Table of Contents
Advertisement
LY
HOW TO SET UP YOUR TRACTOR
PREPARE
BATTERY
(See Fig. 2)
H i, ii . ..........................
illllllll i i
CAUTION: Wear eye and face shield.
Wash hands or clothing immediately if
accidentally in contact with batteryacid.
Do not smoke.
Fumes from charged
battery acid are explosive.
Read the instructions included with the
battery vent caps. Always wear gloves,
clothing and goggles to protect your
hands, skin and eyes.
llllllllli i
....................
Your unit has a battery charging system which is sufficient
for normal use. However', pedodic charging of the battery
with an automotive charger will extend its life.
•
See instructions packed with vent caps in parts bag.
o
Fill battery with acid. Fill each cell until it reaches the
bottom of the vent wells. Do not overfi&
•
Allow battery to stand and settle for at least thirty
minutes. After standing, check the level of acid.
If
below the vent wells, add more acid until the correct
level is reached.
While battery is standing
(after adding acid) and later, while
battery is being charged,
continue
with assembly
of unit,
IMPORTANT;
TO
MAXIMIZE
THE
LIFE
OF YOUR
BATTERY,
IT tS NECESSARY
THAT THE BATTERY BE
CHARGED
BEFORE
USE_
FAILURE
TO
CHARGE
BATTERY
CAN RESULT
IN A SHORTENED
BATTERY
LIFEo
°
Charge battery at a rate of 6 amperes for I hour, Use
a 12 volt battery charger_Observe all safety precautions
required for battery charging°
o
Check the acid level after' the battery is charged. If the
acid has fallen below the correct level, add distilled or
iron free water.
•
install the vent caps to cover the vent wellsoWash the
top of the battery with water to remove any acid, then
wipe dry,.
°
Check battery case for leakage to make sure that no
damage has occurred in handling.
°
Dispose of excess battery acid,, Neutralize acid for'
disposal by adding it to four inches of water' in a five
gallon plastic container. Stir with a wooden or plastic
paddle while adding baking soda until the addition of
more soda causes no more foaming,.
•
Follow instructions on how to install battery.
CUT AWAY VIEW
[
BATTERY
CELL ACID
LEVEL
INSTALL SEAT (See Fig. 3)
Adjust seat before tightening adjustment knob_
•
Remove cardboard packing on seat pan,
°
Place seat on pan and assemble shoulder bolt.
o
Assemble adjustment knob and flat washer loosely.
Do not tighten.
=
Tighten shoulder bolt securely.
°
Lower seat into operating position and sit on seat.
°
Slide seat until a comfortable position is reached which
allows you to press clutch/brake pedal alFthe way down
(See Fig. 8).
°
Get off seat without moving its adjusted position.
°
Raise seat and tighten adjustment knob securely.
SEAT
SEAT PAN
SHOULDER
BOLT
FLAT WASHER
ADJUSTMENT
KNOB
FIG. 3
CHECK TIRE PRESSURE
The tires on your unit were overinfiated at the factory for
shipping purposes.
Correct tire pressure is important for
best cutting performance.
=
Reduce tire pressure to PSI shown in "PRODUCT
SPECIFICATIONS
on page 3 of this manual°
CHECK DECK LEVELNESS
For best cutting,results, mower housing should be properly
leveled.
See TO LEVEL MOWER HOUSING" in the
Service and Adjustments section of this manual.
CHECK
FOR PROPER
POSITION
OF ALL
BELTS
See the figures that are shown for replacing motion and
mower blade drive belts in the Service and Adjustments
section of this manual,
Verify that the belts are routed
correctly.
CHECK BRAKE SYSTEM
After you learn how to operate your tractor, check to see
that the brake is properly adjusted° See TO ADJUST
BRAKE" in the Service and Adjustments section of this
manual.
FIG, 2
8
Hide quick links:
Advertisement
Table of Contents
