Operating The Dishwasher - Bosch SHE6AP02UC - Ascenta Ecosense 24" Built Owner's Manual

Operating the Dishwasher
SHX4AP, SHX5AL, SHX6AP
Off @ 6_,e ( P.... Auto Regular Delicate Quick RJ .....
........ 9h® / Sc,ub Wash Wash Wash Wash &Hold < \ _;/Clean O R nseAgent
Delay Haft Load Program Select
Depending on your model you wifl either have 4, 5 or 5 wash
cydes.
To start the dishwasher:
• Open the Door. Press the"ON/OFF" button.
• One of the Wash Cycle LEDs will be flashing. You can
now select a wash cycle.
• Press the "<" or ">" button to select the desired wash
cycle.
• Press the "START" button (LED stops flashing)
• Close the door to begin the cycle
NOTE
1. Rinse Agent Indicator Light will be illuminated if the
unit needs Rinse Agent.
2. If you close the door without pressing the start button
the unit will beep.
To cancel a cycle:
• Open the dishwasher door just far enough to expose
the control panel. Be careful of hot water splash out!
fou could be seriously scalded if you allow hot water to
_plash out of the dishwasher. OPENTHE DOOR CAREFULLY
:luring any wash or rinse cycle. Do not fully open the door
until water noises have stopped.
• Press and hold the "START/RESET" button until the
"Active" indicator light goes out.
• Close the door and wait for about 1 minute for the
dishwasher to drain.
• Open the door and press the"ON/OFF" button.
• You are now ready to start a new cycle.
To enter the options mode(rinse agent setting, extra
dry heat, cycle completion signal):
• Door must be open. Press the "ON/OFF" button to
turn the unit on.
• One of the Wash Cycle LEDs will be flashing.
• Press and hold down the ">" button, then press and
release the "START/RESET" button. Now release the
">" button.
18
• The "Clean" and one other LED will be flashing. You are
now in the options setup mode.
• Press ">" to select the option you would like to adjust.
If the "Clean" and "Rinse Agent" LED are flashing you can
adjust the Rinse Agent settings.
If the "Clean" and "Sanitized" LED are flashing you can set
the Extra Dry Heat.
To set the amount of Rinse Agent:
NOTE: If your glasses have spots on them, you need more
rinse agent. If your glasses have streaks, you need less
Rinse Agent.
Follow the prior instructions to enter "options" mode. With
the "Clean" and "Rinse Agent" LEDs flashing:
• Press the "<" button to change the amount of rinse
agent dispensed.
0 LEDs flashing --> Rinse Agent dispenser is OFF
1LED flashing --> Lowest amount of rinse agent
2 LEDs flashing --> Medium amount dispensed
3 LEDs flashing --> Highest amount of rinse agent
Press "START"to save your settings.
To turn Extra Dry Heat on or off:
With the "Clean" and "Sanitized" LEDs flashing:
• Press the "<" button to turn Extra Dry Heat on or off.
The wash cycle LEDs will illuminate when you press
II_II
0 LEDs flashing --> Extra Dry Heat is OFF
1LED flashing --> Extra Dry Heat is ON
To set the Cycle Completion Signal:
With the "Clean", "Sanitized", and "Rinse Agent" LEDs
flashing:
• Press the "<" button to change the cycle completion
tone level. The wash cycle LEDs will illuminate when
you press "<".
0 LEDs flashing --> Cycle Completion Signal is OFF
1LED flashing --> Low tone level
2 LEDs flashing --> Medium tone level
3 LEDs flashing --> Highest tone level
• Press STARTto save your settings.