Daylight-Saving Time - Emerson EWC19T5 Owner's Manual

AUTOMATIC CLOCK SETTING
Make sure ...
•
The unit must be turned on.
•
Confirm the unit is receiving a RF (Radio
Frequency) signal from either an antenna or cable
system connection using the ANT. jack on the rear
of the unit.
NOTES:
•
If a cable converter box is being used, make sure it
is powered on.
•
You must use the remote control to perform the
clock setting procedure.
•
If the unit is connected directly to a cable converter
box or satellite box, the local PBS station must be
selected on the cable box itself and the unit must be
set to the output channel of the cable converter box
or satellite box (usually channel 3 or 4), to be able
to set up or correct the clock automatically.
1
Select "SETTING CLOCK"
Hit [SETUP].
Press [K / L] to select
"SETTING CLOCK", then hit
[ENTER] .
2
Set "AUTO CLOCK" to [ON]
Hit [ENTER] to select [ON].
3
Begin "AUTO CLOCK CH SEARCH"
Hit [L] to select "AUTO CLOCK
CH SEARCH".
Then hit [ENTER].
•
The unit begins searching for the
station which contains the auto
clock set signal. The search for a
signal may take up to 20 seconds per channel.
•
When the search has ended, "_ _"
appears at the lower left of the
screen.
•
Write down the number(s) that
appear on the screen. They are the
auto clock station(s) in your area.
•
If no number(s) appear on the TV screen, there are
no stations in your area which contain the Auto
Clock signal. Auto Clock Setting is not possible.
Please use Manual Clock Setting on page 18.
NOTE:
•
During AUTO CLOCK CH SEARCH, the picture
may be distorted.
4
Hit [RETURN] to go back to "SETTING CLOCK"
menu.
Hit [L] to select "AUTO CLOCK
CH".
Press [s / B] until you locate Auto
Clock Set station number.
5
Hit [SETUP] to exit the menu.
NOTE:
•
Once the unit is turned off, it will periodically
check and set the correct date and time.
- TV/VCR SETUP -
TIMER PROGRAMMING
B SETTING CLOCK
Select this feature and the unit's clock automatically
CHANNEL SET UP
USER'S SET UP
will advance one hour in April, then reverse one hour
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
in October.
ZERO RETURN
TIME SEARCH
INDEX SEARCH
When Daylight-Saving Time is ON, the clock will
change automatically as follows:
•
First Sunday of April :
– SETTING CLOCK –
B AUTO CLOCK [ON] ately changes to 3 AM. Any timer programming
AUTO CLOCK CH SEARCH
you have set to occur between 2 AM and 3 AM will
AUTO CLOCK CH [ 02 ]
not record.
MANUAL CLOCK SET
•
D.S.T. [OFF]
Last Sunday of October :
immediately changes to 1 AM.
Make sure ...
•
The unit must be turned on.
– SETTING CLOCK –
AUTO CLOCK [ON]
B AUTO CLOCK CH SEARCH
1
AUTO CLOCK CH [ 02 ]
MANUAL CLOCK SET
Hit [SETUP].
D.S.T. [OFF]
Press [K / L] to point to "SET-
TING CLOCK", then hit [ENTER].
– AUTO CLOCK CH SEARCH –
08 10 13
2
Press [K / L] to point to "D.S.T.",
_ _ then hit [ENTER] until [ON]
appears.
3
Hit [SETUP] to exit the menu.
TO CANCEL THE DAYLIGHT-SAVING
TIME
Repeat steps 1 to 2 and select [OFF] using
[ENTER].
- 19 -
Enter the channel number that contains the
Automatic Clock Setting Signal
Exit the setting clock mode

DAYLIGHT-SAVING TIME

At 2 AM the clock immedi-
Select "SETTING CLOCK"
Set "D.S.T." (Daylight-Saving Time) to [ON]
Exit the Daylight-Saving Time mode
– SETTING CLOCK –
AUTO CLOCK [ON]
AUTO CLOCK CH SEARCH
B AUTO CLOCK CH [ 45]
MANUAL CLOCK SET
D.S.T. [OFF]
TV/VCR
At 2 AM the clock
- TV/VCR SETUP -
TIMER PROGRAMMING
B SETTING CLOCK
CHANNEL SET UP
USER'S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– SETTING CLOCK –
AUTO CLOCK [ON]
AUTO CLOCK CH SEARCH
AUTO CLOCK CH [ 02 ]
MANUAL CLOCK SET
B D.S.T. [ON]
EN