Page 117: Index
DisplayPort connector Input/Output (I/O) features documentation installing using device drivers drives Ethernet card bays installing options specifications memory module PCI card security features integrated functions EasyUpdate Firmware Updater program internal drives © Copyright Lenovo 2011, 2012...
Page 118 Setup Utility purchasing additional services Setup Utility program, starting Setup Utility, exiting size software RAID configuration utilities specifications software starting RAS features ThinkServer EasyStartup program rear connectors starting the Setup Utility program ThinkServer TS130 Hardware Maintenance Manual...
Page 119 TÜV gloss statement updating (flashing) the BIOS server configuration system programs updating (flashing) the BIOS updating firmware USB connector using documentation EasyUpdate Firmware Updater program other services passwords Setup Utility ThinkServer EasyStartup program VGA monitor connector © Copyright Lenovo 2011, 2012...
Page 120 ThinkServer TS130 Hardware Maintenance Manual...

This manual is also suitable for:

1098 1100 1105 1106

Lenovo ThinkServer TS130 Hardware Maintenance Manual

Safety Information

Chapter 1. General Information

Chapter 2. Server Setup Road Map

Chapter 3. Product Overview

Chapter 4. Locating Parts, Controls, and Connectors

Chapter 5. Installing, Removing, or Replacing Hardware

Chapter 6. Configuring the Server

Chapter 7. Troubleshooting and Diagnostics

Chapter 8. Getting Information, Help, and Service

Appendix A. Notices

Index

Quick Links

Related Manuals for Lenovo ThinkServer TS130

Summary of Contents for Lenovo ThinkServer TS130

This manual is also suitable for:

Table of Contents