Advertisement
Quick Links
DEALER SET-UP INSTRUCTIONS for EUROPEAN SNAPPER
21" STEEL DECK "M" MODEL WALK BEHIND MOWERS
This SNAPPER Walk Behind Mower uses a handle engine control bail system to kill the engine for the SAFETY of
the operator. These mowers are designed for quick set-up. The checklist on Page 4 should be filled out by the
dealer as the items are checked off and/or performed and the Consumer/Operator Product Registration card filled
out and sent to the Customer Service department at SNAPPER when completed. CAUTION: Cutting blades are
extremely sharp. Wear heavy leather gloves when handling or working with blades. Be careful to avoid cutting
yourself on sharp edges of blade.
PUSH MODELS
STEP 1: Remove mower from shipping carton. Mower
shown as removed from shipping carton with handles
folded in Figure 1.
MOWER SHOWN AS REMOVED FROM SHIPPING
CARTON WITH HANDLES FOLDED (PUSH
MODEL SHOWN)
STEP 2: Remove and discard cardboard from between all
handles. Raise upper handle until it is in line and seats
into lower handle. Securely tighten upper handle T-Knobs
on both sides. See Figure 2.
UPPER
HANDLE
UPPER
T-KNOB
HANDLE
FIGURE 1
LOWER
LOWER
HANDLE
HANDLE
T-KNOB
FIGURE 2
STEP 3: Raise upper and lower handle until it seats into
position in the lower handle brackets. Securely tighten
lower handle T-Knobs on both sides. See Figure 3.
IMPORTANT: DO NOT tip machine with carburetor or
spark plug down. Oil from crankcase will saturate the air
filter and cause the engine to be hard to start or not start
at all. If contamination does occur, the air filter will have to
be replaced.
IMPORTANT: DO NOT tip machine with carburetor or
spark plug down. Oil from crankcase will saturate the air
filter and cause the engine to be hard to start or not start
at all. If contamination does occur, the air filter will have to
be replaced.
STEP 4: Tip mower back against the upper handle to gain
access to cutting blade. Remove foam shipping block
from cutting blade. This must be removed before starting
the engine.
LOWER
HANDLE
BRACKET
UPPER HANDLE &
LOWER HANDLE
SHOWN IN POSITION
FIGURE 3
INSTRUCTION No. 7-3133 (REV 1, 2/12/01)
LOWER
HANDLE
T-KNOB
Advertisement
Related Manuals for Snapper 21” STEEL DECK “M” WALK BEHIND MOWER Set-up
Summary of Contents for Snapper 21” STEEL DECK “M” WALK BEHIND MOWER Set-up
- Page 1 21” STEEL DECK “M” MODEL WALK BEHIND MOWERS This SNAPPER Walk Behind Mower uses a handle engine control bail system to kill the engine for the SAFETY of the operator. These mowers are designed for quick set-up. The checklist on Page 4 should be filled out by the dealer as the items are checked off and/or performed and the Consumer/Operator Product Registration card filled out and sent to the Customer Service department at SNAPPER when completed.
- Page 2 STEP 5: Handle height is adjustable for different height of STEP 6: Set-up is now complete for push models operators. Loosen the two nuts on the inside of each of without self-propelled drive system. For self-propelled the lower handles. See Figure 4. Move the handle up or models continue to the “Self-Propelled Models”...
- Page 3 STEP 8: Driven disc to drive disc adjustment is set up at C. Slide driven disc assembly over until 1/8” from the factory. In case driven disc may need adjustment, outside edge of drive disc. Maintaining the 1/8” proceed as follows: measurement, remove any looseness from the linkage.
- Page 4 IMPORTANT: This form is to be retained by the Dealer for future reference regarding Warranty, proof of purchase, traceability for product recall or service, etc. Complete the Product Registration Card and Mail to Customer Service Department at SNAPPER, P.O. BOX 1379, McDonough, Georgia, 30253. INSTRUCTION No. 7-3133 (REV 1, 2/12/01)