LG 50PV450C Owner's Manual page 122

Z
X
122
12.
13.
14.
15.
16.
17.
OSD Select (Command: k I)
To select OSD (On Screen Display) on/off.
TransmisSiOn [k] [I] [ ] [Set ID] [] [Data] [Cr]
Data 00: OSD off Data 01 : OSD on
ACknowledgemen_ [I] [ ][Set ID] [ ] [OK/NG] [Data] [x]
Remote Control Lock Mode (Command: k m)
To lock the remote control and the front panel controls
on the TV.
Transmission [ k] [m][] [SetID][ ] [Data][Cr]
Data 00: Lock off Data 01 :Lock on
Acknowledgement[m][] [set ID] [ ] [OKiNG] [Data] [x]
If you're not using the remote control and front panel
controls on the TV, use this mode. When main power is
on/off, remote control lock is released.
Treble (Command: k r)
To adjust treble.
You can also adjust treble in the AUDIO menu.
Transmission [k] [r] [ ] [Set I D] [ ] [Data] [Cr]
Data Min: O0 ~ Max: 64 (*transmit by Hexadecimal code)
*Refer to 'Real data mapping'.
Acknowledgement [r][] [set ID][] [OKiNG] [Data] [x]
Bass (Command: k s)
To adjust bass.
You can also adjust bass in the AUDIO menu.
TransmissiOn [k] [s][] [set ID] [] [Data] [Cr]
Data Min: O0 ~ Max: 64 (*transmit by Hexadecimal code)
*Refer to 'Real data mapping'.
Acknowledgemen_ [s] [ ] [Set ID] [ ] [OK/NG] [Data] [x]
Balance (Command: k t)
To adjust balance.
You can also adjust balance in the AUDIO menu.
Transmission[k] [t][] [Set ID][] [Data] [Cr]
Data Min: O0 ~ Max: 64 (*transmit by Hexadecimal code)
*Refer to 'Real data mapping'.
Acknowledgement[t] [] [Set ID] [] [OK/NG] [Data] [x]
Color Temperature (Command: x u)
To adjust color temperature.
You can also adjust color temperature in the PICTURE menu.
Transmission[x] [u][] [Set ID] [ ] [Data] [Cr]
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
*Refer to 'Real data mapping'.
Acknowledgement[u] [] [Set ID] [] [OK/NG] [Data] [x]
1 8. ISM Method (Command: j p)
To avoid having a fixed image remain on screen.
Transmission[j] [p][] [Set ID] [ ] [Data] [Cr]
Data 02: Orbiter 04: White Wash
08: Normal 20: Color Wash
Acknowledgement[p] [ ] [Set ID][ ] [OK/NG] [Data] [x]
1 9. Energy saving (Command: j q)
To control the low energy function on/off.
TransmissiOn [j ] [q] [ ] [Set ID][] [Data] [Cr]
Data 00: Energy Saving off
01 : Energy Saving: Minimum
02: Energy Saving: Medium
03: Energy Saving: Maximum
05: Screen Off
10: Intelligent Sensor
Acknowledgement [q][] [set ID][ ] [OKiNG] [Data] [x]
20. Auto Configuration (Command: j u)
To adjust picture position and minimize image shaking
automatically. Auto configuration only works in RGB-PC
mode.
Transmission [j ] [u] [ ] [Set ID][] [Data] [Cr]
Data 1 : To set
Acknowledgemenf [u][] [set iD] [ ] [0K/NG] [Data] [x]
21. Channel Tuning (Command: m a)
To tune channel to following physical/major/minor number.
Trans_iiiio_ [m] [a][] [set iD][] [DataOo] [ ] [Data01 ]
[ ] [Data02] [] [Data03] [] [Data04] [] [Data05] [Cr]
Digital channels have a Physical, Major, and Minor channel
number. The Physical number is the actual digital channel
number, the Major is the number that the channel should
be mapped to, and the Minor is the sub-channel. Since
the ATSC tuner automatically maps the channel to the
Major number, the Physical number is not required when
sending a command.
Data 00: Physical Channel Number
NTSC air: 02~45, NTSC cable: 01,0E-7D
ATSC air: 01 ~45, ATSC cable: 01 ~87
Data 01 & 02: Major Channel Number
Data 01 : High byte Data 02: Low byte
Two bytes are available for the Major and Minor, nor-
mally only the second byte is used.
Data 03 & 04: Minor Channel Number
Not needed for NTSC.