13.5 hp electric start 38" mower 5 speed transaxle lawn tractor (61 pages)
Summary of Contents for Craftsman 917.270653
Page 1
Call: Read and follow all Safety Rules 1-800-659-5917 and Instructions before operat- ing this equipment. Sears Craftsman Help Line 5 am - 5 pm, Mon- Sat Seam, Roebuck and Co., Hoffman Estates, II 60179 Visit our Craltsman website:w_,w.sears,com/craftsman...
Page 2
Will not hold a charge, Sears will replace the battery at no charge. In-home warranty service on your Craftsman riding equipment is available at no charge for 30 days from the date of purchase. Please contact your nearest service center. After 30 days from the date of purchase, warranty service is available by taking your Craftsman riding equipment to your nearest Sears Service Center.
Page 3
DO NOT: • Turn off blades when not mowing. • Do not tum on slopes unless neces- • Stop engine before removing grass sary, and then, turn slowly and catcher or unclogging chute. gradually downhill, if possible. • Mow only in daylight or good artificial •...
Page 4
• Keep nuts and bolts, especially blade • Never make adjustments or repairs attachment bolts, tight and keep with the engine running. equipment in good condition. • Grass catcher components are subject • Never tamper with safety devices. to wear, damage, and deterioretion, Check their proper operation regularly.
Page 5
REPAIR PARTS section of this manual). CONGRATULATIONS on your purchase of a Craftsman Tractor. It has been designed, engineered and manufactured to give you the best possible depend- ability and performance. Should you expedence any problem you cannot easily remedy, please contact your nearest Sears Authorized Service Center.
Page 7
Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.
Page 8
TO ROLL TRACTOR OFF SKID (See Label Operation section for location end functlon of controls) • Press lift lever plunger and raise BatteP attachment lift tever to its highest Door position. • Release parking brake by depressing clutch/brake pedal. • Place gearshift lever in neutral (N) position.
Page 9
INSTALL MULCHER PLATE CHECK FOR PROPER POSITION OF ALL BELTS (if previously removed) • Re'me and hold deflector shield in See the figures that are shown for replacing motion and mower blade drive upright position. • Place front of mulcher plate over front belts in the Service and Adjustments section of this manual.
Page 10
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. ÷ BATTERY CAUTION OR REVERSE FORWARD FAST SLOW WARNING ENG,NEON ENG,NEOFF O,'PRESSORE L,ONTSON OV_,_T_.P _= FUEL CHOKE MOWER HEIGHT PARKING BRAKE UNLOCKED MOWER LIFT LOCKED...
Page 11
KNOWYOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of vadous controls and adjustments. Save this manuel for future reference. Ignition Switch Attachment Clutch Lift Amme_r ..
Page 12
The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.
Page 13
• Move gearshift lever to 1st gear. Be • The average lawn should be cut to sure you have allowed room for tractor approximately 2-1/2 inches dudng the cool season and to over 3 inches to roll slightly as you restart movement. •...
Page 14
ADD GASOLINE • Insert key into ignition and turn key clockwise to =START" position and • Fill fuel tank. Use fresh, clean, regular unleaded gasoline with a minimum of release key as soon as engine starts. 87 octane. (Use of leaded gasoline Do not run starter continuously for will Increase carbon and lead oxide more than fifteen seconds per minute.
Page 15
MOWING TIPS MULCHING MOWING TIPS • Mower should be properly leveled for IMPORTANT: For best performance, best mowing performance. See "TO keep mower housing free of built-up LEVEL MOWER HOUSING" in the grass and trash. Clean after each use. Service and Adjustments section of •...
Page 16
AS YOU COMPLETE "rim t_4m_'e R Ch=__" Loo_Famr_ t 1' L_'_ Checkk_e_y Level R c_an Battery a ndT_m C_eck Tr_a_ Coding Adjust Motion Ddve _dl(s) Tems_ ii_s En_ _ I/=j E Qean AlrFi.er Clean Air Scme_ MufflerfBped_ An'e_er Replace Spm'kPlug P,e_sce _r F_orP_ Cs*Iddge ReplaceFuel niter...
Page 17
TRACTOR IMPORTANT: To ensure proper assem- bly, center hole in blade must align with Always observe safety rules when star on mandrel assembly. performing any maintenance. • Reassemble hex bolt, lock washer and BRAKE OPERATION flat washer in exact order as shown. if tractor requires more than six (6) feet •...
Page 18
NOTE: Although multi-viscosityoils BAI"rERY (5W30, 10W30 etc.) improve starting in Your tractor has a battery charging cold weather, these multi-viscosity oils system which is sufficient for normal use. will result in increased oil consumption However, periodic charging of the battery when used above 32°F.
Page 19
ENGINE COOLING FINS • Clean cartddge by tapping gently on flat sudace. If very dirty or damaged, Remove any dust, dirt or oil from engine replace cartddge. cooling fins to prevent engine damage • Reinstall cartddge, nut, precleaner, from overheating. cover and secure with knob(s).
Page 20
CLEANING tWoe do not recommend using a garden se to clean your tractor unless the of all foreign matter. eloctricai system, muffler, air filter and Keep finished surfaces and wheels carburetor are covered to keep water out. lean engine, battery, seat, finish, etc. Water in engine can result in a short- free of all gasoline, oil, etc.
Page 21
TO LEVEL MOWER HOUSING • Before making any necessary adjust- ments, check that both front links are AdjuSt the mower while tractor is parked equal in length. Both links should be on level ground or driveway. Make sure tires areproperly inflated (See "PROD- approximately 10-3/8".
Page 22
TO REPLACE MOWER BLADE • Road test tractor for proper stopping DRIVE BELT distance as stated above. Readjust if The mower blade drive belt may be necessary. If stopping distance is still replaced without tools. Park the tractor greater than six (6) feet in highest on level surface.
Page 23
TRANSAXLE GEAR SHIFT LEVER • Replace washers end snap retaining ring secumty in axle groove. NEUTRAL ADJUSTMENT • Replace axle cover. The transexle should be in neutral when NOTE: To seal tire punctures and the gear shift lever is in neutral (N) (lock prevent fiat tires due to slow leaks, tire gate) position.
Page 24
Positive T erminal Negative Terminal Bolt IRed) Cable Negative (Black) Cable TO REPLACE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the Battery backside of the grill. • Replace bulb in holder and push bulb holder securely back into the hole in Negative Terminal Positive Ten_.nal...
Page 25
ENGINE TO ADJUST CARBURETOR Maintenance, repair, or replacement of NOTE: The carburetor on this engine is the emission control devices and low emission. It is equipped with an idle systems, which are being done at the fuel adjusting needle with a limiter cap, which allows some adjustment within the customers expense, may be performed limits allowed by the cap.
Page 26
ACCELERATION TEST Idle Speed Throttle Screw Lever • Move throttle control lever from slow to fast position. If engine hesitates or dies, turn idle mixture valve out (counter-clockwise) 1/8 turn. Repeat test and continue to adjust, if neces- sary, until engine accelerates smoothly.
Page 27
Immediately prepare your tractor for ethanol or methanol) can attract moisture storage at the end of the season or if the which leads to separation and formation tractor will not be used for 30 days or of acids dudng storage. Acidic gas can more.
Page 28
TROUBLESHOOTING CHART PROBLEM CAUSE CORRECTION Will not start * Out of fuel. • Fill fuel tank. Engine not "CHOKED _ * See "TO START ENGINE" properly. in Operation section. • Engine flooded. • Wait several minutes before attempting to start. •...
Page 29
TROUBLESHOOTING CHART PROBLEM CAUSE CORRECTION Engine clicks but • Weak or dead battery. • Recharge or replace battery. will not start • Corroded battery terminals. • Clean battery terminals. • Loose or damaged wiring. Check all wiring. • Faulty solenoid or starter. •...
Page 30
TROUBLESHOOTING CHART PROBLEM CAUSE CORRECTION Poor out - uneven • Worn, bent or loose blade. • Replace blade. TIghton blade bolt. • Mower deck not level. • Level mower deck. • Clean underside of mower • Buildup of grass, leaves, and trash under mower.
Page 31
TRACTOR -- MODEL NUMBER 917.270653 SCHEMATIC " BATTERY FUSE AMMETER (OP11(_'qAq ..STARTER L ..CLUTCH/ BRAKE (PEDALuP) ..(NOT SEAT OCCUPIED) SWITCH IGNITION SWITCH , ..X._ EtJCK kTI"MENT CLUTCH ..GROUNDING SPARK :.._=0_L; u.rr UHE ' EHGtNES) C_,Nq_Na S'_6t'EM OUTPUT M _*C¢_'rl ,¢C MIN.
Page 32
TRACTOR -- MODE L NUMBER 917.270653 ELECTRICAL...
Page 33
TRACTOR - - MODEL NUMBER 917.270653 ELECTRICAL PART DESCRIPTION 144925 Battery 12 VOLT 25 AMP 74760412 Bolt Hex Hd 1/4-20unc x 3/4 156417 Case Battery 16 153664 Switch, Interlock Push-in 21 166182 Hamese Asm LightW/4152J 22 4152J Bulb Ll_t #1156 24 4799J Cable Battery 6 Ga 11"...
Page 34
TRACTOR -- MODEL NUMBER 917.270653 CHASSISAND ENCLOSURES...
Page 35
TRACTOR - - MODEL NUMBER 917.270653 CHASSISAND ENCLOSURES KEY PART DESCRIPTION Chassis 169830 Drav/oar 16g061 17060612 Screw, Roll. 3/8-16 x 3/4 155272 BumperHood/Dash 168337X013 Dash. 10 STO533710 Bolt, Canfage 3/8-16 x 3/4 11 155927 Panel, Dash, L.H. 12 145660 Clip "rlnnermanGdlleP/t. 13 17210",'X010 Panel, Asm.
Page 36
TRACTOR - - MODEL NUMBER 917.27_53 GROUND DRIVE 2111...
Page 37
TRACTOR -- MODEL NUMBER 917.270653 GROUNDDRIVE PART PART DESCRIPTION DESCRIPTION Traneexie (See Breakdown) 61 17060612 Scraw 3/8-16 x 3/4 Peerless Model 206-545C 62 8883R Cover Pedal BIkRound 146682 Spdng Return Brake Tla Zk,,c 63 140186 Pulley Eng Ct Mech 38deg LTPtT 123666X Pulley Transaxle 18/20"...
Page 38
TRACTOR-- MODEL NUMBER 917.270653 STEERING ASSEMBLY...
Page 39
TRACTOR - - MODEL NUMBER 917.270653 STEERING ASSEMBLY PART DESCRIPTION 139768 SteeringWheel 154427 Front Axle Assembly 156483 Spindle Assembly, LH. 157473 Spindle Assembly, R.H. 6266H Beedng, Race, Thrust, Hardened 121748X Washer 25/32 x 1-5/8 x 16 Gauge 19272016 Washer 27/32 x 1-1/4 x 16 Gauge 1200O029 Ring, KIIp 3366R...
Page 40
TRACTOR - - MODEL NUMBER 917.270653 ENGINE I OPTIONAL EQUIPMENT Spark Arrester...
Page 41
TRACTOR-- MODEL NUMBER 917.270653 ENGINE KEY PART DESCRIPTION 162157 ControlThroffie/Choke 17720410 Screw Hex Thd Cut 1/4-20x5/8 T Engine (See Breakdown) ..Brigg,sModel 28U707-1174-E3 137352 Muffler Exhaust B&S Lt 13 165291 Gasket I 313 |d T_nPlated 14 13280324 Nipple Pipe 3/8 Npt X 3" 15 13200300 Etbow Std 90 Degree 3/8-18 Npt 16 STD551237...
Page 42
TRACTOR - - MODEL NUMBER 917.270653 SEATASSEMBLY KEY PART PART DESCRIPTION DESCRIPTION 140122 Seat 3350 BIk/olk Craftsman 13 121248X Bushing Snap BIk Nyl 50 Id 140551 Bracket Pnt Pivot Seat (blk) 14 72050412 Bolt Rdhd Sht Nk 1/4-20x1-1/2 71110616 Bolt Fin Hex 3/8-16unc X 1...
Page 43
TRACTOR -- MODE L NUMBER 917.270653 DECALS KEY PART PART DESCRIPTION DESCRIPTION 156368 Decal, Fender Decal, Opar. Instr. 11 163207 167178 Dec, a t, VJoelt Dr Sch Desal, Reptcmnt 12 146046 163200 Decal, Dash Decal, Hood Rh 163250 163202 Oecal, V-heR Schematic Oeca|, Hood Lh 14 160396 165388...
Page 44
TRACTOR -- MODEL NUMBER 917.270653 LIFTASSEMBLY...
Page 45
TRACTOR -- MODEL NUMBER 917.270653 LIFTASSEMBLY KEY PART DESCRIPTION 159460 Washer Asm Inner Spdng W/Plunger 159471 Shaft Asm. Lift RH 105767X Pin Groove 1200O002 ERing #5133-62 19211621 Washer 21/32 x 1 x 21 Ga. 120183X BeadngNylong 125631X Gdp Handle Ruted 122365X ButtonPlunger Reacl 11 139865...
Page 46
TRACTOR -- MODEL NUMBER 917.270653 MOWERDECK "_21 3 24...
Page 47
TRACTOR - - MODEL NUMBER 917.270653 MOWER DECK PART PART DESCRIPTION DESCRIPTION 165892 MowerDeckAssembly,42" 139888 Bolt, Shoulder 5/16-18 UNC STD533107 Bolt 53 131845 Arm Assembly, Pad, Brake 138017 Bracket Assembly,Sway Bar, 54 133943 Washer, Hardened Front 55 155O46 Arm, Idler 165460 Brecket Sway Bar 38/42"...
Page 48
TRACTOR - - MODEL NUMBER 917.270653 PEERLESSTRANSAXLE- - MODELNUMBER206-545C O _71B...
Page 49
TRACTOR - - MODEL NUMBER 917.270653 PEERLESSTRANSAXLE- - MODELNUMBER206-545C KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 772147 Transaxle Cover 41A 790079 Brake Lever 780086A Needle Beadng 5/8" 792073A Screw 114 - 20 x I-I 14" 770128 Transaxle Case 42A 792085A Screw I/4 - 20 x 2 I14"...
Page 50
TRACTOR - - MODEL NUMBER 917.270653 BRIGGS & STRATrON ENGINE-MODEL NUMBER 28U707, TYPE NUMBER 1174-E1 _614 lit REQUIRESSPECIALTOOL$ TO INSTALL. SEE REPAIR INSTRUCTIONMANUAl. 1026...
Page 51
TRACTOR -- MODEL NUMBER 917.270653 BRIGGS & STRAI"rON ENGINE-MODEL NUMBER 28U707,TYPE NUMBER 1174.E1 104 I 138 106N7' 117 _11_42_AI 121 CARBURETOR OVERHAUL 1_'_ _ 1033 VALVE OVERHAUL KIT A"REQUIRESSPECIALTOOUS TO tHSTALI. SEE REPAm INSTRUCllON MANUAL.
Page 52
TRACTOR - - MODEL NUMBER 917.270653 BRIGGS & STRATTON ENGINE-MODEL NUMBER 28U707,TYPE NUMBER 1174..EI 171 _ 977 CARBURETOR GASKET SET _224 1°°el...
Page 53
TRACTOR - - MODEL NUMBER 917.270653 BRIGGS & STRA'n'ON ENGINE-MODEL NUMBER 28U707, TYPE NUMBER 1174-E1 I,o,B _..L K,T I 11036 LABEL KIT- EMISSIONS] I,o- o..I.A.uA.I...
Page 54
TRACTOR -- MODEL NUMBER 917.270653 BRIGGS &STRATTON ENGINE-MODEL NUMBER 28U707, TYPE NUMBER 1174-E1 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 496412 Cylinder Assembly 94832 Screw, Pan Head 399265 Beadng, Cylinder 491323 Seal Governor Shaft 391086 * Seal, Oil 281346 Bushing, Throttle Shaft 494238...
Page 55
TRACTOR -- MODEL NUMBER 917.270653 BR|GGS & STRAI"rON ENGINE-MODEL NUMBER 28U707,TYPE NUMBER 1174-E1 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 810068 Screw, Set 871 262835 Bushing, Guide (Intake & 496280 Housing, Blower Exhaust) 94786 Screw,Hex, Head, 281361 Cover, Air Cleaner Blower Housing Mounting 875 495862...
Page 59
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION " _" ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SIGHTING SIGHT AND HOLD THIS LEVEL WITH SKY LINE OR TREE. Operate your Tractor up and down the face of slopes (not greater than 15 ), never across the face.
Page 60
For in-home major brand repair service: Call 24 hours a day, 7 days a week 1-800-4-MY-HOME (1-800-469-4663) Para pedir servicio de reparaci6n a domicilio 1-800-676-5811 In Canada for all your service and parts needs call Au Canada pour tout le service ou les pi_ces 1-800-665-4455 For the repair or replacement parts you need: Call 6 am - 11 pm CST, 7 days a week...